Logik LDW45S10 Handleiding

Logik Vaatwasser LDW45S10

Lees hieronder de 📖 handleiding in het Nederlandse voor Logik LDW45S10 (2 pagina's) in de categorie Vaatwasser. Deze handleiding was nuttig voor 7 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Thank you for purchasing a Logik dishwasher.

Please refer to this guide for the installation process.

1. Remove all packaging before positioning the machine. (Fig 1)

2. Please ensure the dishwasher is installed by a qualied technician. Refer to the tools required in Fig 2.

3. Ensure there is clearance each side of the unit to allow slight sideways movement for servicing when

required. Good levelling is essential for correct closure and sealing of the door. When the unit is correctly

levelled, the door should not catch the inner liner on either side of the cabinet. The adjustable feet may

be loosened or tightened in order to obtain the optimum leveling of the unit. (Fig 3)

4. If required, the worktop of the dishwasher can be removed. The height without the worktop is 820 mm.

Figure 3 outlines the minimum dimensions required to accommodate the dishwasher within tted

kitchen furniture units.

Do not connect the unit to the mains before installation. Ensure you are not installing the unit right in

front of the mains. This is to avoid potential damage to the back of the unit. (Fig 4)

5. The condensation strip must be tted to the underside of the worktop above your dishwasher to protect

it against any moisture. Its purpose is to protect your worktop’s underside from steam rising from the

dishwasher. (Fig 5 and 6)

• Ensure the surface is clean prior to sticking the condensation strip to the underside of the worktop.

• Remove the backing paper from the condensation strip. (Fig 5)

• Stick the condensation strip to the underside of the worktop. (Fig 6)

NOTE: FAILURE TO ATTACH THE CONDENSATION STRIP COULD RESULT IN DAMAGE TO THE UNDERSIDE OF

YOUR WORKTOP!

6. The worktop can be removed by removing the xing screws located at the rear of the dishwasher (Fig 7).

After removing the screws, lift and push the worktop forward to release the lugs from the front section of

the dishwasher. The polystyrene block and the lugs should be saved for future use.

7. Position the dishwasher next to a water tap and a drain. Ensure the water inlet and drain hoses are

not kinked or squashed. The unit must not stand on the mains cable. (Fig 8)

8. Make sure your plumbing is suitable for use with the dishwasher. If in doubt contact a qualied plumber.

This unit MUST BE connected to COLD WATER MAINS using the new water inlet hose. OLD HOSE SETS

MUST NOT BE RE-USED. The water pressure from the water mains needs to be at a minimum of 0.04 MPa

and a maximum of 1.00MPa.

Dishwasher Installation Guide

8. (continued)

• Connect one end of the safety water supply hose to your

dishwasher, and then connect the other end of the hose

to your water mains (Fig A). Please ensure the black

rubber seal is in place.

• After connecting the hose, turn on your water mains and

check for leaks.

• Connect the dishwasher to the mains socket.

NOTE: YOU MAY USE A Y-ADAPTOR (NOT INCLUDED)

FOR ADDITIONAL WATER FEED FOR ANOTHER APPLIANCE,

FOR INSTANCE A WASHING MACHINE. THIS IS ONLY

APPLICABLE FOR COLD WATER MAINS. A Y-ADAPTOR IS

AVAILABLE FROM MOST DIY STORES. (Fig A)

• Do not bend your drain hose. (Fig B)

• You may use the U-shaped drain hose holder to secure

your drain hose and to avoid bending it. (Fig C)

• Secure the water drain hose to the waste pipe to avoid it

coming o during the washing process. (Fig 9 and D)

NOTE: THE WASTE PIPE MUST ONLY BE CONNECTED TO

THE FOUL DRAINS AND NOT THE SURFACE WATER

DRAINAGE SYSTEM.

THE WATER DRAIN HOSE SHOULD BE PLACED BETWEEN 40

CM AND 100 CM FROM THE FLOOR LEVEL AND MUST NOT

BE EXTENDED, OTHERWISE THE UNIT MAY NOT BE ABLE TO

EXPEL THE WASTE WATER PROPERLY.

Awater mains

safety water supply hose

water drain hose

U-shaped drain hose

holder

Y-Adaptor

(not included)

Connect to

another

appliance

if required.

Logik LDW45S10_IG_GB_p1_100225.pdf 1 2/25/10 1:42 PM

123

4 5 6

7 8

450

600

unit in mm

850

450

620

min.100

Remove

level level

level

Unscrew

Stick the Condensation Strip

under the worktop, where you

want to install the dishwasher.

Leave some space

ST4 screws

Logik LDW45S10_IG_GB_p2_100322.pdf 1 3/22/10 4:05 PM

Product specificaties

Merk:	Logik
Categorie:	Vaatwasser
Model:	LDW45S10

Heb je hulp nodig?

Als je hulp nodig hebt met Logik LDW45S10 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Vaatwasser Logik

Logik LDW45S10 Handleiding

14 September 2023

Logik LID60W14N Handleiding

14 September 2023

Logik LID45W13N Handleiding

14 September 2023

Logik LS474WN Handleiding

14 September 2023

Logik LDW60W18N Handleiding

14 September 2023

Logik LDW45S12 Handleiding

14 September 2023

Logik LDW60X16N Handleiding

14 September 2023

Logik LID45W15N Handleiding

14 September 2023

Logik LDW45W15N Handleiding

14 September 2023

Logik LDW45W16N Handleiding

14 September 2023

Handleiding Vaatwasser

Nieuwste handleidingen voor Vaatwasser

Bosch SBD6ECX00E Handleiding

23 November 2024

Bosch SMU6ECS08E Handleiding

23 November 2024

Bosch SMS6ECW51E Handleiding

23 November 2024

Bosch SMU4ECS24E Handleiding

23 November 2024

Bosch SMI4ECS24E Handleiding

23 November 2024

Bosch SMU4ETS00E Handleiding

23 November 2024

Bosch SMI6YAS04E Handleiding

23 November 2024

Bosch SMU4HCS52E Handleiding

23 November 2024

Bosch SMI4EAS24E Handleiding

23 November 2024

Bosch SMI6ZCS17E Handleiding

23 November 2024