Levoit Classic 300 Handleiding

Levoit Luchtbevochtiger Classic 300

Lees hieronder de šŸ“– handleiding in het Nederlandse voor Levoit Classic 300 (2 pagina's) in de categorie Luchtbevochtiger. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Classic 300 Lite Ultrasonic Cool Mist Humidiļ¬er
Product Series: Classic 300
Model: LUH-A603-WUS
Questions or Concerns?
Please contact us Monī˜ŸFri, 9:00 amī˜Ÿ5:00 pm PST/PDT
at or at .support@levoit.com (888) 726-8520
USER MAN UAL SAFETY INFORMATION
ā€¢ Only use the humidiļ¬er as
described in this manual.
ā€¢ Place the humidiļ¬er and cord so
that it will not be knocked over.
ā€¢ Do not place near large pieces of
furniture or in high-traī˜c areas.
ā€¢ When not in use, turn the humidiļ¬er
oī˜œ and disconnect from power by
removing the plug from the outlet.
ā€¢ Do not use the humidiļ¬er in wet
environments.
ā€¢ Keep the humidiļ¬er out of reach
from children.
ā€¢ Do not open the base or remove
the water level sensor for self-
servicing.
ā€¢ Always unplug your humidiļ¬er from
the power outlet before cleaning
your humidiļ¬er or detaching the
water tank from the humidiļ¬er base.
ā€¢ Always make sure to place the
humidiļ¬er on a ļ¬‚at, level surface
before operation.
ā€¢ Only ļ¬ll the water tank with clean
water. ļ¬ll the water tank with Never
any other liquids.
ā€¢ Do not place the humidiļ¬er near
sources of heat, such as stovetops,
ovens, or radiators.
ā€¢ Do not place the humidiļ¬er directly
on ļ¬‚oors, carpets, or rugs.
To reduce the risk of ļ¬re, electric shock, or other injury, follow all instructions
and safety guidelines.
General Safety
ā€¢ Do not use other items as
replacement parts for this
humidiļ¬er.
ā€¢ Do not cover the nozzle while
the humidiļ¬er is on. Doing so may
damage the humidiļ¬er.
ā€¢ Remove the water tank from the
base before moving the humidiļ¬er.
ā€¢ Do not immerse the humidiļ¬er
base, power cord, or plug in water.
ā€¢ If the humidiļ¬er is damaged or is
not functioning properly, stop using
it and contact Customer Support
immediately (see page 10).
ā€¢ Supervise children when they are
near the humidiļ¬er.
ā€¢ Children should not clean or
perform maintenance on the
humidiļ¬er without supervision.
ā€¢ Children should be supervised to
ensure that they do not play with
the humidiļ¬er.
ā€¢ This humidiļ¬er is not to be used
by persons (including children)
with reduced physical, sensory,
or mental capacities, or lack of
experience and knowledge, unless
they have been given supervision
or instruction concerning the
use of the appliance by a person
responsible for the safety.
ā€¢ Household use . Not for only
commercial use.
READ AND SAVE THESE
INSTRUCTIONS
Power & Cord
ā€¢ Ensure that the plug ļ¬ts properly
into a polarized socket.
ā€¢ Do not handle the power cord or
plug with wet hands. Keep the plug
and power cord away from liquids.
ā€¢ Your humidiļ¬er has a polarized
plug (one prong is wider than the
other), which ļ¬ts into a polarized
outlet only one way. This is a
safety feature to reduce the risk of
electric shock. If the plug does not
ļ¬t, reverse the plug. If it still does
not ļ¬t, use the plug in that do not
outlet. Do not bypass this safety
feature.
ā€¢ If the power supply cord is
damaged, it must be replaced by
Arovast Corporation or similarly
qualiļ¬ed persons in order to avoid
an electric or ļ¬re hazard. Please
contact Customer Support.
SAFETY INFORMATION (CONT.)
Do not add essential oils or
supplemental water treatment
liquids into the water tank
or base chamber. This will
damage the humidiļ¬er and
cause leaks.
Caution: Risk of Leaks
and Electric Shock 1 ƗUltrasonic Humidiļ¬er
2 ƗWater Filter Sponge (1 Pre-Installed)
1 ƗCleaning Brush
1 ƗUser Manual
Specifications
Package Contents
Power Supply AC 120V, 60Hz
Rated Power 25W
Water Tank
Capacity 1.58 gal / 6 L
Max Run Time
Up to 60 hours on
minimum mist setting
Note: The humidiļ¬er may
run for a longer or shorter
time depending on the
environmental temperature
and humidity.
Noise Level ā‰¤ 30dB
Eī˜Ÿective
Range 215ā€“505 ftī˜™ / 20ā€“47 mī˜™
Dimensions 9.7 x 8.1 x 13.4 in /
24.5 x 20.5 x 34 cm
Weight 4.2 lb / 1.9 kg
GETTING TO KNOW YOUR HUMIDIFIER
AB
LW
X
J
K
I
D
M
N
F
H
G
E
C
S
T
O
P
Q
R
Water tank, upside down
UV
A. Nozzle
B. Water Tank Cover
C. Dust Cover
D. Mist Tube
