La Crosse Technology 308-2408FR Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor La Crosse Technology 308-2408FR (6 pagina's) in de categorie Weerstation. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6
Model: 308-2408FR www.lacrosseclock.com/support Page | 1
Model: 308 2408FR-
Instruction Manual
DC: 103015
LED ALARM CLOCK WITH IN/OUT TEMPERATURE
Note: This product
displays temperature in
Fahrenheit only.
Model: 308-2408FR www.lacrosseclock.com/support Page | 2
WWVB Atomic Time Signal Search
After your clock is powered up, it searches for the Atomic time signal for
seven minutes icon flashes. . The
Note: During Atomic time signal search the buttons will not function, . The
LED will change to low brightness and will return to high brightness after
the Atomic time search . search
Receiving Atomic signal ( icon flashing)
Successful Reception ( icon becomes static)
s Failed Reception ( icon disappear )
H es old / WAVE button until your clock giv a short beep to stop or start
the Atomic time . signal reception
During the search, press button once to show reception mode / WAVE
and signal strength Indication:-
When a strong signal is detected, display shows with 3 bars
During reception, the signal strength may move from 1 bar to 2 bars
to 3 bars. This is normal since the clock is detecting Atomic time
signal and other signals in the air at the same time.
Press SET will return to the time display with icon flashing.
For information about WWVB Atomic time visit:
www.nist.gov/pml/div688/grp40/wwvb.cfm
G et Started
Step 1: Insert the AC/DC adaptor to a into the back n outlet hen , t
of the clock.
Step 2 I(Optional): nsert 1 x CR2032 Lithium battery (not
included) to the battery compartment on the back of the
clock . The + side of the battery should face up.
T W004
Sensor
Reset
Stand
Battery
Compartment
2 AAA batteries
LED
Model: 308-2408FR www.lacrosseclock.com/support Page | 3
Step 3: Slide open the battery cover of the wireless TW004
sensor, make sure the channel selector is set at position 1
(top position). Insert 2 x AAA batteries (not included) into
the outdoor sensor. Observe the correct polarity.
Step 4: Peel off the protective label on the front of the clock.
Restart: If the outdoor temperature is not displayed after 3
minutes, remove AC power and & outdoor batteries from the clock
sensor. Press any button on the clock 20 times. After 5 minutes,
return to Step 1 above.
Manual Set Time
1. the button Hold SET to enter time set mode.
2. Press the ▼ or ▲ buttons to adjust the values.
3. the button Press TSE to confirm adjustments and move to the next
item.
Time setting order:
1. Time Zone time zones (- 4 04 Default)
2. DST (Daylight Saving Time On/Off)
3. Hour
4. Minutes
5. Snooze Time (05 -60 minutes)
Press the button SET to exit, or 0 seconds without pressing wait 1
buttons to return to the normal time display.
Set Time Alarm
1. the Hold AL ON.OFF button to enter alarm set mode.
2. values. Press the ▼ or ▲ buttons to adjust the
3. the Press AL ON.OFF button to confirm
adjustments.
Time setting order: 1. Hour 2. Minutes
Press the AL ON.OFF button to exit, or wait 8
seconds without pressing buttons to return to the normal time display.
Note: The alarm will sound for two minutes, then shut off completely.
Activate/Deactivate time Alarm
Press the AL ON.OFF button once to activate the alarm.
The letters AL will appear above the time when the alarm is active.
Press the AL ON.OFF button once again to deactivate the alarm.
TIME ZONES:
04 Pacific
03 Mountain
02 Central
01 Eastern


Product specificaties

Merk: La Crosse Technology
Categorie: Weerstation
Model: 308-2408FR

Heb je hulp nodig?

Als je hulp nodig hebt met La Crosse Technology 308-2408FR stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Weerstation La Crosse Technology

Handleiding Weerstation

Nieuwste handleidingen voor Weerstation