Konig CMP-PSUTESTER5 Handleiding

Konig Niet gecategoriseerd CMP-PSUTESTER5

Lees hieronder de 📖 handleiding in het Nederlandse voor Konig CMP-PSUTESTER5 (30 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 204 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/30

ČeskySvenskaSuomiMagyar

Español

ItalianoNederlandsFrançaisDeutschEnglish

CMP-PSUTESTER5

Power supply tester

MANUAL

MODE D’EMPLOI

MANUALE

HASZNÁLATI ÚTMUTATÓ

BRUKSANVISNING

ANLEITUNG

GEBRUIKSAANWIJZING

MANUAL DE USO

KÄYTTÖOHJE

NÁVOD K POUŽITÍ

Česky Svenska Suomi Magyar Español Italiano Français Deutsch English

Nederlands

A must have tool for anyone with PCs to test power supplies before putting them into

a PC. A bad power supply could damage system components if the voltages are not

correct, and do not assume that a brand new supply will always operate correctly.

Instructions:

BE AWARE: NEVER PLUG IN 2 CONNECTORS AT THE SAME TIME (NOT INCLUDING

THE 24/20 PIN CONNECTOR)

1. Plug in your 24/20 pin power supply connector to the tester.

2. Turn on your power supply.

3. LCD shows each voltage and P.G. value on the screen automatically and two beeps

can be heard.

4. The ATX power output connectors will be checked one by one. If the power output is

working properly the LED will come on, when it’s not working properly the LED light

will not come on.

5. Plug in the HDD and afterwards the Floppy connector and check the LED light

(+12V1 and +5V).

6. Plug in the SATA connector and check the LED light (+12V1, +5V and +3.3V).

7. Remove the connectors after checking (accept 24/20 PIN).

8. When abnormal voltage is detected it will not be displayed on the screen.

9. When no voltage is detected the screen will show “LL”.

10. When a voltage below minimum is detected it will show “LL”.

11. When a voltage higher than maximum is detected it will show “HH”.

12. When a voltage is detected which is lower or higher than the value shown in the

table below an alarm will sound.

13. When a P.G. value is detected which is lower than 100ms or higher than 900ms an

alarm will sound.

14. With any abnormality an alarm will sound and the related digit will blink.

ČeskySvenskaSuomiMagyar

Español

ItalianoNederlandsFrançaisDeutschEnglish

Normal Voltage range Display Voltage range

Lower (A) Higher (B) Min. ( C) Max. (D)

+5V 5V +4.75V +5.25V 4V 6.0V

-12V -12V -11V -13V -10V -14V

+12V1 12V 11V +13V 10V 14V

+12V2 12V 11V +13V 10V 14V

+3.3V 3.3V +3.14V +3.47V 2.0V 4.5V

+5VSB 5V +4.75V +5.25V 4.0V 6.0V

PG 0ms 990ms

Warning: This product is designed only for power supply output tests. Do not leave the

tester connected to the power supply unattended. It generates heat and could possibly

damage your power supply.

All brands and registered trademarks are property of the respective possessors.

Safety precautions:

To reduce risk of electric shock, this product should ONLY be opened by an authorized

technician when service is required. Disconnect the product from mains and other

equipment if a problem should occur. Do not expose the product to water or moisture.

Warranty:

No guarantee or liability can be accepted for any changes and modiﬁ cations of the

product or damage caused due to incorrect use of this product.

General:

Designs and speciﬁ cations are subject to change without notice.

All logos brands and product names are trademarks or registered trademarks of their

respective holders and are hereby recognized as such.

Attention:

This product is marked with this symbol. It means that used electrical and

electronic products should not be mixed with general household waste. There

is a separate collections system for these products.

Product specificaties

Merk:	Konig
Categorie:	Niet gecategoriseerd
Model:	CMP-PSUTESTER5
Kleur van het product:	Zwart
Ingebouwd display:	Ja
Gewicht verpakking:	140 g
Breedte verpakking:	120 mm
Diepte verpakking:	25 mm
Hoogte verpakking:	150 mm
LED-indicatoren:	Ja
Backlight-kleur:	Blauw
Type beeldscherm:	LCD
Display met achtergrondverlichting:	Ja
DC uitgangsspanningtest:	+12V, +3.3V, +5V
Ondersteunde voedingsconnectors:	ATX (20-pin), ATX (24-pin), CPU (8-pin), CPU P4 (4-pin), Floppy drive, PCI Express (6-pin), Peripheral (Molex) (4-pin), SATA