Kyoritsu KEW2007R Handleiding

Kyoritsu Multimeter KEW2007R

Lees hieronder de 📖 handleiding in het Nederlandse voor Kyoritsu KEW2007R (2 pagina's) in de categorie Multimeter. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

INSTRUCTION MANUAL

DIGITAL CLAMP METER

KEW2007R

1. Safety Warnings

This instrument has been designed, manufactured and

tested according to IEC 61010: Safety requirements for

Electronic measuring apparatus, and delivered in the best

condition after passed the inspection. This instruction

manual contains warnings and safety rules which must be

observed by the user to ensure safe operation of the

instrument and retain it in safe condition. Therefore, read

through these operating instructions before using the

instrument.

WARNING

● Read through and understand the instructions contained

in this manual before using the instrument.

● Keep the manual at hand to enable quick reference

whenever necessary.

● The instrument is to be used only in its intended

applications.

● Understand and follow all the safety instructions

contained in the manual.

● It is essential that the above instructions are adhered to.

Failure to follow the above instructions may impair the

protection provided by the instrument and test leads, and

may cause injury, instrument damage and/or damage to

equipment under test.

The symbol indicated on the instrument means that the

user must refer to the related parts in the manual for safe

operation of the instrument. It is essential to read the

instructions wherever the symbol appears in the manual.

DANGER is reserved for conditions and actions that

are likely to cause serious or fatal injury.

WARNING is reserved for conditions and actions that

can cause serious or fatal injury.

CAUTION is reserved for conditions and actions that

can cause injury or instrument damage.

● Marks listed below are used on this instrument.

User must refer to the manual.

Instrument with double or reinforced insulation

Indicates that this instrument can clamp on

bare conductors when measuring a voltage

corresponding to the applicable measurement

category, which is marked next to this symbol.

AC DC Ground (Earth)

This instrument is subject to WEEE Directive

(2002/96/EC). Please contact our dealer near

you at disposal.

Measurement Category

OCircuits which are not directly connected to the mains

power supply.

CAT II Primary electrical circuits of equipment connected

to an AC electrical outlet by a power cord.

CAT III Primary electrical circuits of the equipment

connected directly to the distribution panel, and feeders

from the distribution panel to outlets.

CAT IV The circuit from the service drop to the service

entrance, and to the power meter and primary over current

protection device(distribution panel).

This instrument is designed for CAT IV 300V / CAT III

600V. Test leads M-7066A with the supplied cap are

designed for CAT IV 600V / CAT III 1000V and without

the caps are for CAT II 1000V.

DANGER

● Never make measurements under the circumstances

exceed the designed measurement category and the

rated voltage of the instrument and the test leads.

● Do not attempt to make measurement in the presence of

flammable gasses. Otherwise, the use of the instrument

may cause sparking, which can lead to an explosion.

● Never attempt to use the instrument if its surface or your

hand is wet.

● Do not exceed the maximum allowable input of any

measuring range.

● Never open the Battery cover during a measurement.

● To avoid electrical shock by touching the equipment

under test or its surroundings, be sure to wear insulated

protective gear.

● Never measure current while the test leads are inserted

into the input terminals.

● Test leads to be used for voltage measurements shall be

rated as appropriate for Measurement Category III or IV

according to IEC 61010-031 and shall have a voltage

rating of 600V or higher.

● Barriers on the instrument body and the test leads

provide protection to keep your fingers and hands from

touching an object under test. Keep your fingers and

hands behind the barriers during measurement.

WARNING

● Never attempt to make measurement if any abnormal

conditions, such as broken case and exposed metal

parts are found on the instrument or test leads.

● Verify proper operation on a known source before use or

take action as a result of the indication of the instrument.

● Firmly attach the caps to the test leads when

performing measurements in CAT III or higher test

environments. When KEW2007R and the test leads

are combined and used together, whichever is lower

category & voltage to earth either of them belong to

is applied.

● Do not rotate the Function Switch if the instrument and

the equipment under test are connected.

● Do not install substitute parts or make any modification to

the instrument. For repair or re-calibration, return the

instrument to your local KYORITSU distributor

CAUTION

● Use of this instrument is limited to domestic, commercial

and light industry applications. Strong electromagnetic

interference or strong magnetic fields, generated by

large currents, may cause malfunction of the instrument.

● Connect the test leads to the terminals firmly.

● This instrument isn’t water proofed. Keep away from

water.

