KLH Audio Concord Handleiding

KLH Audio Speaker Concord

Lees hieronder de 📖 handleiding in het Nederlandse voor KLH Audio Concord (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 75 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

FLOORSTANDING

LOUDSPEAKERS

KENDALL CONCORD

MANUAL

WELCOME!

Thank you for purchasing one of the best sounding loudspeakers

ever produced. At KLH, we have been making high-quality com-

ponents since 1957, and we take pride in making your music and

movies the best experience possible.

FOR YOUR SAFETY

Important Safety Instructions!

1. READ these instructions.

2. KEEP these instructions.

3. HEED all warnings.

4. FOLLOW all instructions.

5. DO NOT use this apparatus near water.

6. CLEAN with dry cotton cloth. Do not use microfiber.

7. DO NOT block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other heat producing appliances

9. USE ONLY attachments/accessories specified by

the manufacturer.

10. DO NOT expose to excess moisture or liquids, and do not

place containers with liquids on top of speakers.

The exclamation point, within an equilateral triangle, is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the product.

The lightning flash with arrowhead symbol within an

equilateral triangle is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electrical shock to persons.

EU COMPLIANCE INFORMATION:

Eligible to bear the CE mark, Conforms to European Union EMC

Directive 2004/108/EC; European Union Restriction of Hazard-

ous Substances Recast (RoHS2) Directive 2011/65/EC; European

Union WEEE Directive 2002/96/EC.

KLH and the KLH logo are registered trademarks of Kelley Global

Brands Inc., registered in the U.S. and other countries.

WEEE NOTICE

Note: This mark applies only to countries within the European

Union (EU) and Norway.

This appliance is labeled in accordance with European

Directive 2002/96/EC concerning waste electrical and

electronic equipment (WEEE). This label indicates that

this product should not be disposed of with household

waste. It should be deposited at an appropriate facility

to enable recovery and recycling.

CONTENTS:

This package should contain 2 sets (4 each) of feet. The rubber feet

are used for solid flooring such as wood, tile and concrete, and the

chrome-plated spikes are used for carpet. Spikes may be used on

solid flooring when placed on chrome plated isolation discs.

UNPACKING

Place the package on the floor with the box flaps up. Cut the tape

with a utility knife to open the package. Fold the carton flaps back

and carefully slide the speaker and packaging from the box, or turn

the box over with flaps open and remove the box. Stand the speak-

er and packing upright, making sure the loudspeaker plinth is on the

bottom, and remove the packing material.

C A NU T I O

R K OF ELECTRIC SHOCK. IS

DO NOT OPEN.

WARNING: Do Not Open! Risk of Elec ical Shock. Voltages in this tr

equi ent are hazardous to life. No user-servi ble parts in de. pm cea si

Refer all servicing to aliﬁed service personnel. qu

SPIKE AND RUBBER FEET

LIst of items included in package (per speaker):

Spiked and rubber feet are to be used for bass decoupling

(reducing bass transmission) and should only be used when

plinth is on the bottom of the speaker. To install metal

spiked feet, you may place speaker on the floor on either

side. DO NOT place speaker front on floor, as this may

physically damage the tweeter guard and/or dome. First

thread ridged discs onto the metal spikes until flush. Follow

by threading both into the insert at the bottom corners of

the plinth. To level the speaker, height may be adjusted by

turning the spike section ONLY.

To avoid damage to floors other than carpet, the metal

spike can be used with protective ring as shown above on

the far right. Threaded rubber feet can be used on virtually

all surfaces. Installation is shown below.

ROOM POSITION

Placement of your floorstanding loudspeakers is a personal

preference, but it is recommended that speakers be placed at

least 6 feet apart whether they are being used for a stereo

application, or as the main left and right channels for a home

theater. For best imaging and separation, listening distance from

the speakers should be about 1.5 times the distance the speakers

are apart from each other.

Example: If the distance between each speaker and the listening

position is 9 feet, then the speakers should be 6 feet apart from

one another. Be sure that loudspeakers are placed at least 12

inches away from any wall. Further adjustments can be made to

optimize your listening experience.

AMPLIFICATION

Conventional amplification involves a single stereo amplifier

wired to a single set of binding posts with straps connecting the

second set of posts as seen in diagram above. Simply attach the

positive wire + to the red post, and the negative wire – to the

black post.

