Lancom 883+ VoIP Handleiding

Lancom Niet gecategoriseerd 883+ VoIP

Lees hieronder de 📖 handleiding in het Nederlandse voor Lancom 883+ VoIP (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 154 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

M O U N T I N G A N D C O N N E C T I N G T H E D E V I C E

T E C H N I C A L D E T A I L S

Hardware

Power supply 12 V DC, external power adapter (230 V); bayonet connector to secure against disconnection

Power consumption Max. ca. 18 W

Environment Temperature range 0–40 °C; humidity 0–95 %; non-condensing

Housing Robust synthetic housing, rear connectors, ready for wall mounting, Kensington lock; mea-

sures 210 x 45 x 140 mm (W x H x D)

Number of fans One quiet fan

Interfaces

WAN: VDSL2 aVDSL2 as per ITU G.993.2; profiles 8a, 8b, 8c, 8d, 12a, 12b, 17a, 35b

aVDSL2 vectoring as per ITU G.993.5 (G.vector)

aCompatible to VDSL2 from Deutsche Telekom

aVDSL Supervectoring as per ITU G.993.2 (Annex Q)

aCompatible to U-R2 from Deutsche Telekom (1TR112)

aADSL2+ over ISDN as per ITU G.992.5 Annex B/J with DPBO, ITU G.992.3, and ITU G.992.1

aSupports just one virtual connection at a time in ATM (VPI-VCI pair)

Wi-Fi aFrequency band: 2400-2483.5 MHz (ISM) or 5150-5825 MHz (restrictions vary between

countries)

aRadio channels 2.4 GHz: Up to 13 channels, max. 3 non-overlapping (2.4-GHz band)

aRadio channels 5 GHz: Up to 26 non-overlapping channels (channels available vary

according to country regulations; DFS for automatic dynamic channel selection required)

ETH 4 individual ports, 10 / 100 / 1000 Mbps Gigabit Ethernet, by default set to switch mode.

Up to 3 ports can be operated as additional WAN ports. Ethernet ports can be electrically

disabled in the LCOS configuration.

USB USB 2.0 hi-speed host port for connecting USB printers (USB print server),

serial devices (COM-port server) or USB drives (FAT file system)

ISDN 1 / ISDN 2 ISDN 1: Internal (NT) or external (TE) ISDN bus. This feature is controlled by LCOS.

ISDN 2: Internal (NT) ISDN bus.

Analog 1 / Analog 2

Analog 3 / Analog 4

Use the cable of your analog devices to connect them with the analog interfaces. If necessary

use the adapters from the LANCOM Analog Adapter Set.

Config (Com) / V.24 Serial configuration interface/COM-port (8-pin mini-DIN): 9,600 - 115,200 baud, suitable for

optional connection of analog/GPRS modems. Supports internal COM-port server and provides

transparent asynchronous serial-data transfer via TCP.

WAN protocols

VDSL, ADSL, Ethernet PPPoE, PPPoA, IPoA, Multi-PPPoE, ML-PPP, PPTP (PAC or PNS) and IPoE (with or without

DHCP), RIP-1, RIP-2, VLAN

ISDN DSS1 (Euro-ISDN), PPP, X75, HDLC, ML-PPP, V.110/GSM/HSCSD

Declaration of Conformity

Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in

compliance with Directives 2014/30/EU, 2014/53/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006.

The full text of the EU Declaration of Conformity is available at the following Internet address:

www.lancom-systems.com/doc

Package content

Manual Quick Reference Guide (DE/EN); Installation Guide (DE/EN)

Cable 1 DSL cable for an IP-based line, 4.25 m

Adapters 2 TAE adapters (RJ11 - TAE)

Power adapter External power supply adapter (230 V); NEST 12 V / 2 A DC/S; barrel / bayonet (EU),

LANCOM item no. 111303

This product contains separate open-source software components which are subject to their own licenses, in particular

the General Public License (GPL). The license information for the device firmware (LCOS) is available on the device‘s

WEBconfig interface under “Extras > License information“. If the respective license demands, the source files for the

corresponding software components will be made available on a download server upon request.