E. Water Tank
F. Base
G. Reļ¬ll Indicator Light
H. Control Knob
I. Max Water Line (Tank)
J. Water Tank Handles
K. Water Filter
L. Power Cord
M. Float
N. Float Brackets
O. Max Water Line (Base)
P. Secondary Float
Q. Transducer
R. Air Outlet
S. Air Inlet
T. Feet
U. Water Outlet Valve Assembly
V. Water Outlet Valve
W. Noise Silencer
X. Cleaning Brush
C O N TR O L S
Control Knob
ā€¢ Rotate clockwise to turn on the
humidiļ¬er and to adjust the mist level.
ā€¢ Rotate counterclockwise to turn oī˜œ the
humidiļ¬er.
Reļ¬ll Indicator Light
ā€¢ The red light turns on when the water
tank is empty. Reļ¬ll the water tank (see
page 5).
ā€¢ The red light turns oī˜œ when the water
tank is ļ¬lled.
Note:
There is a clicking sound when the
humidiļ¬er turns on/oī˜ž.
GETTING S TARTE D
1. Remove all packaging. Take the water
tank oī˜œ of the base and remove all tape.
2. Clean the humidiļ¬er before ļ¬rst use (see
page 7).
3. Choose a hard, ļ¬‚at location for the
humidiļ¬er at least 12 inches / 30 cm
away from any walls. The surface must
be water-resistant. [
Figure 1.2
]
4. Mist should be directed away from walls,
furniture, bedding, and appliances.
Figure 1.2
Figure 1.1
12 in /
30 cm
12 in /
30 cm
Note:
Check to make sure that the water
ļ¬lter is correctly in place. If not, then rotate
the ļ¬lter clockwise to secure it in place.
[Figure 1.1]
Filling & Refilling
1. Remove the water tank cover. Use
the handles to remove the tank from
the base. Fill the tank with room-
temperature water. [
Figure 1.3
]
Figure 1.3
Note:
ā€¢ We recommend using puriļ¬ed or distilled
water to ļ¬ll the tank.
ā€¢ Do not ļ¬ll past the tankā€™s max water line.
Figure 1.4
2. Replace the water tank cover and place
the tank back on the base. [
Figure 1.4
]
2 3 4 5
Figure 1.5
Figure 1.6
ā€¢ Do not add water directly into the
base chamber. [
Figure 1.5
]
ā€¢ Do not add water through the mist
tube. [
Figure 1.6
]
ā€¢ Do not add essential oils or
supplemental water treatment liquids
into the humidiļ¬er.
ā€¢ Do not use third-party water ļ¬lters.
CAUTION
US I N G YOU R H U MI D I F I E R
1. Rotate the Control Knob clockwise to turn
the humidiļ¬er on. Adjust the knob to your
desired mist level.
2. Rotate the nozzle to adjust the direction of
the mist. [
Figure 2.1
]
3. When your room has reached your
preferred humidity level, turn the
humidiļ¬er to a lower setting, or turn it oī˜œ.
4. Rotate the Control Knob counterclockwise
to turn the humidiļ¬er oī˜œ.
Figure 2.1
Note:
If there is no water in the tank or the tank is
removed, the humidiļ¬er will stop misting and the
Reļ¬ll Indicator Light will turn on. Reļ¬ll the tank and
place it on the base.
Figure 2.2
Important Tips
Your humidiļ¬er must have the correct level of
water in the base chamber to work properly. If
there is too much water in the base chamber,
the humidiļ¬er cannot create mist.
ā€¢ Only add water to the water tank.
ā€¢ Avoid moving or shaking the humidiļ¬er.
ā€¢ Before moving the humidiļ¬er, turn it oī˜œ,
unplug it, and remove the water tank.
ā€¢ If your humidiļ¬er doesnā€™t produce mist
correctly, check the max water line to
see if there is too much water in the
base chamber. Pour out extra water.
[
Figure 2.2
]
Note:
The max water line is
only
for this
purpose.
Figure 3.1
C A R E & M A I N T E N A N C E
ā€¢ All maintenance should be done on a
water-resistant surface.
ā€¢ Change the water daily to avoid
bacteria growth.
ā€¢ Use a tissue or cloth to clean the nozzle
regularly.
ā€¢ If not using the humidiļ¬er for 3 days or
longer, leave water inside.do not
Note:
When pouring out water, hold down the
ļ¬‚oat to ensure that it does not fall out of the
base chamber.
Note:
ā€¢
Never
immerse the base in water or liquid.
Do not
place any part of the humidiļ¬er in a
dishwasher.
ā€¢
Do not
use detergents to clean the humidiļ¬er.
Cleaning
You should clean your humidiļ¬er every
3 days, and when youā€™re ready to store it.
1. Unplug the humidiļ¬er. Remove and
rinse the water tank cover and dust
cover. [
Figure 3.1
]
2. Remove the water tank and pour out
any water from the tank and base
chamber.
Figure 3.2
3. Remove the water ļ¬lter from the tank by
rotating it counterclockwise. [
Figure 3.2
]
4. Rinse the tank, water ļ¬lter, and base
chamber with room temperature water.
