Liftmaster SRDRST Handleiding
Lees hieronder de đ handleiding in het Nederlandse voor Liftmaster SRDRST (6 pagina's) in de categorie Toegangscontrolesysteem. Deze handleiding was nuttig voor 4 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/6

1
SMART READER
INSTALLATION GUIDE
Included Parts:
⢠Reader, Backplate, Wall Plate
⢠#6 Machine Screws â QTY 2
⢠#6 Self Tapping Screws â QTY 2
⢠#4-40 Phillips Screw
⢠#4-40 Pin-in-Torx Screw
Wiring Connections
Red Power In
Black Ground
Shield Shield Ground
Green Wiegand Data 0
RS485A(+)
White Wiegand Data 1
RS485A(â)
Yellow* Beeper Control
Brown* Tamper Out
Blue* Green LED Control
Orange Red LED Control*
â˘
Single Gang Keypad
RF TECHNOLOGIES Model Model
125 kHz, 13.56 MHz & BLE Mobile SRDRST SRDRKP
CURRENT 120 mA average, 170 mA peak 145 mA average, 195 mA peak
VOLTAGE 5-16 VDC (NEVER APPLY MORE THAN 16V)
TEMPERATURE UL⢠tested â35° to 66°C and EN â40° to 70°C and 95% humidity
(UL⢠tested -31ËF to 150ËF and EN -40Ë to 158ËF and 95% humidity)
CABLE LENGTH
Communication Lines
Wiegand: 200 feet - 22 AW G
300 feet - 20 AWG
500 feet -18 AWG
OSDP @ 12 VDC and 25ËC (77ËF) = 1000 feet - 22 AWG Twisted Pair
NOTE: Do NOT use the Power Supply provided with the CAPXLV or CAPXM to directly power up this reader. It is 24V and will cause damage to the reader.
NOTE: LED Control not available when connected to a CAPXS.
Tools Needed (Not Supplies):
⢠Phillips Screwdriver
⢠1â (25 mm), 1/8â Drill bits
⢠T8 Security Torx Bit (optional for increased tamper detection)
⢠#6-32 Tap if required
*These wires are only used in Wiegand mode.
**All wiring methods used shall be in accordance
with the National Electrical Code, ANSI/NFPA 70.
Readers must be powered by a compatible UL
Listed, power limited, access control panel rated
5â16 VDC.
A. Install the Metal Wall Plate to the Wall/Single Gang box.
⢠Use the provided #6 screws.
B. Wire the Cable to the Control Panel.
C. Attach the Reader to the Wall Plate and Install the Reader Screw.
⢠Follow steps 1 through 3 below to ensure proper alignment. Install either the #4-40
screw or Pin-in-Torx screw at the bottom.
WARNING: This product can expose you to chemicals including lead, which are known
to the State of California to cause cancer or birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.

