Leisure LX155 Handleiding

Leisure Spoelbak LX155

Lees hieronder de 📖 handleiding in het Nederlandse voor Leisure LX155 (2 pagina's) in de categorie Spoelbak. Deze handleiding was nuttig voor 41 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

1821-02

Luxe Inset Sinks Fitting Instructions

1. It is recommended that the Inset sink is tted to the

worktop before being permanently xed to the cabi-

net.

2. Place the sink upside down on worktop. Position the

sink relative to the worktop as required, ensuring that

the cabinet framework will be clear of all parts of the

sink.

With sharp soft pencil draw round sink as accurately

as possible. See g. 1.

3. Remove the sink and draw another line 10mm inside

the outline of the sink top following the corner radii

with care. This is the cutting line for the aperture.

Fig. 1

Fig. 3

4. Drill as large a hole as possible inside the cutting line.

Using a pad saw, jig saw or similar, cut out the aperture

to the cutting line.

5. Remove paper backing from the foam tape and stick

down to the worktop, lining up the inner edge of the

tape 3 to 4mm from the edge of the cut, see g. 2. A

neat butt joint of the two ends is desirable. The tape

may be stretched slightly to obtain this. The worktop

should be clean and dry before application.

6. Attach the xing clips to the sink rail as shown in

g. 3 ensuring that the two ‘prongs’ of the clip face

inwards.

Open the hinge on the clip.

7. Turn the sink upside down and lay the worktop over

the sink. Swing the clip into position. (This is the most

eective method although if the worktop has been

xed to the cabinet, the sink can be placed in the

aperture and the xing eected from underneath).

8. With the sink secured in position the excess sealing

tape should be cut o by carefully running a sharp

knife or razor blade round the periphery of the sink

and then lifting the excess tape away.

Fig. 2

NB The adjustment of the clamping bracket for U.K. mar-

ket suits worktops of thicknesses 27mm to 43mm.

Any variations from these thicknesses will either

require packing under the clips or for the worktops

to be rebated.

Recommended tightening sequence for sink xing

clips

1821-02

After Care Stainless Sinks

Day to Day Care

Routine cleaning of your stainless steel sink is easy if

the following simple procedure is followed

After use wipe the bowl and drainer with a soft damp

soapy cloth, rinse with clean water. In hard-water ar-

eas, an application of Jif will avoid any build-up of dull

lm of waterborne deposits.

Although stainless steel is an extremely durable mate-

rial and will withstand a great deal of hard use, it can

be scratched by hard or sharp objects. If the surfaces

are to be kept in a blemish free condition reasonable

care should be taken when handling such items.

Discolouration and Heavy Staining

Staining of stainless steel in most cases is due to

something being deposited on the steel rather than

an attack on the material itself. The most common

cause of staining is the build up of a thin lm of water

borne deposits on the sink surface, often rst seen as

a rainbow eect. The build up of such a lm can be

avoided by drying the surface of the sink after use as

described above. However, should such a lm ap-

pear, it can be readily removed with a soft damp cloth

and Jif. To remove the lm, apply the Jif neat and rub

vigorously with a damp cloth along the length of the

sink surface. After cleaning rinse thoroughly with

clean water and dry. Wire wool products and ferrous

water supply pipes can leave minute ferrous particles

adhered to the sink surface. Since stainless steel un-

der normal conditions does not rust, these particles

can cause the appearance of small brown rust stains.

These stains can be removed using the procedure

described above.

CAUTION :

Certain household products contain substances

which will attack the stainless steel surface, they are :

1. Bleaches :

Most common domestic bleaches contain Chlorine in

the form of a hypochlorite. Chlorine attacks the micro-

scopic Chromium Oxide lm on the surface and can

cause pitting of the surface. Bleaches should always

be used in the prescribed strength specied by the

manufacturers. Undiluted bleaches can cause pitting

and staining of the surface and should be immedi-

ately rinsed o with plenty of clean water. All cleaning

agents containing hypochlorites are unsuitable for

use with stainless steel and, even highly diluted, can

cause pitting under certain conditions. For this reason

it is strongly recommended that the sink is not used

for soaking clothes or cleaning clothes in hypochlo-

rite solutions for long periods.

2. Silver Dip Cleaners :

These are particularly harmful since they contain

strong acids which can cause discolouration and pit-

ting. The rst sign of this is an iridescent rainbow stain

which turns an etched dull grey colour. Should any

Silver Dip Cleaner come into contact with the surface

of the sink it should be immediately rinsed o with

plenty of clean water.

3. Corrosive Foodstus :

Fruit juices, damp salt, vinegar, readymade mustards,

pickle and mayonnaise can cause pitting and corro-

sion if left in contact with the stainless steel surface

for long periods.

4. Acids :

Sulphuric, Hydrochloric and other strong acids will

cause pitting corrosion, as will photographic develop-

ing liquids. All should be immediately washed o with

plenty of clean water if contact occurs.

Cleaning :

Always use a soft cloth. The use of coarse grit scour-

ing powders or soap lled wire wool cleaning pads is

not recommended, since both will mark the surface of

the sink. Wire wool pads can leave tiny fragments of

wire embedded in the surface and these can rust and

leave small brown rust stains. Vigorous rubbing with a

soft cloth, JIF, neat detergent, cleaning cream or liquid

will remove these stains. Always remove wet cleaning

aids (cloths, containers, etc.) from the sink surface af-

ter use in order to avoid the formation of water marks

and rust stains.

Meadow Lane, Long Eaton,

Nottingham, NG10 2GD, England

Tel: +44 (0) 115 946 4000 Fax: +44 (0) 115 973 6602

E-mail: consumers@rangemaster.co.uk

www.leis uresinks.co.uk

EN 13310 : 2003

Kitchen sink made of:

Cleanability:

Load resistance:

Durability:

Pass

NPD / N/A

Pass

Stainless Steel

Product specificaties

Merk:	Leisure
Categorie:	Spoelbak
Model:	LX155
Kleur van het product:	Roestvrijstaal
Breedte:	1500 mm
Diepte:	508 mm
Soort wastafel:	Opbouwwasbak
Vorm gootsteen:	Rechthoekig
Materiaal gootsteen:	Roestvrijstaal
Aantal gootstenen:	1 kommen
Vorm eerste spoelbak:	Rechthoekig
Eerste kom dimensies (WxL):	420 x 350 mm
Eerste kom diepte:	190 mm
Kraangat:	Ja
Tap-gat grootte:	35 mm
Aantal kraangaten:	1
Aanrecht:	Ja