LG CineBeam AI ThinQ HU715QW Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor LG CineBeam AI ThinQ HU715QW (4 pagina's) in de categorie Beamer. Deze handleiding was nuttig voor 56 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling
For safety, wear a pair of work gloves when assembling or performing
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the
in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT O
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
PK-1750918
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
Wardrobe Storage Cabinet
Unassembled Model 1471 or CVD1471
Tennsco LLC., Dickson, TN 37056-1888 • (866) 446-8686
LOAD CAPACITIES PER SHELF LEVEL
36w x 18d 200 lbs.
UNIT SIZE WEIGHT CAPACITY
EVENLY DISTRIBUTED
ASSEMBLY OF 1471 or CVD1471 CABINET
Tools Needed: A free 11/ ” nut driver is included with each Tennsco cabinet. 32
Two people are recommended for assembly. Approximate assembly time: 20-30 minutes.
2. Place the cabinet back (Ref. No. 1) on a
protected surface to prevent
scratching the paint.
The ange on the
bottom of the back
should be facing upward.
1. The reference numbers used throughout this sheet refer
to the illustration on the back cover. This is to help you
to identify the various parts as they are mentioned.
3. Attach the left side (Ref. No. 2) to the back by placing
ange (A) around the back and bolting together with
seven bolts and nuts (Ref. Nos. 19 & 20). Be sure that the
lances on all shelf adjustment strips (B) are pointing in the
same direction.
5. Insert the shelf (Ref. No. 4) into
the second lance of the side
and back panels.
6. Attach the top (Ref. No. 5) to the unit by sliding the outer ange
over the back of the unit and the side ange of the side panel on
the unit. The threaded studs should go through
the holes in the top lange of the side and
fasten with three nuts. Attach the back
to the top using four bolts
and nuts.
4. Attach the right side (Ref. No. 3) to the back in the same
manner as you did in step 3, again, making sure that
the ange is around the back and that the lances on the
shelf adjustment strips are pointed in the same direction
as those on the back and left side. 8. Place the rear ange of the bottom (Ref. No. 7) into the
bottom lances of the back. The ange with two holes should
face the front, hanging over the sill. Insert the bolts through
the bottom and still with the head
facing the front of the unit.
Secure with two nuts.
Tighten all bolts.
All lances point UP on
both backs and side.
Flange goes
under back.
Flange faces upward.
Flanges
face upward
Slide ends in to the slots
on the bottom of the sides.
Nuts placed loosely
on studs of the sill.
Insert bottom into
bottom lances.
B
A
NOTE: When bolting the unit together, leave
the bolts slightly loose until Step 8, unless
otherwise specified.
NOTE: All illustrations show a solid door. Assembly
for C-Thru doors (CVD1471) is identical.
Two holes must
be in front
Inset A
Use 2nd
lance
7. Next, attach the sill (Ref. No. 6) to the sides, as shown above.
Place nuts loosely on each of the studs and slide the ends of the
sill into the slots on both sides of the unit. Then, securely tighten
the nuts.
10. Attach the left door
(Ref. No. 8) to the
unit by placing the
door on the hinges,
aligning the hinge
holes, and dropping
the hinge pins (Ref.
No. 15) into the slots.
Then, tap the top of
each hinge pin until
fully seated.
Leveler
Access Holes
9. Using two people, set the unit
upright and attach the left coat
rod bracket (Ref. No. 17) beneath
the left side of the cabinet shelf
by inserting one bolt through the
hole in the left edge of the shelf.
Secure with a nut. Attach the right
bracket in the same way. Then
slide the coat rod (Ref. No. 16)
through the holes in the brackets.
12. The cabinet must be
level in order for the
doors to close
properly. Levelers
may be adjusted by
placing the nut driver
through the hole in
each end of the sill
and adjusting the
leveling screw.
11. Attach the right door
(Ref. No. 9) to the unit
in the same way you
attached the left door.
1. Place the locking handle
(Ref. No. 11) on the right
hand door and fasten with
two #8-32 X 1/ 4hex-head
bolts and lock washers,
provided with the handle.
2. Turn the handle to the
open position and
place the locking cam
(Ref. No. 12) over the
square shank of the
door handle. The latch
must be facing downward
as shown. Then place the
locking cotter pin (Ref. No.
13) through the hole of the
square shank.
