LG 42LS679C Handleiding

LG Niet gecategoriseerd 42LS679C

Lees hieronder de 📖 handleiding in het Nederlandse voor LG 42LS679C (53 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 201 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/53
Printed in KoreaP/NO : MFL67360740 (1209-REV00)
CHASSIS : LD21B
MODEL : 42LS679C 42LS679C-ZC
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
LED LCD TV
SERVICE MANUAL
North/Latin America http://aic.lgservice.com
Europe/Africa http://eic.lgservice.com
Asia/Oceania http://biz.lgservice.com
Internal Use Only
- 2 - LGE Internal Use OnlyCopyright © LG Electronics. Inc. All rights reserved.
Only for training and service purposes
CONTENTS
CONTENTS .............................................................................................. 2
SAFETY PRECAUTIONS ........................................................................ 3
SERVICING PRECAUTIONS ................................................................... 4
SPECIFICATION ...................................................................................... 6
ADJUSTMENT INSTRUCTION ............................................................. 11
SCREW ASSEMBLY WORKING GUIDE .............................................. 16
BLOCK DIAGRAM ................................................................................. 17
EXPLODED VIEW .................................................................................. 18
SCHEMATIC CIRCUIT DIAGRAM ..............................................................
- 3 - LGE Internal Use OnlyCopyright © LG Electronics. Inc. All rights reserved.
Only for training and service purposes
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Exploded View.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC
power line. Use a transformer of adequate power rating as this
protects the technician from accidents resulting in personal injury
from electrical shocks.
It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitry that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this TV receiver is blown,
replace it with the specified.
When replacing a high wattage resistor (Oxide Metal Film Resistor,
over 1 W), keep the resistor 10 mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Before returning the receiver to the customer,
always perform an on the exposed AC leakage current check
metallic parts of the cabinet, such as antennas, terminals, etc., to
be sure the set is safe to operate without damage of electrical
shock.
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
switch in the on position, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1 MΩ and 5.2 MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC voltage
measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
0.5 mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
Leakage Current Hot Check circuit
IMPORTANT SAFETY NOTICE
SAFETY PRECAUTIONS

Product specificaties

Merk: LG
Categorie: Niet gecategoriseerd
Model: 42LS679C

Heb je hulp nodig?

Als je hulp nodig hebt met LG 42LS679C stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd LG

LG

LG LV4265 Handleiding

18 December 2024
LG

LG FM33 Handleiding

18 December 2024
LG

LG LV4665 Handleiding

18 December 2024
LG

LG FM37 Handleiding

17 December 2024
LG

LG W411P Handleiding

9 December 2024
LG

LG V390 Handleiding

9 December 2024
LG

LG AC421P Handleiding

9 December 2024
LG

LG VC8404M Handleiding

9 December 2024
LG

LG LV4285 Handleiding

9 December 2024
LG

LG N21P Handleiding

9 December 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Einhell

Einhell WB 50 Handleiding

30 December 2025
Hisense

Hisense HAF1800D Handleiding

30 December 2025
Eufy

Eufy Outdoor / Indoor Siren Handleiding

30 December 2025
Lenco

Lenco TTA-180TN Handleiding

30 December 2025
Pioneer

Pioneer CA-HR-PSA-EVO.003 Handleiding

30 December 2025
TC Electronic

TC Electronic PLETHORA X1 Handleiding

30 December 2025
Pioneer

Pioneer CA-HM-FOR.004 Handleiding

30 December 2025
Pioneer

Pioneer CA-HR-PSA-EVO.002 Handleiding

30 December 2025
Brennenstuhl

Brennenstuhl Tower Power Handleiding

29 December 2024
Brennenstuhl

Brennenstuhl Eco-Line Handleiding

29 December 2024