i VPN

Off VPN connection inactive

Green, permanently VPN connection active

Green, flashing VPN connecting

e ISDN

Off Interface deactivated

Green, permanently D-channel active

Green, flickering ISDN data transfer

Red, flickering ISDN transfer error

Red / orange, blinking ISDN hardware error

b Online

Off WAN connection inactive

Green, permanently WAN connection active

Red, permanently WAN connection error

c DSL

Off Interface deactivated

Green, permanently DSL connection active

Green, flickering DSL data transfer

Red, flickering DSL transfer error

Red / orange, blinking DSL hardware error

Orange, blinking DSL training

Orange, permanently DSL sync

Green, blinking DSL connecting

d Analog

Off Interface deactivated

Green, permanently Interface activated

Orange, blinking Incoming call

Green, blinking Connection active

h VoIP

Off No SIP accounts defined or VCM is off

Green, permanently All defined and active SIP accounts

(outgoing) were successfully registered

Red, permanently Not all defined and active SIP accounts

were registered (possibly still in process)

Red or green,

inverse flashing

Number of currently used lines (connecting

or connected)

f ETH

Off No networking device attached

Green, permanently Connection to network device operational,

no data traffic

Green, flickering Data transmission

g WLAN

Off No Wi-Fi network defined or Wi-Fi module

deactivated. The Wi-Fi module is not

transmitting beacons.

Green, permanently At least one Wi-Fi network is defined and

Wi-Fi module activated. The Wi-Fi module

is transmitting beacons.

Green, blinking DFS scanning or other scan procedure

j Reset

Reset button Operated e.g. with a paper clip

ashort press: Restart the device

along press: Reset the device

a Power

Off Device switched off

Green, permanently* Device operational, resp. device paired /

claimed and LANCOM Management Cloud

(LMC) accessible

Red / green blinking Configuration password not set. Without a

configuration password, the configuration

data in the device is unprotected.

Red blinking Charge or time limit reached

1x green inverse

blinking*

Connection to the LMC active, pairing OK,

device not claimed

2x green inverse

blinking*

Pairing error, resp. LMC activation code

not available

3x green inverse

blinking*

LMC not accessible, resp. communication

error

aVDSL interface

Use the supplied DSL cable for the IP-based line to connect the

VDSL interface and the provider’s telephone socket. For more

infor mation, please contact your Internet service provider.

bEthernet interfaces

Use an Ethernet cable to connect one of the interfaces ETH 1 to

ETH4 to your PC or a LAN switch.

cAnalog interfaces

Connect analog terminal devices to the analog interfaces either

directly via RJ11, or with the help of the enclosed TAE adapters.

Further adapters are optionally available.

dConfiguration interface

Use a serial configuration cable to connect the serial interface

(COM) to the serial interface of the device you want to use for

configuring / monitoring (separately available).

eISDN interfaces

ISDN 1:

Internal (NT) or external (TE) ISDN bus.

This feature is controlled by LCOS.

ISDN 2:

Internal (NT) ISDN bus.

A 100-Ohm resistor for line termination is

switchable in LCOS.

fUSB interface

You can use the USB interface to connect a USB printer or a

USB memory stick.

gPower

After connecting the cable to the device, turn the bayonet

connector 90° clockwise until it clicks into place.

Use only the supplied power adapter.

a b c d e f g

Gigabit Ethernet 10/100/1000

ISDN 1 ISDN 2

TE / NT NT

VDSL

Analog 1/3Analog 2/4

a c eb gfd ih j

LANCOM 883+ VoIP

Quick Reference Guide

C ud eadylo -r

*) The additional power LED statuses are displayed in 5-seconds

rotation if the device is configured to be managed by the LANCOM

Management Cloud.

Please observe the following when setting up the device

A Do not rest any objects on top of the device

A For devices to be operated on the desktop, please attach the

adhesive rubber footpads

AIn case of wall mounting, use the drilling template as supplied

AKeep the ventilation slots on the side of the device clear

of obstruction

ARack installation with the optional LANCOM Rack Mount

(separately available)

LANCOM 1681V

Power

VDSL

Onl ine

ETH 1

VPN

TH 3

ETH 4

Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!

Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.

LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This docu-

ment contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and / or omissions. 111906/11/21