3. With the handle still in the open position, hook the
locking bars (Ref. No. 10) to the locking cam (see
“A” at left). Once in position, slowly rotate the door
handle to the closed position so the lock bars
prot rude from the holes at the top and bottom
of the door (shown at right, below).
4. Slide the nylon lock bar
guide inserts (Ref. No.
14) over the lock bar
ends and through the
door slots (see “B” at
right). Push down rmly
until the guides snap
into place.
Handle/Locking System Installation
A
B
B
Product specificaties
| Merk: | LG |
| Categorie: | Beamer |
| Model: | CineBeam AI ThinQ HU715QW |
Heb je hulp nodig?
Als je hulp nodig hebt met LG CineBeam AI ThinQ HU715QW stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Beamer LG
4 November 2024
3 Oktober 2024
13 Maart 2024
6 Juli 2023
3 Juli 2023
2 Juli 2023
23 Mei 2023
8 Mei 2023
7 Mei 2023
3 Mei 2023
Handleiding Beamer
- Beamer Philips
- Beamer HP
- Beamer Sony
- Beamer Samsung
- Beamer Xiaomi
- Beamer Casio
- Beamer Panasonic
- Beamer Epson
- Beamer Asus
- Beamer Canon
- Beamer JVC
- Beamer Medion
- Beamer Toshiba
- Beamer Yamaha
- Beamer Acco
- Beamer Acer
- Beamer Aiptek
- Beamer Anker
- Beamer ASK Proxima
- Beamer Auna
- Beamer Barco
- Beamer Bauer
- Beamer BenQ
- Beamer Blaupunkt
- Beamer D-Link
- Beamer Dell
- Beamer Easymaxx
- Beamer Eiki
- Beamer Elmo
- Beamer Emtec
- Beamer GPX
- Beamer Hama
- Beamer Hisense
- Beamer Hitachi
- Beamer Ibm
- Beamer InFocus
- Beamer Ion
- Beamer Klarstein
- Beamer Kodak
- Beamer Kogan
- Beamer La Vague
- Beamer Leica
- Beamer Lenco
- Beamer Lenovo
- Beamer Livoo
- Beamer Marantz
- Beamer Maxell
- Beamer Mitsubishi
- Beamer Nebula
- Beamer Nec
- Beamer PLUS
- Beamer Polaroid
- Beamer Pyle
- Beamer RCA
- Beamer Reflecta
- Beamer Renkforce
- Beamer Ricoh
- Beamer Salora
- Beamer Sanyo
- Beamer Sharp
- Beamer Showtec
- Beamer Smart
- Beamer Smartwares
- Beamer Speaka
- Beamer Steinel
- Beamer Technaxx
- Beamer Viewsonic
- Beamer Vivitek
- Beamer Vogels
- Beamer XGIMI
- Beamer ZTE
- Beamer Odys
- Beamer OK
- Beamer Oki
- Beamer Optoma
- Beamer Overmax
- Beamer 3M
- Beamer Krüger And Matz
- Beamer Naxa
- Beamer Steren
- Beamer Eurolite
- Beamer Prixton
- Beamer Planar
- Beamer Dukane
- Beamer Yaber
- Beamer Mimio
- Beamer Da-Lite
- Beamer Adj
- Beamer Dahua Technology
- Beamer Derksen
- Beamer Celly
- Beamer Promethean
- Beamer Stairville
- Beamer Laserworld
- Beamer Beghelli
- Beamer Cameo
- Beamer Tzumi
- Beamer EKO
- Beamer MicroVision
- Beamer Elite Screens
- Beamer Celexon
- Beamer Fun Generation
- Beamer Christie
- Beamer Futurelight
- Beamer Varytec
- Beamer Ultimea
- Beamer Dream Vision
- Beamer Knoll
- Beamer DTS
- Beamer Touchjet
- Beamer Boxlight
- Beamer AAXA Technologies
- Beamer Miroir
- Beamer Vankyo
- Beamer AWOL Vision
- Beamer Smart Tech
- Beamer Atlantis Land
- Beamer KickAss
- Beamer Microtek
- Beamer VAVA
- Beamer Panamorph
Nieuwste handleidingen voor Beamer
3 November 2024
3 November 2024
23 Oktober 2024
21 Oktober 2024
21 Oktober 2024
21 Oktober 2024
20 Oktober 2024
20 Oktober 2024
20 Oktober 2024
20 Oktober 2024