BI-AMPLIFICATION

This connection method (see diagram below) uses two separate

two channel amplifiers to power one set of speakers. One amplifier

is attached to one set of binding posts, and another identical

amplifier is attached to the other set of binding posts. This is

referred to as bi-amplification.

Be sure to remove the terminal

straps before using the bi-amplifi-

cation method. Connect positive

+ and negative – cables from the

amplifier to the top terminals,

and make sure the connection is

tight. Connect the second set of

cables (positive and negative) to

the bottom terminals and tighten.

Repeat these same steps using the

second amplifier to connect to

the second terminals.

NOTE: The Concord Floorstander has a single set of

binding posts, and this bi-amplification method is

not applicable.

CONNECTING YOUR

FLOORSTANDING LOUDSPEAKERS

Both floorstanding loudspeakers have the same quality nick-

el-plated binding posts that will accommodate stripped wire,

spade connectors or banana plugs. Be

sure to use quality speaker cables, up

to 12 gauge (AWG). The lowest gauge

possible is recommended. Before using

banana plugs, be sure to remove the

black and red inserts on the binding

posts. The straps connecting the binding

posts should remain in place for conven-

tional wiring, but may be removed where

bi-wiring is preferred. See the following

diagrams in the AMPLIFICATION section

for further instruction.

LEFT

SUB

RIGHT

CENTER

SURROUND

LEFT

SURROUND

RIGHT

PORT TUNING

If placing your floorstanding loudspeakers 6 inches or closer to a

wall, bass output can be controlled by reducing the amount of air

flow from rear ports. You can “tune” bass output by using the tuning

stops provided with your loudspeaker by inserting as shown.

NOTE: When moving

loudspeakers take extra

caution to place hands in a

position that will not

damage the drivers. This

can best be done by

placing one hand in the

port at the back of the

loudspeaker, and the other

hand at either top corner.

ALWAYS KEEP HANDS AWAY FROM TWEETER TO AVOID DAMAGE.

WARRANTY

Our 10 year warranty begins from purchase date of the item.

(Receipt Date) Warranty registration must be completed at

KLHAUDIO.com/warranty. Registration of the product must be

completed within 120 days of purchase for warranty validation.

Original receipt of purchase must be retained for proof of

purchase. For warranty or service issues, please contact authorized

KLH dealer. The warranty covers any production and/or material

defects of the product. This warranty is non-transferable.

The following is NOT COVERED by the warranty:

1. Accidents, misuse, poor maintenance, electrical overloads such

as lightning or voltage.

2. Incorrect use of product.

3. Altered serial number.

4. Transportation costs for service call.

5. Purchase of KLH products from unauthorized reseller.

Replacement item cannot exceed the cost of the item under

warranty. The supplier is responsible for only repair or

replacement. KLH toll free number is 1-833-554-8326

Product specificaties

Merk:	KLH Audio
Categorie:	Speaker
Model:	Concord

Heb je hulp nodig?

Als je hulp nodig hebt met KLH Audio Concord stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Speaker KLH Audio

KLH Audio Albany II Handleiding

9 Januari 2024

KLH Audio Quincy Handleiding

9 Januari 2024

KLH Audio Kendall 2C Handleiding

9 Januari 2024

KLH Audio Concord Handleiding

9 Januari 2024

KLH Audio Cambridge Handleiding

9 Januari 2024

KLH Audio Kendall Handleiding

9 Januari 2024

KLH Audio Kendall 2S Handleiding

9 Januari 2024

KLH Audio Kendall 2F Handleiding

9 Januari 2024

KLH Audio Beacon Handleiding

9 Januari 2024

KLH Audio Model Three Handleiding

9 Januari 2024

Handleiding Speaker

Nieuwste handleidingen voor Speaker

Canton GLE 476 Handleiding

17 November 2024

Berker 29807009 Handleiding

17 November 2024

Berker 29807006 Handleiding

17 November 2024

Berker 30801606 Handleiding

17 November 2024

Berker 29806086 Handleiding

17 November 2024

Berker 30809909 Handleiding

17 November 2024

Berker 29801606 Handleiding

17 November 2024

Berker 30808989 Handleiding

17 November 2024

Berker 29807003 Handleiding

17 November 2024

Berker 30806089 Handleiding

17 November 2024