● Do not pull or twist the test leads to prevent the risk of

damage.

● Power off the instrument after use. Remove batteries if

the instrument is to be stored and will not be in use for a

long period.

● Do not expose the instrument to the direct sunlight, high

temperature and humidity or dewfall.

● Use a cloth dipped in water or neutral detergent for

cleaning the instrument. Do not use abrasives or solvents.

NOTE

● The LCD shows some digits at the ACV and the DCV

ranges even while the test leads are open. In addition,

the LCD shows some digits instead of 0 when short-

circuiting the test leads. However, these phenomena

don’t affect measurement results.

2. Specification

Temperature: 23 ± 5°C, Humidity: 45 - 75%

ACA (Auto-range)

Range Display Range Accuracy (sine wave)*1

600A 0.0, 0.4-629.9A ±1.5 %rdg±4dgt (45-65Hz)

±2.0 %rdg±4dgt (40-400Hz)

1000A 570-1049A

*1 : when the measured conductor is in the center of clamp jaw

Guaranteed accuracy : 0.8A -1000A,less than 1500A Peak

Input protective current : AC1200A

ACV

Range Display Range Accuracy (sine wave)

600V 0.0, 0.6-629.9V ±1.2 %rdg±3dgt (45-65Hz)

±1.5 %rdg±4dgt (40-400Hz)

Guaranteed accuracy : 1.0V - 600.0V,less than 900V Peak

Input protective voltage : AC/DC720V 10 sec

DCV

Range Display Range Accuracy

600V 0.0-±629.9V ±1.2%rdg±3dgt

Guaranteed accuracy : 0.0V - ± 600.0V

Input protective voltage : AC/DC720V 10 sec

ACV/DCV input impedance : approx. 10MΩ

Resistance / Continuity (Auto-range)

Range Display Range Accuracy

600Ω 0.0-629.9 Ω ±1.3%rdg±5dgt

6kΩ 0.570-6.299 kΩ ±2.0%rdg±3dgt

Cont. 0.0-629.9 Ω Bz threshold value <90Ω

Guaranteed accuracy : 0.0Ω - 6.000kΩ

Open-loop voltage : 3V or less

Input protective voltage : AC/DC600V 10 sec

●Measuring method : ⊿Σ modulation

●Over-range indication : OL

●Measurement cycle : 2.5 times per second

●Crest factor : less than 3 (45-65Hz)

Add ±0.5%rdg±5dgt to above specified accuracies.

(Applicable functions : ACA, ACV)

●Applicable Standards :

IEC 61010-1/ 61010-2-032/ 61010-2-033 (instrument)

Pollution degree 2, Indoor use, Altitude up to 2000m

CAT III 600V / CAT IV 300V

IEC 61010-031(Test leads Model 7066A)

w/ caps CAT IV 600V / CAT III 1000V

w/o caps CAT II 1000V

IEC61326 (EMC), EN50581 (RoHS)

●Withstand voltage : AC5160Vrms 5sec

between current sensor and enclosure or

circuit and enclosure

●IP rating : IP40 (IEC60529)

●Insulation resistance :

>100MΩ /1000V between enclosure and electrical circuit

Function

Switch

Current Sensor

Hold Key

LCD

V/Ω

Terminal

COM

Terminal

Trigger

Cap

Barrier of Test Leads

Barrier

Wrist Strap

Screw

●Operating Temperature and humidity range :

0 to 40°C 85%RH or less (no condensation)

●Storage Temperature and humidity range :

-20 to 60°C 85%RH or less (no condensation)

●Power source : DC3V R03 / LR03 (AAA) ×2

●Current consumption : < 4mA

●Battery life (ACA, continuous, no load, with R03) :

approx. 170 hours

●Dimension, Weight : 204(L)×81(W)×36(D)mm,

approx. 220g (including batteries)

●Accessories :

Test leads Model 7066A 1set

Battery R03(AAA) 2pcs

Instruction manual 1pce

Carrying case Model 9079 1pce

3. ACA Measurement

DANGER

●Disconnect the test leads from the instrument when

performing a test.

●Do not exceed the rated voltage (600V) and the

category ratings of the instrument.

●Keep your fingers and hands behind the barrier

during measurement.

(1) Set the Function switch to ACA position.

(2) Press the trigger to open the Current Sensor and clamp

the one conductor (Dia. 33mm max.) under test.

NOTE

Measurement accuracy is guaranteed when the measured

object is placed at the center of the Current Sensor.

