Klein Tools Scout 3 Pro Handleiding

Klein Tools Meetapparatuur Scout 3 Pro

Lees hieronder de 📖 handleiding in het Nederlandse voor Klein Tools Scout 3 Pro (28 pagina's) in de categorie Meetapparatuur. Deze handleiding was nuttig voor 7 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/28
VDV501-851
VDV ScoutTM Pro 3
ESPAÑOL pág. 11
FRANÇAIS p. 20
INSTRUCTION MANUAL
• VOICE, DATA, AND VIDEO CABLE TESTING
• DETECTS SHORT FAULTS, OPEN FAULTS,
REVERSALS, MISWIRES, CROSSOVER
WIRING AND SPLIT PAIRS
• CABLE ID
• LENGTH MEASUREMENT
• TONE GENERATOR
• EXTRA-LARGE BACKLIT LCD
• HUB BLINK
• AUTO POWER-OFF
ENGLISH pg. 2
MANUEL D’UTILISATION
MANUAL DE INSTRUCCIONES
• VÉRIFICATION DE CÂBLES POUR VOIX, DONNÉES ET VIDÉOS
• DÉTECTION DES COURTS-CIRCUITS, DES COUPURES, DES
INVERSIONS, DES MAUVAIS RACCORDEMENTS,
DES CROISEMENTS ET DES PAIRES DIVISÉES
• IDENTIFICATION DE CÂBLE
• MESURE DE LA LONGUEUR
• GÉNÉRATEUR DE TONALITÉ
• TRÈS GRAND ÉCRAN ACL RÉTROÉCLAIRÉ
• CLIGNOTANT DU CONCENTRATEUR
• ARRÊT AUTOMATIQUE
• PRUEBA DE CABLES DE VOZ, DATOS YVIDE
• DETECTA FALLAS DECORTOCIRCUITO,
FALLAS DE CIRCUITO ABIERTO,
INVERSIONES, ERRORES DE CABLEADO,
CABLEADO CRUZADO Y PARES DIVIDIDOS
• ID DE CABLE
• MEDICIÓN DE LONGITUD
• GENERADOR DE TONO
• PANTALLA LCD EXTRAGRANDE
RETROILUMINADA
• PARPADEO DEL CONCENTRADOR
• FUNCIÓN DE APAGADO AUTOMÁTICO
1 2 34567 8
ID
Pas Res X-over v
Fai horl S t Split Open
Shielded
ft
m
2
GENERAL SPECIFICATIONS
The Klein Tools VDV Scout
TM
Pro 3 is a portable voice-data-video cable tester. It tests and troubleshoots RJ11,
RJ12, RJ45, and F-connector terminated cables and provides tone generation for cable tracing. The VDV Scout
TM
Pro 3 also measures cable length, tests for shield, performs hub blink testing, and traces up to 19 locations (up to
5 locations with included remotes, additional remotes available separately).
PORTS AND REMOTES OVERVIEW
• Dimensions: 6.5" x 3.0" x 1.6" (16.5 x 7.6 x 4.1 cm)
• Weight: 11 oz. (312 g) with battery and remote
• Operating Temperature: 32° to 122°F (0° to 50°C)
• Storage Temperature: -4° to 140°F (-20° to 60°C)
• Humidity: 10% to 90%, non-condensing
• Maximum Voltage (between any two connector
pins without damage):
- RJ Jack: 66V DC or 55V AC
- F-Connector: 66V DC or 55V AC
• Battery Life (9V alkaline):
- Standby: 4 years
- Active: 50 hours (without backlight)
• Cable Types: Shielded or unshielded; Cat7a, Cat7, Cat6a,
Cat6, Cat5e, Cat3, Coaxial
• Length Measurement Method: Capacitance
• Length Measurement Range:
1.5 ft to 1,999 ft. (0.5 m to 610 m) with 15pF/ft
• Length Accuracy:
(5% ft.) or (5% m)
• Length Constant Range:
10pF/ft. to 40pF/ft. (33pF/m to 132pF/m)
WARNINGS
To ensure safe operation and service of the tester, follow these instructions. Failure to observe these
warnings can result in severe injury or death.
• The VDV ScoutTM Pro 3 is designed for use on unenergized cabling systems. Connecting the VDV Scout
TM Pro
3 to live AC power may damage it and pose a safety hazard for the user.
• Improperly terminated RJ plugs have the potential to damage the jacks on the VDV Scout
TM Pro 3. Visually
inspect an RJ plug before inserting it into the tester. The contacts should always be recessed into the plastic
housing of the plug. Plugging 6-position plugs into the 8-position jack on the tester has the potential to
damage the outer-most contacts of the jack unless the plug is specifically designed for that purpose.
SYMBOLS ON TESTER
Warning or Caution Do use on energized circuitsNOT
Always wear approved eye protection Read instructions
Conformité Européenne - Conforms with European Economic Area directives
UKCA: UK Conformity Assessment
This symbol indicates that equipment and its accessories shall be subject to a separate
collection and correct disposal
RJ45 Port: Data cable, Ethernet cable, Cat5e, Cat6, Cat6a, Cat7, Cat7a.
F-Connector Port: Video cable, coaxial cable, RG6/RG6Q cable, RG59 cable.
RJ11/12 Port: Voice cable, POTS (plain old televoice service) cable, 4-wire cable, 6-wire cable,
2 twisted pair cable, 3 twisted pair cable, Cat3.
VDV SCOUTTM
PRO 3 TESTER LOCATION ID REMOTES
F-connector port
RJ11/12 port*RJ45 port*
Use for cable location identification mapping.
Set #1–5 included with VDV500-851, set #1–18
included with VDV501-852 and sold separately.
ENGLISH
