Labelmate MC-11+ Handleiding

Labelmate Labelprinter MC-11+

Lees hieronder de 📖 handleiding in het Nederlandse voor Labelmate MC-11+ (2 pagina's) in de categorie Labelprinter. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

MAINTENANCE:

Your MC-11+ requires no maintenance

Product Limited Warranty

All Labelmate Products are warranted to the original end-user customer to be free from defects in

materials and workmanship. If it is determined by Labelmate that a product has failed under the terms of

this warranty, the product will be repaired or replaced at no charge to the customer. Labelmate reserves all

rights to determination of coverage and liability under this warranty. The warranty period for all new

Labelmate products is outlined below:

The warranty period for all products starts on the date purchased by the original end-user customer.

Warranty coverage is not transferable with ownership and will terminate immediately upon rental, resale or

any other change in ownership. This warranty does not cover repair to any product which is damaged, has

been modiﬁed, is missing parts, or has been opened or repaired by any unauthorised person. Use of any

unauthorised accessory or attachment will void coverage. Purchase documentation should be retained for

coverage veriﬁcation.

In the event your product requires service, please contact the distributor you bought the product from. The

customer assumes responsibility for all cost and risk incurred in transport for service.

Labelmate makes no other warranty of any kind expressed or implied, or to suitability or ﬁtness for a

particular purpose. No other person, agent or reseller is authorised to give any warranties on behalf of

Labelmate. Any obligation to warranty other than that speciﬁcally addressed above is hereby disclaimed.

Warranty Period

Products Covered

5 years

Label Rewinders

Label Unwinders

3 years

Label Counters (mechanical parts

only)

Label Slitters (mechanical parts

only)

Label Dispensers

Printer Mechanisms

1 year

Power Supply Modules

Counter modules

Encoders

Any products not speciﬁed above.

LLC

69 AVENUE ALPHONSE XIII, 1180 BRUSSELS, BELGIUM

TEL: +322.375.69.60 FAX: +322.375.38.96 –

brussels@labelmate.com

www.labelmateeurope.com

MINI-CAT Label Rewinder with Adjustable Core Holder

 Switched Bi-Directional Control.

 Build-in Speed/Torque Control

 Standard External Control

 Constant Adjustable Torque™

"CAT" Technology.

Remove all parts from the shipping container and verify contents.

PACKAGE CONTENTS:

 User Manual (this document)

 MC-11+ Rewinder Unit

 Adjustable Core Holder

 Power Supply Module

Retain the Shipping Container and Packaging for Storage and Transport

SPECIFICATIONS:

Weight of the machine: 5,6Kg

Max. Label Roll Weight: 3Kg.

Max. Label Roll Diam.: mm. 220

Start/Stop: ON/OFF/ON Direction Switch

Power Supply: Input: 220-240VAC -60Hz. –50

Output: 15VDC 800mA.–

WARNING!

This Product is for indoor

use only.

Not for use in wet locations.

IMPORTANT INFORMATION:

 This product is a label rewinder It is only to be used to rewind labels of the

recommended dimensions and weight in an indoor, dry environment.

 The machine has to be unplugged before any manipulation.

 The machine is to be used on a ﬂat surface, if the surface is not ﬂat, it is to be ﬁxed

using the holes in the base plate.

 Do not leave the power cable in a passageway.

 The ambient light of the working area needs to be suﬃcient to avoid any risk.

 The rewinder can be used in ambient temperatures of +2°C to 40°C.

 Connection of the machine to the power source must respect local and European

legislations.

SET-UP:

1. Place the - so that the three (3) Rewind Fingers are perpendicular to the web MC 11+

of the labels to be rewound. The - is bi-directional, and can be operated in MC 11+

either direction.

2. Verify that the (ON-OFF-ON) Direction Switch on the rear of the - is in the MC 11+

OFF (0) position.

3. Insert the Power Supply Cord into the Power Jack on the rear of the - . MC 11+

4. Plug the AC/DC Adapter into a suitable electrical outlet. The AC/DC Adapter can be

left plugged in at all times.

5. The Rewinder has a combination Power and (ON-OFF- rection Switch on the ON) Di

rear panel. See the photo below. To make the Rewinder run to the right (looking from

the rear of the Rewinder), press the Power/Direction Switch in the direction of the

right arrow. To make the Rewinder run to the left, press the Power / Direction Switch

in the direction of the left arrow.

FOR YOUR SAFETY:

Switch oﬀ device before any manipulation

REWINDING LABELS:

Rewind labels onto any core 25-101mm diameter. The Adjustable Core Holder is

supplied fully assembled. Please, refer to the ACH Manual User enclosed to set it up.

1. Pull the label web to the cardboard core and use a piece of tape to secure the label

web.

2. Adjust the position of the - if necessary so it is square with the label path. MC 11+

3. If you are using the APG-MC Adjustable Paper Guide, move the Arm into position to

guide the outer edge of the labels and lock it into place.

4. Place the - (ON-OFF-ON) rection Switch to the ON position in the desired MC 11+ Di

direction of operation, left or right.

5. Start the printer and adjust the "SPEED/TORQUE" Control Knob for the

desired take-up tension. Use the minimum "SPEED/TORQUE" setting

needed to rewind labels properly. Excessive torque might pull the labels

too hard and cause the printer to lose registration.

6. When ﬁnished, place the (ON-OFF-ON) Direction Switch to the OFF (0) position.

7. If the APG-MC Adjustable Paper Guide is in use, unlock and move the Arm out of the

way.

8. Slide the cardboard core and the wound labels oﬀ the -11+. You do not need to MC

loosen the three (3) Locking Levers unless you want to use a diﬀerent diameter core.

EXTERNAL CONTROL

The MC+ can be controlled by the printer. A 3.5mm (mono) connector for an External

Control Input (start/stop) is provided and a matching jack is enclosed. The MC+ can react

to diﬀerent types of signals provided by the printer. The selection of the signal nature is

done via 2 jumpers on the MC+ internal PCB. Four modes are selectable: Open Collector

High Active, Open Collector Low Active, Logic Level High Active ( ) & Logic Max 10VDC

Level Low Active (Max 10VDC . )

The factory setting is “Open Collector high”. Other default setting on request.

JP2

JP3

SIG ACT LOW

SIG ACT HIGH

OPEN COL LOW

OPEN COL HIGH

Product specificaties

Merk:	Labelmate
Categorie:	Labelprinter
Model:	MC-11+
Kleur van het product:	Zwart
Ingebouwd display:	Nee
Netbelasting:	- W
Soort:	Handmatige etiketteermachine
Container diameter (max):	101 mm
Label snelheid:	500 mm/sec
Container diameter (min):	25 mm
Container breedte (max):	115 mm