4. ACV/DCV Measurement

DANGER

●Before starting a measurement, ensure that the

Function switch is set to the appropriate position.

●Do not exceed the rated voltage (600V) and the

category ratings of the instrument.

●Keep your fingers and hands behind the barrier

during measurement.

(1) Set the Function switch to ACV or DCV position.

(2) Firmly connect the test leads to V/Ω and COM terminals.

NOTE

If the connection is reversed, the LCD indicates the

“ “ mark (DCV measurement).－

5.Resistance(Continuity)Measurement

WARNING

Power off the circuit under test before making

measurements with this instrument.

(1) Set the Function switch to resistance or continuity

position.

(2) Firmly connect the test leads to V/Ω and COM terminals.

Beeps less than 90Ω.

NOTE

LCD indicates ”OL” when the test leads are open.

6. Other Functions

●Data Hold

Press the Hold key. The LCD shows “ ” mark and the

reading will be held.

Press the Data Hold Key again

to release the display.

●Low battery indication

The LCD shows “ ” mark when the batteries fall

below the normal operating voltage.

●Sleep Function

Automatically powers off the instrument in about 10 min

after the last switch or key operation. Buzzer beeps five

times one minute before entering into the Sleep mode,

and also one time just before entering into the mode. To

exit from the Sleep mode, rotate the Function switch or

press Hold key.

To disable the Sleep function,

press the HOLD key and

power on the instrument.

Confirm that the LCD shows

“ ” about 1 sec.

7. Battery Replacement

WARNING

● Replace the batteries when a Low Battery Voltage

warning " " mark is indicated on the LCD. Otherwise,

precise measurement cannot be made.

If batteries are completely exhausted, the LCD goes

blank without showing " " mark.

● Do not try to replace the batteries if the surface of the

instrument is wet.

● Disconnect the test leads from the object under test and

power off the instrument before opening the Battery

Compartment Cover for battery replacement.

CAUTION

● Do not mix old and new batteries. Brand and type of the

batteries to be used should be harmonized.

● Install batteries in correct polarity as indicated in

the Battery Compartment.

(1) Set the Function Switch to "OFF" position.

(2) Unscrew and remove the Battery Compartment Cover

on the instrument.

(3) Replace the batteries observing correct polarity.

Use new two AAA 1.5V batteries.

(4) Install the Battery Compartment Cover and tighten the

screw.

MEMO

11-15 92-2261

DISTRIBUTOR

Kyoritsu reserves the rights to change specifications

or designs described in this manual without notice

and without obligations.

ACV DCV

Black(-) Red(+)

Resistance

Con

tinuity

Correct Incorrect

♪

Replace the batteries

with new ones when

this mark appears.

Product specificaties

Merk:	Kyoritsu
Categorie:	Multimeter
Model:	KEW2007R

Heb je hulp nodig?

Als je hulp nodig hebt met Kyoritsu KEW2007R stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Multimeter Kyoritsu

Kyoritsu KEW 2510 Handleiding

5 Januari 2024

Kyoritsu KEW 2500 Handleiding

5 Januari 2024

Kyoritsu KEW 2413R Handleiding

5 Januari 2024

Kyoritsu KT 200 Handleiding

5 Januari 2024

Kyoritsu 2431 Handleiding

5 Januari 2024

Kyoritsu 2434 Handleiding

4 Januari 2024

Kyoritsu KEW Snap 2433 Handleiding

4 Januari 2024

Kyoritsu KEW 2300R Handleiding

19 December 2023

Kyoritsu KEW 1052 Handleiding

23 Mei 2023

Kyoritsu KEW2200 Handleiding

6 Mei 2023

Handleiding Multimeter

Nieuwste handleidingen voor Multimeter

Megger DPM1000 Handleiding

17 November 2024

Testec TT-CC 220 Handleiding

14 November 2024

Testboy Pen 1000 Handleiding

11 November 2024

PCE Instruments PCE-123 Handleiding

22 Oktober 2024

PCE Instruments PCE-IT 200 Handleiding

16 Oktober 2024

PCE Instruments PCE-ITM 20 Handleiding

16 Oktober 2024

PCE Instruments PCE-LT 15 Handleiding

16 Oktober 2024

PCE Instruments PCE-PHM 14 Handleiding

16 Oktober 2024

PCE Instruments PCE-228 Handleiding

16 Oktober 2024

Voltcraft PMM 3005-20 Handleiding

30 September 2024