LanMap™
Location ID Remote**
VDV526-055
RJ45
connector
**Cannot be used to perform wire map or
cable length tests.
*The RJ jacks share internal connections so only one RJ cable can be connected at a time for accurate cable
test results. However, an RJ cable and a coax cable may be connected at the same time. In ID mode, all
connectors on the VDV ScoutTM Pro 3 may be connected at the same time.
CONNECTORS
Barrel Connector
VDV814-609
Female-to-female F-connector
Use with F-connector port
CoaxMap™
Location ID Remote**
VDV512-056
F-connector
3
ENGLISH
SELF-STORING TEST + MAP™ ID REMOTE (VDV501-210)
TEST + MAP™ ID REMOTES (VDV501-2## SERIES)
Use for cable location identification mapping and/or continuity testing. Self-storing remotes display
on tester as Remote ID #1. Included with all VDV Scout
TM
Pro 3 models.
Use for cable location identification
mapping and continuity testing.
Remotes display on tester asRemote
IDs #1-12. Set #2–6 included with
VDV500-853 and sold separately,
set #7–12 sold separately, individual
remotes #1–12 each sold separately.
RJ11/12
port RJ45
port
F-connector
port
KEYPAD FUNCTION
• VOICE / UP BUTTON
A
: Performs wiremap test on RJ11/RJ12
terminated cable, toggles selection upward in other modes.
• VIDEO BUTTON
B
: Performs continuity test on F-terminated coax cable.
• DATA / DOWN BUTTON
C
: Performs wiremap test on RJ45
terminated cable, toggles selection downward in other modes.
• TONE / HUB BLINK BUTTON
D
: Cycles through available
tone cadences, initiates Hub Blink.
• SETTINGS BUTTON
E
: Selects feet or meters,
enters Length Constant Edit mode.
• PoELENGTH / BUTTON
F
: Measures cable length, initiates PoE test.
• POWER / BACKLIGHT BUTTON
G
: Turns unit on or off, turns backlight on or off.
A
D
G
F
E
B C
• VOICE / UP BUTTON
A
: Short Press: Initiates wiremap test on RJ11/RJ12 terminated cable. When in Tone or Length
Test mode, the first short press selects Voice mode, repeated short presses selects wires orpairs of wires. Long press:
Turns Loop mode on or off. When in Tone or Length Test mode, returns to home screen. When in Settings mode,
changes UOM from feet to meters, or increases the length contant value.
• VIDEO BUTTON
B
: Short Press: Initiates continuity test on an F-terminated coax cable.
When in Tone or Length Test
mode, a short press selects Video mode.
Long press:
Turns Loop mode on or off. When in Tone or Length Test mode,
returns to home screen.
• DATA / DOWN BUTTON
C
:
Short Press: Initiates wiremap test on RJ45 terminated cable. When in Tone or Length Test mode, first short press
selects Data mode, repeated short presses select wires or pairs of wires. Turns Loop mode on or off. Long press:
When in Tone or Length Test mode, returns to home screen. When in Settings mode, changes UOM from feet to meters,
or increases the length contant value.
• TONE / HUB BLINK BUTTON
D
: Short Press: Repeated short presses will toggle through available tone cadences.
Long press: Initiates Hub Blink.
NOTE DO NOT: attempt to use Hub Blink function when connected to a Power over
Ethernet (PoE) active port.
• SETTINGS BUTTON
E
: Short Press: Enters Length Constant edit mode (use the UP
A
and DOWN
C
buttons to
adjust value). Default for Length Constant mode is the wire pair of pins 1 and 2 of data/RJ45 cable, and the wire pair
of pins 3 and 4 of voice/phone cable. See LENGTH CONSTANT Second short press: section for more details. Displays
option of feet or meters (use the UP
A
and DOWN
C
buttons to change). See section for LENGTH MEASUREMENT
details. Long press: Exits Settings mode and returns to home screen.
• PoELENGTH / BUTTON
F
: Short Press: Initiates cable length test. Test will default to a cable connected to the RJ45
port. By default, the test will initiate on the first wire with no faults found. See and LENGTH MEASUREMENT LENGTH
CONSTANT sections for more details.
Long press: Initiates PoE test.
• POWER / BACKLIGHT BUTTON
G
: Short Press: First short press turns unit on, repeated short presses will turn
thebacklight on and off. Press the power button a second time to turn the LCD backlight on or off.
Long press: Turns unit off.
NOTE: Unit will automatically power off after 5 minutes of inactivity, or after 60 minutes
when in Tone mode.
IN DETAIL
QUICK-REFERENCE
RJ45
port F-connector
port

