Kramer VS-44H2A Handleiding

Kramer Schakelaar VS-44H2A

Lees hieronder de 📖 handleiding in het Nederlandse voor Kramer VS-44H2A (4 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

VS-44H2A Quick Start

P/N:

2900- 301078QS

Rev:

Scan for full manual

VS- 44H2A Quick Start Guide

This guide helps you install and use your VS-44H2A for the first time.

Go to www.kramerav.com/downloads/VS-44H2A to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check what’s b in the ox

VS-44H2A 4K HDMI 4x4 Matrix Switcher

1 Set of rack ears

4 Rubber feet

Remote control transmitter with batteries

1 Power cord

1 Quick start guide

Step 2: Get to know your VS- 44H2A

# Feature Function

IR Sensor

Receives signals from the infrared remote-control transmitter.

IR LED

Lights yellow when receiving an IR signal.

2 ALL Button Press followed by an input button to connect the selected input to all outputs .

For example, press ALL and then Input button # 2 to connect input # 2 to all the outputs.

OFF Button

Press after pressing an output button to disconnect the selected output from the inputs.

To disconnect all the outputs, press ALL followed by OFF.

4 IN Select Buttons (1 to 4) Press to select the input to switch after selecting an output (also used for storing machine

setups).

OUT Select Buttons (1 to 4)

Press to select an output to switch followed by an input.

STO Button

Press STO followed by an INPUT (1 to 4) button to store the current switching

configuration to the location corresponding to that INPUT number.

7 RCL Button Press RCL followed by the corresponding INPUT (1 to 4) button to recall the preset

switching configuration saved in that location.

LOCK Button

Press and hold to toggle the locking/release of the front panel buttons.

EDID Button

Press EDID + STO buttons to enter EDID mode.the

OUTPUT/INPUT 7-segment LED

Display

Displays the input currently switched to the output which is marked above each input.

# Feature Function

HDMI™ IN Connectors (1 to 4)

Connect to up to 4 HDMI sources.

S/PDIF OUT (coaxial) RCA

Connectors (1 to 4)

Connect to up to 4 digital audio acceptors.

HDMI OUT Connectors (1 to 4)

Connect to up to 4 HDMI acceptors.

14 BALANCED AUDIO OUT Terminal

Block Connectors (1 to 4)

Connect to up to 4 balanced stereo audio acceptors.

PROG USB Connector

Connect to a USB stick to perform firmware upgrades.

ETHERNET RJ- 45 Connector

Connect to a PC via a LAN.

RS- -232 9 pin D-sub Connector

Connect to a PC/serial controller.

IR IN 3.5mm Mini Jack Connector

Connect to an external IR receiver for controlling the device via IR remote controller

Covered by a cap. The 3.5mm jack at the end of the internal IR connection cable fits into

this opening.

Mains Power Connector and Fuse

Plug in the power cord.

Power Illuminated Switch

Turn the device on and off.

Step 3: VS-Install the 44H2A

To rack mount the machine attach both ear brackets (by removing the three screws from each side of ,

the machine and replacing those screws through the ear brackets) or place the machine on a table.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your VS-44H2A. For best results, we recommend that

you always use Kramer high performance cables to connect AV equipment to the - VS-44H2A.

Connect the audio output

To a balanced

stereo audio

acceptor:

To an unbalanced

stereo audio

acceptor:

Step 5: Connect the power

Connect the power cord to VS-44H2A and plug it into the mains electricity.

Safety Instructions

Caution:

There are no operator serviceable parts inside the unit.

Warning:

Use only the power cord that is supplied with the unit.

Warning:

Do not open the unit. High voltages can cause electrical shock! Servicing by

qualified personnel only.

Warning:

Disconnect the power and unplug the unit from the wall before installing.

See www.KramerAV.com for updated safety information

Step 6: Operate the - VS 44H2A

Operate via: RS-232 and Ethernet communication parameters :

Operate Product via:

• Front panel buttons

• Remotely, by RS-232 serial

commands transmitted by a

touch screen system, PC, or

other serial controller

• Remotely, using the IR

remote control transmitter

• Embedded web pages via

the Ethernet

RS- 232/Ethernet

Baud Rate:

115,200

Parity:

None

Data Bits:

Command Format:

ASCII Protocol 3000

Stop Bits:

Example (Route input 1 to output 1):

#VID 1>1<cr>

Ethernet Parameters

IP Address:

192.168.1.39

Default TCP Port #:

5000

Subnet Mask:

255.255.0.0

Default UDP Port #:

50000

Default Gateway:

192.168.0.1

Full Factory Reset

Front panel:

There is no option for factory reset from front panel.

Protocol 3000:

“#factory” command.

Web Pages:

Device Settings page, Soft Factory Reset resets all

parameters to factory default except for network parameters.

Switch an input to an output via front panel buttons

Press an output button followed by an input button to switch the selected input to the selected output.

Store a switching setting

1. Configure the switching as required for the preset.

2. Press STO. The STO button flashes.

3. - Select an input button (1 4).

4. Press STO to store the current setup. The STO button stops

flashing.

Recall a switching setting

1. Press RCL. The RCL button flashes.

2. Press the relevant input button that stored the preset.

3. Press RCL to recall the stored preset. The RCL button stops

flashing.

Acquiring the EDID

Acquire EDID from:

• One output to one or more of the inputs.

• Different outputs to different inputs.

• The default EDID reading EDID from an output that is not connected to an acceptor) (by .

To acquire an EDID from an output to an input connect the output to an acceptor, and then:

1. Press and hold EDID and STO for 3 seconds. Both buttons flash.

2. Press an input button (to which the EDID is copied) selected button flashes.

3. Press an output button (from which the EDID is acquired).

4. Press W EDID. ait until the device acquires the EDID and EDID and STO stop flashing.

To acquire an EDID from different outputs to different inputs, connect the outputs to acceptors and then:

1. Press and hold EDID and STO for 3 seconds. Both buttons flash.

2. Press an input button (to which the EDID is copied) selected button flashes.

3. Press an output button (from which the EDID is acquired).

4. Press the selected input button again. The button stops flashing.

5. repeat steps 2 to 3.

6. Press EDID. Wait until the device acquires the EDID and EDID and STO stop flashing.

Product specificaties

Merk:	Kramer
Categorie:	Schakelaar
Model:	VS-44H2A
Ingebouwd display:	Nee
Gewicht:	2000 g
Breedte:	436.4 mm
Diepte:	237.2 mm
Hoogte:	43.6 mm
Gewicht verpakking:	2900 g
Breedte verpakking:	525 mm
Diepte verpakking:	330 mm
Hoogte verpakking:	107 mm
Materiaal behuizing:	Aluminium
Aan/uitschakelaar:	Ja
USB-connectortype:	Mini-USB
Kleur behuizing:	Zwart
Aantal Ethernet LAN (RJ-45)-poorten:	1
Aantal USB-aansluitingen:	1
Certificering:	CE, WEEE
HDCP:	Ja
RS-232 port:	1
HDMI versie:	2.0
Aantal HDMI-invoerpoorten:	4
Remote (IR) ingang:	1
Duurzaamheidscertificaten:	RoHS
Temperatuur bij opslag:	-40 - 70 °C
Rack-montage:	Ja
HDCP versie:	2.2
Aantal HDMI-uitvoerpoorten:	4
Rackcapaciteit:	1U
AC-ingangsspanning:	100-240 V
AC-ingangsfrequentie:	50 - 60 Hz
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Type product:	AV-matrixschakelaar
Code geharmoniseerd systeem (HS):	85299097