Klipsch SLX Handleiding

Klipsch Speaker SLX

Lees hieronder de 📖 handleiding in het Nederlandse voor Klipsch SLX (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

SYNERGY SERIES

IMPORTANT SAFETY INSTRUCTIONS

1. READ these instructions.

2. KEEP these instructions.

3. HEED all warnings.

4. FOLLOW all instructions.

5. DO NOT use this apparatus near water.

6. CLEAN ONLY with dry cloth.

7. DO NOT block any ventilation openings. Install in accordance with the manufacturer's

instructions.

8. DO NOT install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including ampliﬁers) that produce heat.

9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug

has two blades with one wider than the other. A grounding type plug has two blades and a

third grounding prong. The wider blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult an electrician for replacement of the

obsolete outlet.

10. PROTECT the power cord from being walked on or pinched, particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. ONLY USE attachments/accessories speciﬁed by the manufacturer.

12. tripod, bracket, or table speciﬁed by the manufacturer, or soldUSE only with a cart, stand,

with the apparatus. When a cart is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13. UNPLUG this a tus during lightning storms or when unused for long periods of time.ppara

14. REFER all servicing to qualiﬁed service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has

been spilled or objects have fallen into the a tus, tus has been exposed toppara the appara

rain or moisture, does not operate normally, or has been dropped.

This symbol indicates that there are important operating and maintenance instructions

in the litera ying this unit.ture accompan

This symbol indicates that dangerous voltage constituting a risk of electric shock is

present within this unit.

WARNING: To reduce the risk of ﬁre or electrical shock, do not expose this apparatus to rain

or moisture.

WARNING: Voltages in this equipment are hazardous to life. No user-serviceable parts inside.

Refer all servicing to qualified service personnel.

CAUTION: Changes or modiﬁcations not expressly approved by the manufacturer could void the

user’s authority to operate this device.

ABOUT YOUR KLIPSCH PURCHASE

Thank you for your purchase of Klipsch speakers.After reading this manual and connecting your

system, you will hear the result of over 55 years of stringent engineering and class-leading

research and development. Like all Klipsch products, your speakers feature Klipsch Horn-loaded

Technology—the guiding design for the first Klipschorn®developed in 1946 and for every

product tha t has followed. Horn-loading allows your speakers to deliver high sensitivity, low

distortion,f lat frequency response and wide dispersion, which translates to unequaled power,

detail and dynamics, the hallmarks of “The Klipsch Sound.” Please be sure to fill out the

included Warranty card or register online at www.klipsch.com so we are better able to serve

you. Again, thank you for choosing Klipsch and we hope that your speakers bring life to your

music and movies for many years.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

GRILLE

The speaker can be used with or without its grille in place. The grille attaches magnetically;

you can remove the grille easily by pulling it forward and replace it simply by lining up its

edges with the those of the speaker cabinet.

The logo badge on the grille can be removed, rotated 90 degrees and replaced for proper ori-

entation when using the SLX in a horizontal position. To remove the logo badge, simply push

the two pins on the rear of the logo badge together and push it out of its location on the grille.

To reinsert it, align the two pins with the hole in the grille and push the logo badge into place

(making sure the orientation of the logo badge is correct).

PLACEMENT

Your Synergy SLX speakers are designed for maximum ﬂexibility and will perform well in a

wide variety of conﬁgurations. Figure 1 shows a typical home theater setup, with a center-

channel speaker (Synergy SLX) mounted below (or above) a ﬂat panel tv, left and right front

speakers (Synergy SLX) ﬂanking the screen, and another pair of speakers (Synergy SLX) to the

sides of the listening area for the main surrounds. Below are speciﬁc placement recommenda-

tions for each function.

Center-Channel Speaker: Center the speaker directly above or below your tv and mount it on

the wall (see wall mounting instructions). When using the supplied mounting bracket, each

Synergy SLX can be rotated 30° (15° in each direction) to obtain optimal directivity toward the

listening area.

Front Left and Right Speakers: The front left and right speakers should be approximately in

line with your tv and equidistant from it. The distance from the tv is not critical, though wide

separation will tend to make the sound more spacious. Avoid having either speaker closer than

2 feet to a side wall. Place them at seated ear height if that is practical. When using the

supplied mounting bracket, each Synergy SLX can be rotated 30° (15° in each direction) to

obtain optimal directivity toward the listening area.