Product specificaties

Merk: Klein Tools
Categorie: Meetapparatuur
Model: Scout 3 Pro

Heb je hulp nodig?

Als je hulp nodig hebt met Klein Tools Scout 3 Pro stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Meetapparatuur Klein Tools

Klein Tools

Klein Tools NCVT-6 Handleiding

18 November 2024
Klein Tools

Klein Tools ET19 Handleiding

12 November 2024
Klein Tools

Klein Tools VDV501-770 Handleiding

24 September 2024
Klein Tools

Klein Tools ET18 Handleiding

21 September 2024
Klein Tools

Klein Tools VDV211-048 Handleiding

21 September 2024
Klein Tools

Klein Tools ET500 Handleiding

18 Juni 2024
Klein Tools

Klein Tools ET510 Handleiding

18 Juni 2024
Klein Tools

Klein Tools NCVT-3 Handleiding

18 Juni 2024
Klein Tools

Klein Tools NCVT-2 Handleiding

18 Juni 2024
Klein Tools

Klein Tools 45001 Handleiding

17 Mei 2024

Handleiding Meetapparatuur

Nieuwste handleidingen voor Meetapparatuur

PCE Instruments

PCE Instruments PCE-PST 1 X Handleiding

16 December 2024
Steinberg

Steinberg SBS-LF-147 Handleiding

15 December 2024
Steinberg

Steinberg SBS-SM-135C Handleiding

15 December 2024
Steinberg

Steinberg SBS-MT-100 Handleiding

15 December 2024
Steinberg

Steinberg SBS-SM-130C Handleiding

15 December 2024
Steinberg

Steinberg SBS-DT-999 Handleiding

15 December 2024
Steinberg

Steinberg SBS-DL-123D Handleiding

15 December 2024
Steinberg

Steinberg SBS-LF-141 Handleiding

15 December 2024
Steinberg

Steinberg SBS-LF-140 Handleiding

15 December 2024
Steinberg

Steinberg SBS-LF-116 Handleiding

15 December 2024