Lectrosonics RATPAC Handleiding

Lectrosonics Niet gecategoriseerd RATPAC

Lees hieronder de 📖 handleiding in het Nederlandse voor Lectrosonics RATPAC (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 41 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

RATPAC

Connector Kit

INSTRUCTION MANUAL

Rio Rancho, NM, USA

www.lectrosonics.com

Fill in for your records:

Serial Number:

Purchase Date:

Build a right angle TA5 or TA3 connector.

MODEL#

LECTROSONICS, INC.

Parts Description and Details

The RATPAC (Right Angle T connector PACkage) is a

versatile kit for building a right angle connector for use

with the SR receiver or Lectrosonics transmitters. The

3-pin conﬁguration is normally used for the rear panel

audio outputs of the SR receiver. The 5-pin conﬁgura-

tion is the standard connector for most belt pack trans-

mitters and the front panel outputs on the 5P version

of the SR receiver.

The kit includes a standard TA5F connector, a 3-pin in-

sert, modiﬁed cable clamp, modiﬁed backshell, tubing,

set screws with wrench, and a machined aluminum

right angle housing.

TA3F

Modiﬁed

TA5F parts

Spare set screw and

wrench included

The right angle housing is a unique machined alumi-

num part that adapts a TA Series connector to work

with a range of cable sizes and 3-pin or 5-pin inserts.

Keyway to

prevent cable

clamp from

turning

Threaded

hole for set

screw

A standard TA connector sleeve is used with either a

3-pin or 5-pin insert and a modiﬁed cable clamp. The

insert nests inside the sleeve and is held in place by a

spacer and metal retainer. The sleeve is held in place

by two set screws in the machined aluminum housing.

The shrink tubing can be used wherever it is useful to

provide an additional strain relief. Cable is not included

in the kit and is shown only to illustrate the use of the

large and small silicon tubing.

Connector

sleeve

3-pin/5-pin

insert

Plastic

spacer

Metal

retainer

Right angle

housing

Set

screws

Allen

wrench

Standard

cable

clamp

Modiﬁed

backshell

Large

silicon

tubing

Standard

backshell

Small

silicon

tubing

Shrink

tubing

The tab on the cable

clamp nests into the

keyway on the right

angle housing

Completed connector

with larger cable.

Completed connector

with smaller cable.

Assembly

The example shown here illustrates an assembly with

a larger cable and 3-pin insert, which could be used

with the SREXT rear panel on the SR receiver.

Model Description

Rio Rancho, NM 3

IMPORTANT: Connect the cable into the receiver

or microphone and make sure it is working before

crimping the cable clamp.

Slide the cable clamp into the hous-

ing, making sure the tab seats in the

keyway on the housing. Gently push

the cable into the housing to leave a

little slack in the wires before crimp-

ing.

DO NOT ROTATE THE

CONNECTOR SLEEVE MORE

THAN 90 DEGREES IN TRYING

TO ORIENT THE CABLE EXIT

DIRECTION.

Step 6

Crimp the tabs on the cable clamp.

If it is necessary to ground the

housing to the cable, use the

smaller cable clamp tabs to grab the

cable shield. The larger tabs should

always go over the cable insulation and the tubing to

keep the insulation from working up the cable. The

housing will normally ground to the transmitter case

through the retainer, but some lavalieres really like to

have the cable clamp tabs grab the shield for better RF

rejection.

Step 7

Slide the backshell over the clamp and thread it onto

the housing.

Smaller

crimping tabs

Larger

crimping tabs

Silicon

tubing

Backshell

(modiﬁed or standard)

Metal

retainer

Plastic

spacer

Insert

(3-pin or 5-pin)

Connector

sleeve

Tab in keyway

NOTE: Larger silicon tubing is normally positioned over

the cable clamp after it is crimped. Smaller silicon tubing is

normally positioned under the cable clamp before it is crimped.

Also see Step 6 below about grounding of some lavaliere mics.

Step 1

Install the set screws into the right angle housing. Turn

them in a few turns, but do not tighten them. Slide all

the parts onto the cable in the order shown above.

Step 2

Strip the outer insulation of the cable back about 1/2

inch. Strip the insulation on the inner wires back about

1/8 inch.

Step 3

Solder the wires onto the pins on the insert as needed.

For the SR receiver, refer

to its manual for pinouts.

http://www.lectrosonics.

com/manuals/SRman.pdf

For microphones to be

used with Lectrosonics transmitters, refer to the Servo

Bias Mic Wiring document.

http://www.lectrosonics.com/service/ServoBiasWiring.pdf

Step 4

Slide the spacer up, align the ﬂats on it and then attach

it to the insert. Make sure the metal retainer is in posi-

tion on the plastic spacer and slide the assembly into

the connector sleeve. The ﬂats must be aligned with

the black button on the sleeve for the assembly to fully

nest inside the sleeve.

Step 5

Orient the connector sleeve in the desired position

while the cable can freely rotate inside the housing.

Gently slide

the cable and

connector as-

sembly back

through the

housing until

the connector

is seated.

Apply pressure to make sure the connector assembly

is completely seated in the housing. Insert the long

end of the allen wrench and tighten the two set screws

to secure the connector sleeve.

1/2”

1/8”

Shield

Align ﬂats with button

180˚

Product specificaties

Merk:	Lectrosonics
Categorie:	Niet gecategoriseerd
Model:	RATPAC

Heb je hulp nodig?

Als je hulp nodig hebt met Lectrosonics RATPAC stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Lectrosonics

Lectrosonics DBu-LEMO Handleiding

16 November 2023

Lectrosonics RATPAC Handleiding

16 November 2023

Lectrosonics DCHT Handleiding

16 November 2023

Lectrosonics RPS4 Handleiding

16 November 2023

Lectrosonics DHu Handleiding

16 November 2023

Lectrosonics MCAES3 Handleiding

15 November 2023

Lectrosonics ZS-LMB Handleiding

15 November 2023

Lectrosonics SMQV Handleiding

15 November 2023

Lectrosonics UMC16B-A1B1 Handleiding

15 November 2023

Lectrosonics WM Handleiding

15 November 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Inglesina Welcome Pad Handleiding

22 December 2024

Inglesina Front Handleiding

22 December 2024

Inglesina Newborn Winter Muff Handleiding

22 December 2024

Inglesina Stroller Winter Muff Handleiding

22 December 2024

Protector AS-5030.3 V2 Handleiding

21 December 2024

Sabrent AU-MMCW Handleiding

21 December 2024

Sabrent AU-2X35 Handleiding

21 December 2024

Sabrent CB-RS232 Handleiding

21 December 2024

Owon 500W Handleiding

21 December 2024

Owon 300W Handleiding

21 December 2024