2
Reader Startup Sequence
On power up, the Smart readers provide an LED and beeper sequence to provide information about the reader type and its communication mode. The
ďŹrst sequence describes the RF technologies built in the reader: First, an LED sequence will indicate the supported RF protocols.
BLE High-Frequency Low-Frequency
Red LED ďŹash Green LED ďŹash Amber LED ďŹash
After the above AV sequence identiďŹes the supported RF protocols, the reader will then indicate the supported host communication using beep/ďŹash
sequences.
Wiegand Only OSDP Only Auto-Detect
Beep and Blink Red LED once Beep and Blink Green LED 2 times Beep and Blink Green LED 4 times
Keypad Mode Setup
Within one minute of reader reset, enter the keypad conďŹg code: *88889999. The reader beeps three times. LED ďŹashes amber for each beep. Within
2 seconds of entering the keypad conďŹg code, press the corresponding key code below for the desired format. The reader then beeps three times, LED
ďŹashes amber for each beep.
4-Bit Format 8-Bit Format 26-Bit Format*
*4 *8 #XXX
*Within 2 seconds of pressing the # key, enter the facility code youâd like to use (0-255) using 3 digits. For example, code 077 for facility code 77. The
key presses are buffered. Up to 5 key presses are buffered.
Test and Installation Tips
⢠Power the reader and verify Reader Startup Sequence.
⢠Present a valid credential, reader should beep, ďŹash Green, and report the credential to the panel.
⢠If the Badge is read, but no credential is reported at the panel, verify panel wiring and panel setup.
⢠By default, the reader will transmit credential and keypad data in Wiegand communication mode.
⢠The reader is always listening for an incoming OSDP message. If a message is received during this period, the reader will automatically switch to OSDP-only communication
mode.
⢠When connecting the reader to an OSDP panel, connect the green wire to RS485A(TR+), and the white wire to RS485B(TR-).
⢠If Green and White wires are connected backwards to an OSDP Panel, the reader will ďŹash red and amber.
⢠In OSDP, the default baud rate is 9600 and starts up at Address 0.
⢠Readerâs ConďŹguration Part Number (CPN) on the label controls the Smart Card Support information.
Additional technical details and regulatory information can be found through the QR Code at top of the front page
Performance Levels
⢠Destructive Attack: I
⢠Line Security: I
⢠Endurance: IV (125 kHz, 13.56 MHz), I (BLE)
⢠Standby Power: I
Approvals
EN302291, EN301489, EN300330, IP55, UL294
Patents - US9558377 & US9747738B1
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
⢠Reorient or relocate the receiving antenna.
⢠Increase the separation between the equipment and receiver.
⢠Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
⢠Consult the dealer or an experienced radio/TV technician for help.
This telecommunication equipment conforms to NTC technical requirement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canadaâs licence-exempt RSS(s). Operation is subject to the following two conditions: 1.This device may not cause interference. 2. This device must
accept any interference, including interference that may cause undesired operation of the device.
LâĂŠmetteur/rĂŠcepteur exempt de licence contenu dans le prĂŠsent appareil est conforme aux CNR dâInnovation, Sciences et DĂŠveloppement ĂŠconomique Canada applicables aux
appareils radio exempts de licence. Lâexploitation est autorisĂŠe aux deux conditions suivantes: 1. Lâappareil ne doit pas produire de brouillage. 2. Lâappareil doit accepter tout
brouillage radioĂŠlectrique subi, mĂŞme si le brouillage est susceptible dâen compromettre le fonctionnement.
Š 2022, The Chamberlain Group LLC
All Rights Reserved
Tous droits rĂŠservĂŠs
Todos derechos reservados
114-5879-000 TSC ACS Support 877-247-6764

1
GUIDE DâINSTALLATION
DU LECTEUR SMART
Pièces inclusesî:
⢠Lecteur, plaque arrière, plaque murale
⢠Vis mĂŠcaniques n°î6 - QTĂ 2
⢠Vis autotaraudeuses n°î6 - QTĂ 2
⢠Vis hexagonale n°î4-40
⢠Vis Pin-in-Torx n°î4-40
Connexions de câblage
Rouge Alimentation
Noir Terre
Blindage Blindage Terre
Vert DonnĂŠes Wiegand 0
RS485A(+)
Blanc DonnĂŠes Wiegand 1
RS485A(-)
Jaune* ContrĂ´le du signal sonore
Marron* Autoprotection
Bleu* DEL de contrĂ´le verte
Orange* DEL de contrĂ´le rouge
BoĂŽtier simple Clavier
TECHNOLOGIES RF Modèle Modèle
125îkHz, 13,56îMHz et BLE mobile SRDRST SRDRKP
INTENSITĂ 120îmA en moyenne, 170îmA en pointe 145 mA en moyenne, 195 mA en pointe
TENSION 5-16îVCC (NâAPPLIQUEZ JAMAIS PLUS DE 16îV)
TEMPĂRATURE TestĂŠ UL⢠-35° Ă 66°C et EN -40° Ă 70°C et humiditĂŠ de 95%
(TestĂŠ UL⢠-31ËF Ă 150ËF et EN -40Ë Ă 158ËF et humiditĂŠ de 95%)
LONGUEUR DE CĂBLE
Lignes de communication
Wiegandî: 200 pieds - 22îAWG
300 pieds - 20 AWG
500 pieds -18îAWG
OSDP @ 12 VCC et 25ËC (77ËF) = 1000 pieds - Paire torsadĂŠe 22îAWG
REMARQUEî: Nâutilisez PAS le bloc dâalimentation fourni avec le CAPXLV ou le CAPXM pour alimenter directement ce lecteur. Comme il fonctionne sous 24îV,
il serait endommagĂŠ.
REMARQUEî: La DEL de contrĂ´le nâest pas disponible lorsquâil est connectĂŠ Ă un CAPXS.
Outils nĂŠcessaires (non fournis)î:
⢠Tournevis cruciforme
⢠1îpo (25îmm), mèche 1/8îpo
⢠Embout Torx sÊcuritaire T8 (en option pour une meilleure dÊtection
des infractions)
⢠Taraudage n°î6-32 si nĂŠcessaire
A. Installez la plaque murale en mĂŠtal sur le boĂŽtier mural/simple.
⢠Utilisez les vis n° 6 fournies.
B. Câblez le câble au panneau de commande.
C. Fixez le lecteur Ă la plaque murale et installez la vis du lecteur.
⢠Suivez les Êtapes 1 à 3 ci-dessous pour assurer un alignement correct. Installez la
vis n塔4-40 ou la vis Pin-in-Torx en bas.
AVERTISSEMENTî: Ce produit peut vous exposer Ă des produits chimiques, dont le plomb, qui sont
reconnus par lâĂtat de Californie comme provoquant le cancer, des malformations congĂŠnitales ou
dâautres problèmes de reproduction. Pour plus dâinformation, visitez www.P65Warnings.ca.gov
*Ces ďŹls sont uniquement utilisĂŠs en mode Wiegand.
**Toutes les mÊthodes de câblage utilisÊes doivent
ĂŞtre conformes au Code national de lâĂŠlectricitĂŠ,
ANSI/NFPA 70.
Les lecteurs doivent ĂŞtre alimentĂŠs par un panneau
de contrĂ´le dâaccès compatible, homologuĂŠ UL, Ă
puissance limitĂŠe, dâune valeur nominale de 5-16îVCC.
Product specificaties
Merk: | Liftmaster |
Categorie: | Toegangscontrolesysteem |
Model: | SRDRST |
Heb je hulp nodig?
Als je hulp nodig hebt met Liftmaster SRDRST stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Toegangscontrolesysteem Liftmaster

