LevelOne PLI-2040 Handleiding

LevelOne Powerline adapter PLI-2040

Lees hieronder de 📖 handleiding in het Nederlandse voor LevelOne PLI-2040 (8 pagina's) in de categorie Powerline adapter. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

LevelOne

PLI- 2040

200Mbps HomePlug AV Adapter

User Manual

V1.1

HomePlug PowerLine

HomePlug PowerLine is an excellent solution that can be used to extend your network. In the home or small oﬃce

building, use HomePlug Ethernet Bridge Adapters to link multiple locations without the need to run Ethernet cable.

Combined with a broadband DSL/Cable connection, every room with electrical power outlets will have easy access

to high-speed Internet connection.

Introduction

200Mbps HomePlug AV Adapter allows you to connect any device which has an Ethernet port to a PowerLine net-

work. In operation, the HomePlug AV Adapter is completely transparent, and simply passes data between 200Mbps

the Ethernet port and the PowerLine network. The PowerLine data transfer rate can reach be ed up to 200Mbps.

Any device may be connected to the HomePlug Ethernet Bridge s Ethernet port, but a Windows PC must 200Mbps ’

be used for conﬁguration.

* Strongly recommend Windows 2000/XP/Vista for utility conﬁgurati /7 on

Physical Details

Figure 1 Mbps HomePlug AV Adapter : 200

Front Panel LEDs

Power

On - Normal operation.

Off - No power

Sleep - blanking

HomePlug

On - The PowerLine network is active. This means that at least one other HomePlug de-

vice was detected.

Off - PowerLine network is not available - HomePlug devices were detected. no other

Flashing - Data is being transmitted or received via the PowerLine network.

Ethernet

On - Ethernet connection is active.

Off - No Ethernet connectio n.

Flashing - Data is being transmitted or received via the Ethernet Port.

LED Link quality (Data PHY Rate)

Green:100 ~ (good link quality) Mbps

Orange:50~99Mbps

Red: less 50Mbps (bad link quality)

Setup

Conﬁguration requires the use of Windows PC. Once conﬁgured, any device may be connected to the 200Mbps

HomePlug AV Adapter's Ethernet port. To perform conﬁguration, follow procedures list below. the

1. 200 Connect a standard LAN cable from the Mbps HomePlug AV Adapter's Ethernet port to your PC.

2. 200 Plug the Mbps HomePlug AV Adapter into a power outlet.

3. Wait a few seconds for startup to be completed, and then check the LEDs

 The LED should be ON. Power

 The LED will be ON if other HomePlug devices are detected, otherwise it will be OFF. HomePlug

 The LED should be ON. Ethernet

4. Insert the supplied CD-ROM into your Windows PC, and wait for it to start, select Utility“ ” from the autorun

screen. If it does not start automatically, locate and run SETUP.EXE.

5. Follow the prompts to install the utility. PLI-2040

Product specificaties

Merk:	LevelOne
Categorie:	Powerline adapter
Model:	PLI-2040
Kleur van het product:	Wit
Breedte:	70 mm
Diepte:	96 mm
Hoogte:	32 mm
Connectiviteitstechnologie:	Bedraad
Interface:	Ethernet
Voldoet aan industriestandaarden:	IEEE802.3; IEEE802.3u
Temperatuur bij opslag:	-20 - 70 °C
Intern:	Nee
Compatibele besturingssystemen:	Windows 2000/ME/NT/XP/Vista/7
Frequentiebereik:	0.002 - 0.028 GHz
Hostinterface:	RJ-45
Maximale overdrachtssnelheid van gegevens:	200 Mbit/s
Relatieve luchtvochtigheid bij opslag (geen condensering):	10 - 90 procent
Link/Act LED:	Ja
Bedrijfstemperatuur (T-T):	0 - 40 °C
Aantal poorten:	1