Descaling Your Humidifier
Figure 3.3
Figure 3.4
Figure 3.5
Figure 3.6 Figure 3.7
Reassembling
1. Flip the water tank over and place the
noise silencer back into the tank.
2. Place the water ļ¬lter back into the tank
and rotate it clockwise to secure it in
place.
3. Place the ļ¬‚oat back into the base
chamber:
a. Make sure the correct side of the
ļ¬‚oat is facing up.
b. Insert the smaller prong into the
closed side of the ļ¬‚oat brackets.
[
Figure 3.8
]
c. Place the larger prong into the
open (U-shaped) side of the ļ¬‚oat
brackets.
4. Place the tank on the base and place
the cover on top.
Figure 3.8
Storing
Follow the cleaning instructions (see page 7)
and allow all parts to dry completely before
storing. Store in a cool, dry location.
FE DE RA L C O MMU N IC AT I O N C O M MIS SI O N IN T ER F ER EN C E STATE ME NT ā€“ PA R T 1 8
This device complies with part 18 of the FCC Rules.
This equipment generates and uses ISM frequency energy and if not installed and used properly, that is in strict
accordance with the manufacturerā€™s instructions, may cause interference to radio and television reception. It has been
type tested and found to comply with limits for an ISM Equipment pursuant to part 18 of FCC Rules, which are designed
to provide reasonable protection against such interference in a residential installation. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause interference to radio or television
reception, which can be determined by tuning the equipment oī˜œ and on, the user is encouraged to try to correct the
interference by one or more of the following:
ā€¢ Reorient the receiving antenna of radio or television.
ā€¢ Relocate the equipment with respect to the receiver.
ā€¢ Move the equipment away from the receiver.
ā€¢ Plug the equipment into a diī˜œerent outlet so that the equipment and receiver are on diī˜œerent branch circuits.
Conduct only the user maintenance found in this manual. Other maintenance and servicing can cause harmful interference
and can void the required FCC compliance. The manufacturer is not responsible for any radio or TV interference cause by
unauthorized modiļ¬cation to the equipment. It is the responsibility of the user to correct such interference.
Terms & Policy
Arovast Corporation (ā€œArovastā€) warrants this
product to the original purchaser to be free from
defects in material and workmanship, under
normal use and conditions, for a period of 2 years
from the date of original purchase.
Arovast agrees, at our option during the
warranty period, to repair any defect in material
or workmanship or furnish an equal product in
exchange without charge, subject to veriļ¬cation
of the defect or malfunction and proof of the date
of purchase.
There is no other express warranty. This warranty
does not apply:
ā€¢ If the product has been modiļ¬ed from its
original condition;
ā€¢ If the product has not been used in
accordance with directions and instructions
in the user manual;
ā€¢ To damages or defects caused by accident,
abuse, misuse or improper or inadequate
maintenance;
ā€¢ To damages or defects caused by service
or repair of the product performed by an
unauthorized service provider or by anyone
other than Arovast;
ā€¢ To damages or defects occurring during
commercial use, rental use, or any use for
which the product is not intended;
ā€¢ To damages or defects exceeding the cost
of the product.
Arovast will not be liable for indirect, incidental,
or consequential damages in connection with the
use of the product covered by this warranty.
This warranty extends only to the original
consumer purchaser of the product and is
not transferable to any subsequent owner
of the product regardless of whether the
product is transferred during the speciļ¬ed
term of the warranty.
This warranty does not extend to products
purchased from unauthorized sellers. Arovastā€™s
warranty extends only to products purchased
from authorized sellers that are subject to
Arovastā€™s quality controls and have agreed to
follow its quality controls.
All implied warranties are limited to the period of
this limited warranty.
This warranty gives you speciļ¬c legal rights
and you may also have other rights which
vary from state to state. Some states do not
allow the exclusion or limitation of incidental