27 Maart 2025
Handleiding Toegangscontrolesysteem
- Toegangscontrolesysteem Bosch
- Toegangscontrolesysteem Honeywell
- Toegangscontrolesysteem Abus
- Toegangscontrolesysteem Acti
- Toegangscontrolesysteem Apc
- Toegangscontrolesysteem Axis
- Toegangscontrolesysteem Burg-Wachter
- Toegangscontrolesysteem Eminent
- Toegangscontrolesysteem EQ-3
- Toegangscontrolesysteem EverFocus
- Toegangscontrolesysteem GeoVision
- Toegangscontrolesysteem Hikvision
- Toegangscontrolesysteem Iget
- Toegangscontrolesysteem Indexa
- Toegangscontrolesysteem Marmitek
- Toegangscontrolesysteem Provision ISR
- Toegangscontrolesysteem Satel
- Toegangscontrolesysteem Velleman
- Toegangscontrolesysteem Viking
- Toegangscontrolesysteem Yale
- Toegangscontrolesysteem Optex
- Toegangscontrolesysteem Steren
- Toegangscontrolesysteem Safescan
- Toegangscontrolesysteem Techly
- Toegangscontrolesysteem DSC
- Toegangscontrolesysteem ASSA ABLOY
- Toegangscontrolesysteem Approx
- Toegangscontrolesysteem Delta Dore
- Toegangscontrolesysteem Chief
- Toegangscontrolesysteem IOGEAR
- Toegangscontrolesysteem Dahua Technology
- Toegangscontrolesysteem EQ3
- Toegangscontrolesysteem ETiger
- Toegangscontrolesysteem Suprema
- Toegangscontrolesysteem Vimar
- Toegangscontrolesysteem Speco Technologies
- Toegangscontrolesysteem HID Identity
- Toegangscontrolesysteem ZKTeco
- Toegangscontrolesysteem Panduit
- Toegangscontrolesysteem ONE Smart Control
- Toegangscontrolesysteem Gewiss
- Toegangscontrolesysteem SOREX
- Toegangscontrolesysteem Atlantis Land
Nieuwste handleidingen voor Toegangscontrolesysteem

1 April 2025

31 Maart 2025

31 Maart 2025

31 Maart 2025

31 Maart 2025

31 Maart 2025

31 Maart 2025

29 Maart 2025

29 Maart 2025

28 Maart 2025