Konig CMP-BARSCAN30 Handleiding

Konig Barcode lezer CMP-BARSCAN30

Lees hieronder de 📖 handleiding in het Nederlandse voor Konig CMP-BARSCAN30 (48 pagina's) in de categorie Barcode lezer . Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/48

CONTENTS

Getting Started ----------------------------------------------------------

Setup Procedures --------------------------------------------------------

Setup Menu---------------------------------------------------------------

Setup flow Chart --------------------------------------------------------

Group 0 : Interface Selection ----------------------------------------

Group 1 : Device Selection for keyboard interface---------------

6-7

Group 2 : Inter-character Delay -------------------------------------

Group 3 : Language for Keyboard Interface ----------------------

9-10

Group 4 : Terminator--------------------------------------------------

11-12

Group 5 : Scan Mode -------------------------------------------------

13-14

Group 6 : Preamble and Postamble ---------------------------------

Group 7 : Reserved ---------------------------------------------------

Group 8 : RS-232 Parameters ---------------------------------------

16-18

Group 9 : Code 39 / Code 32 ----------------------------------------

19-20

Group 10-1: Interleaved 2 of 5 ---------------------------------------

Group 10-2: Industrial 2 of 5 / IATA---------------------------------

Group 10-3: Matrix 2 of 5----------------------------------------------

Group 10-4: China Postage--------------------------------------------

Group 11 : Code 128/ Code 93/ Code 11/ MSI-PLESSEY------

25-26

Group 12 : ISBN/ISSN-------------------------------------------------

Group 13 : Codabar / NW7--------------------------------------------

Group 14 : Code 4------------------------------------------------------

Group 15-1 : EAN 13 / JAN 13---------------------------------------

Group 15-2 : UPC-A----------------------------------------------------

Group 15-3 : EAN-8 / JAN-8------------------------------------------

Group 15-4 : UPC-E / UCC EAN-128-------------------------------

Group 16 : General Parameters---------------------------------------

Group 17 : Code ID Settings------------------------------------------

Group 18 : Wand Type Parameters----------------------------------

Group 19 : Magnetic Parameters-------------------------------------

37-39

Group 20 : Function Key Emulation---------------------------------

Function Code for PC XT/AT

41-42

Table-Hex : Hexadecimal---

ASCII Table---------------

Hexadecimal-Decimal Conver

Pin Assignments of Scanner

46-47

Getting Started

Installing Keyboard Wedge Scanner

To install a keyboard wedge scanner, follow the steps listed below:

1) Make sure that the scanner has the correct Y (U)- cable for the system (a PC or terminal)

2) Turn off the power of the system

3) Unplug the keyboard from the system

4) Connect the Y (U)- cable to the system and keyboard

5) Turn on the power of the system

6) If the indicator LED lights up and the buzzer sounds, the scanner is ready for reading

Installing a RS-232 Interface Scanner

To install a RS-232 interface scanner, the host device should have a RS-232 port to

receive data from the scanner, follow the steps listed below:

1) Make sure that the scanner has the right connector for the RS-232 port of the host device

2) Make sure that there is a power supply to the scanner (if necessary)

3) Connect the cable to the RS-232 port of the device

4) If the indicator LED lights up and the buzzer sounds, the scanner is ready for reading

Setup Procedures

1) Locate a group that contains the parameters to be changed.

2) Scan the “Enter Group #” label. The scanner will sound beeps indicate that setup is in progress

3) Scan the label representing the parameter to be changed

4) Scan the “Exit” to end the group currently selected, the scanner will sound beeps.

5) Repeat the procedure for other groups including the parameters to be changed

Example 1:

Set the operating mode to “Continuous mode”

1) Scan “Enter Group 5”

2) Scan “Continuous/Trigger off”

3) Scan “Exit”

Example 2

Assign Preamble string as “#”, and postamble string as “END”

1) Scan “Enter Group 6”

2) Scan Preamble”

3) Scan “#” from “Full ASCII Table and Table-Hex.”

4) Scan “Confirm” Label in Table-Hex

5) Scan “Postamble”

6) Scan “E”, “N”, “D” from “Full ASCII Table and Table Hex” consecutively

7) Scan “Confirm” Label in Table-Hex.

8) Scan Exit

Product specificaties

Merk:	Konig
Categorie:	Barcode lezer
Model:	CMP-BARSCAN30
Kleur van het product:	Grijs
Gewicht:	160 g
Materiaal behuizing:	ABS kunststof
Schokbestendig:	Ja
Certificering:	FCC class A
Type beeldsensor:	Laser
Type processor:	Intel 80C31
Temperatuur bij opslag:	-20 - 65 °C
Golflengte:	670 nm
Stroomverbruik:	90 mA
Standaard interfaces:	USB
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Licht niveaus (direct zonlicht):	3000 - 8000 Lux
Scansnelheid:	100 sec/pagina