Left and Right Surround Speakers: Using Synergy SLX’s as surround speakers ensures an

acoustic and cosmetic match to the front left, right and center speakers. The best location for

speakers employed as surround speakers is on or against the walls to the sides of the seating

area, anywhere from adjacent to the listening position to about 20º behind it. Mount them

above the ear height of seated listeners (5’-7’ high) but avoid placing them up against or on

the ceiling. Aim them straight across the room or back slightly toward the rear wall for a more

diﬀuse sound or toward the listening position for a more direct sound. The design of the

Synergy SLX allows great flexibility and good results can be achieved with configurations that

depart significantly from the ideal. When using the supplied mounting bracket, each Synergy

SLX can be rotated 30° (15° in each direction).

Surround Back Speakers: If your electronics support Dolby Digital EX, THX Surround EX, or

DTS-ES 7.1 or 6.1-channel surround, you can place one or two speakers behind the seating

area to serve as surround back speakers. As with the left and right surrounds, the optimum

location is a bove seated ear level. If you are using just one back surround speaker, it should be

centered behind the listening area; if you are using two, they should be spaced fairly close

together. With this type of system, the regular left and right surrounds should be located

adjacent to the seating area rather than behind it

FLAT

PANEL

Optional

sub

L R

Figure 1

ENGLISH

8. Once the SLX is mounted, its angle can be ﬁne tuned to obtain optimal directivity toward the

listening area.

CAUTION: DO NOT REMOVE THE MAGNETS ON THE REAR OF THE SPEAKER ENCLOSURE.

CAUTION: SYNERGY SLX SPEAKERS ARE NOT INTENDED FOR CEILING MOUNTING.

CONNECTIONS

Note: Proper connection of your speakers to your ampliﬁer or receiver is vital to obtaining good

sound quality. Please follow these directions carefully. Sloppy connections can cause ampliﬁer

malfunction or damage.

Klipsch Synergy SLX speakers are wired internally with multiple gauges of high-purity copper wire,

carefully selected and wound to ensure optimum signal transfer at all frequencies. You will obtain

best performance from your speakers if you connect them to your amplifier or receiver with similar

quality wire available from your dealer. We recommend tha vier (lowert you use 18-gauge or hea -

gauge) stranded copper wire. Use a lower gauge (heavier) wire for longer runs to reduce the

amount of amplifier power lost due to the wire’s resistance.

BUT FIRST: TYPES OF CONNECTORS

Bare wire — Pull the two conductors apart for about an inch and strip approximately

1/4"

insula tion from the end of each. (A wire stripper will simplify this, but you can use an ordinary

pocket knife to cut around and through the insulation down to the wire.) Twist the strands of wire

on each individual conductor tightly together. Loosen the nuts on a pair of binding posts until the

holes through the metal posts are exposed, then insert the bare wire through the holes. Screw the

nuts down ﬁnger-tight on the wire. Make sure that no strands of wire are touching from one

binding post to the other or to any strands from the other conductor. Failure to observe this

precaution at either end of the connection can result in amplifier malfunction or damage.

Pins — Many pre-made speaker cables are terminated with metal pins. Loosen the nuts on a

pair of binding posts until the holes through the metal posts are exposed, then insert the pins

through the holes. Screw the nuts down ﬁnger-tight on the pins — do not over-tighten. Make

sure that there is no metal-to-metal contact between the two pins or binding posts. Failure to

observe this precaution at either end of the connection can result in amplifier malfunction

or damage.

Spade lugs — Some speaker cables are terminated with U-shaped connectors called spade

lugs. Loosen the nuts on a pair of binding posts and slip the spade lugs around the metal posts.

Screw the nuts down ﬁnger-tight on the lugs and inspect to ensure they have remained ﬁrmly

in place. Make sure that there is no metal-to-metal contact between the two lugs or binding

posts. Failure to observe this precaution at either end of the connection can result in ampliﬁer

malfunction or damage.

OTHER TYPES OF SPECIALTY CONNECTORS ARE AVAILABLE TO FACILITATE HOOKING UP YOUR

SPEAKERS. PLEASE CONSULT YOUR AUTHORIZED KLIPSCH DEALER FOR SUGGESTIONS AND

FURTHER DETAILS.