or consequential damages, so the above
limitation or exclusion may not apply to you.
If you discover that your product is
defective within the speciļ¬ed warranty
period, please contact Customer Support
via . dispose support@levoit.com DO NOT
of your product before contacting us. Once
our Customer Support Team has approved
your request, please return the product
with a copy of the invoice and order ID.
Every Levoit product automatically includes a
2-year warranty. To make the customer support
process quick and easy, register your product
online at www.levoit.com/warranty.
This warranty is made by:
Arovast Corporation
1202 N. Miller St., Suite A
Anaheim, CA 92806
Product Classic 300 Lite Ultrasonic
Cool Mist Humidiļ¬er
Model LUH-A603-WUS
For your own reference, we strongly recommend
that you record your order ID and date of purchase.
Date of Purchase
Order ID
WA R R A N T Y I N F O R M ATI O N
CU S TO M E R S U P P O R T
If you have any questions or concerns
about your new product, please contact our
helpful Customer Support Team.
Arovast Corporation
1202 N. Miller St., Suite A
Anaheim, CA 92806
Email: support@levoit.com
Toll-Free: ī˜˜888ī˜— 726ī˜–8520
Monī˜ŸFri, 9:00 amī˜Ÿ5:00 pm PST/PDT
Support Hours
*Please have your order invoice and order ID
ready before contacting Customer Support.
A1-01.00_D_22A06_us
76 8 9 10
1. Remove the water ļ¬lter from the tank by
rotating it counterclockwise.
2. Fill the tank with 3 US cups / 710 mL of
distilled white vinegar.
3. Replace the tank cover and swish the
vinegar around the tank. [
Figure 3.3
]
4. Place the tank on the base and soak for
15ā€“20 minutes. Vinegar will drain into
the base chamber and loosen scale
(mineral buildup). [
Figure 3.4
]
5. Pour out any vinegar and ļ¬‚ip the tank
over. Remove the noise silencer by
pressing the release tab and gently
pulling it oī˜œ. [
Figure 3.5
]
6. Remove the ļ¬‚oat from the base
chamber by pulling up the larger side
of the ļ¬‚oat [
Figure 3.6
] and pulling the
shaft out from the ļ¬‚oat brackets. One
side of the brackets is open (U-shaped)
to allow removal. [
Figure 3.7
]
7. Place the ļ¬‚oat, water ļ¬lter, and noise
silencer in a container. Fill with enough
vinegar to cover them. Soak for 15ā€“20
minutes.
8. Use the cleaning brush and a soft cloth
to remove scale from all parts.
9. Rinse all parts until any vinegar smell is
completely gone.
10. Completely dry all parts with a cloth
before reassembling.
Problem Possible Solution
Little or no mist
comes out.
Turn the mist level to a higher setting.
There may be too much water in the base chamber. Empty the base chamber.
Reļ¬ll the water tank (not the base chamber) and place the water tank properly
onto the base.
Make sure the air inlet on the bottom of the base is not blocked. The humidiļ¬er
should not be set on carpet or other surfaces that may block the air inlet.
Make sure the nozzle is not blocked or clogged.
Humidiļ¬er produces
an unusual smell.
If the humidiļ¬er is new, unplug and rinse all parts, then place in a cool, dry place
for 12 hours.
Clean the water tank and base chamber (see , page 6).Care & Maintenance
Condensation forms
around humidiļ¬er or
windows.
Humidity may be too high. Turn down the mist level, turn oī˜œ the humidiļ¬er, or
open a door or window in the room.
Mold grows inside
the humidiļ¬er.
Clean the water tank and base chamber regularly (see , Care & Maintenance
page 6).
Reļ¬ll Indicator Light
turns on.
Fill the water tank.
Place the water tank properly on the base.
Clean the water ļ¬lter (see page 7) or replace it with a new one. To request a
new water ļ¬lter, contact (see page 10). Customer Support
T R O U B L E S H O O T I N G
FC C SD O C S UP PL I ER ā€™ S DE CL A R AT I O N O F CO N F O R MI T Y
Arovast Corporation hereby declares that this equipment is in compliance with the FCC Part 18 Subpart B. The declaration of
conformity may be consulted in the support section of our Web site, accessible from www.levoit.com


Product specificaties

Merk: Levoit
Categorie: Luchtbevochtiger
Model: Classic 300

Heb je hulp nodig?

Als je hulp nodig hebt met Levoit Classic 300 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Luchtbevochtiger Levoit

Handleiding Luchtbevochtiger

Nieuwste handleidingen voor Luchtbevochtiger