WALL MOUNTING

Each Synergy SLX speaker can be mounted vertically or horizontally. When mounted vertically, the

wall bracket can be aligned with a wall stud (in which case the supplied drywall anchors will not be

used) or simply attached to drywall (in which case the supplied dry wall anchors will be used). When

mounting the bracket horizontally, one of the two pairs of mounting holes shown in Figure 2 to be

16" apart (holes 1 and 5 or holes 2 and 6) can be aligned with wall studs that are sixteen inches

apart. Either of the two pairs can be used. Dry wall anchors and screws should then be used in the

remaining four attachment locations. If you do not wish to mount the bracket to wall studs, all six

drywall anchors and screws must be used to attach the bracket to the wall.

To install the Synergy SLX, follow these instructions:

1. Position the mounting bracket on the wall in the desired loca tion (vertical tion and orienta

or horizontal).

2. Using the mounting bracket as a template, mark the six screw locations taking care to notice the

location of wall studs. (Wall studs can be used, if desired, as stated above. However, it is not

necessary to attach the SLX bracket to wall studs.) If used in the center channel position, make

sure that the bracket is level.

3. Remove the mounting bracket and install the necessary number of supplied drywall anchors into

the wall. (Drywall anchors are not necessary in the locations where the screw will attach to a

wall stud.)

4. Route speaker wire through the mounting bracket. Wire routing channels are incorporated into

the rear of the mounting bracket. Wire can enter at any side of the bracket and will exit in the

center of the bracket directly behind the connections on the rear of the SLX as shown

in Figure 3.

5. Place the mounting bracket in the desired location and attach it to the wall by driving the

supplied screws through the bracket’s mounting holes and into the drywall anchors or wall

stud(s), making sure not to overtighten the screws.

6. Connect the speaker wire to the SLX's binding posts. See "Speaker to Ampliﬁer: Keeping it

Straight" for speaker wiring information.

7. Attach the SLX to the mounting bracket by seating the SLX's mounting slots, located on

each end of the back of the SLX, onto the mounting tabs of the bracket as shown in Figure 4.

The tabs will "click" into place when the connection is made. Lightly pull forward on the SLX to

make sure a solid connection has been made. To remove the SLX from the mounting bracket,

depress both buttons at each end of the back of the SLX and pull the speaker oﬀ of the mounting

bracket. The SLX should slide off easily . DO NOT force it. Make sure both buttons are depressed.

16"

3 4

Figure 2

MOUNTING

SLOTS

WALL

BRACKETS

Figure 4

From Ampliﬁer

Figure 3

Product specificaties

Merk:	Klipsch
Categorie:	Speaker
Model:	SLX

Heb je hulp nodig?

Als je hulp nodig hebt met Klipsch SLX stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Speaker Klipsch

Klipsch The One II McLaren Edition Handleiding

14 December 2024

Klipsch Reference R-50PM Handleiding

8 December 2024

Klipsch One Plus Handleiding

8 December 2024

Klipsch R-50PM Handleiding

8 December 2024

Klipsch R-14PM Handleiding

8 December 2024

Klipsch Promedia Heritage 2.1 Handleiding

8 December 2024

Klipsch CS-16C Handleiding

8 December 2024

Klipsch DS-180CSM Handleiding

15 November 2024

Klipsch Heritage The One Handleiding

15 November 2024

Klipsch RIC-65 Handleiding

15 November 2024

Handleiding Speaker

Nieuwste handleidingen voor Speaker

Bauhn APVK-1224 Handleiding

6 Januari 2025

Bauhn APMP-1224 Handleiding

6 Januari 2025

Akai ACS-506 Handleiding

3 Januari 2025

Akai ACS-656 Handleiding

3 Januari 2025

Akai ACS-696 Handleiding

3 Januari 2025

Philips TAS1209 Handleiding

2 Januari 2025

FoneStar SKY-8 Handleiding

2 Januari 2025

FoneStar SKY-8-DOME Handleiding

1 Januari 2025

FoneStar SKY-8T-DOME Handleiding

1 Januari 2025

Creative Pebble Nova Handleiding

1 Januari 2025