Klein Tools CL810 Handleiding

Klein Tools Meetapparatuur CL810

Lees hieronder de 📖 handleiding in het Nederlandse voor Klein Tools CL810 (27 pagina's) in de categorie Meetapparatuur. Deze handleiding was nuttig voor 4 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/27

INSTRUCTION MANUAL

ENGLISH

FRANÇAIS p. 33

ESPAÑOL pg. 17

600A AC/DC Auto-Ranging

Digital Clamp Meter

True RMS

Measurement

Technology

• NON-CONTACT

VOLTAGE TESTER

• LOW IMPEDANCE

• DATA & RANGE HOLD

• AUDIBLE CONTINUITY

• DIODE TEST

• CAPACITANCE & FREQUENCY

• TRANSFLECTIVE

REVERSE-CONTRAST DISPLAY

• LIGHTED DIAL

CL810

mIP40

-40° – 1832°F

(-40° – 1000°C)

5000573

CAT IV

600V

CAT III

1000V

GENERAL SPECIFICATIONS

Klein Tools CL810 is an automatically ranging true root mean square

(TRMS) digital clamp-meter that measures AC/DC current via the clamp,

measures AC/DC voltage, resistance, continuity, frequency, inrush,

capacitance, and tests diodes via test-leads, and temperature via a

thermocouple probe. It also features a Low Impedance (LoZ) mode for

identifying and eliminating ghost or stray voltages, transflective reverse-

contrast display, and lighted dial.

• Environment: Indoor: Do not expose to moisture, rain or snow.

• Operating Altitude: 6562 ft. (2000m)

• Relative Humidity: <80% non-condensing

• Operating Temp: ° ° ° °32 to 122 F (0 to 50 C)

• Storage Temp: ° ° ° °14 to 140 F (-10 to 60 C)

• Accuracy: Values stated at 65° to 83°F (18° to 28°C)

• Temp Coefcient: ° °0.1 × (Quoted Accuracy) per C above 28 C

or below 18 C, corrections are required when ambient working °

temp is outside of Accuracy Temp range

• Auto Power-Off (APO): After 5 minutes of inactivity (unless

disabled)

• Dimensions: 9.06" × 3.47" × 1.65" (230 × 88 × 42 mm)

• Weight: 13 oz. (369 g) including batteries

• Calibration: Accurate for one year

• Standards:

IEC EN 61010-1, 61010-2-032.

Conforms to: UL STD 61010-1, 61010-2-032.

Certied to: CSA STD C22.2 #61010-1, 61010-2-032.

• Pollution degree: 2

• Accuracy: ± (% of reading + # of least significant digits)

• Drop Protection: 6.6 ft. (2m)

• Safety Rating: CAT IV 600V, CAT III 1000V, Class 2,

Double insulation

CAT III: Measurement category III is applicable to test and

measuring circuits connected to the distribution part of the

building’s low-voltage MAINS installation.

CAT IV: Measurement category IV is applicable to test and

measuring circuits connected at the source of the building’s

low-voltage MAINS installation.

• Electromagnetic Environment: IEC EN 61326-1. This

equipment meets requirements for use in basic and controlled

electromagnetic environments like residential properties,

business premises, and light-industrial locations.

Specifications subject to change.

ENGLISH

5000573

ELECTRICAL SPECIFICATIONS

Function Range Resolution Accuracy

Frequency

(Auto-

Ranging)

1.000Hz to 9.999Hz 0.001Hz

±(1.0% + 5 digits)

99.99Hz 0.01Hz

999.9Hz 0.1Hz

9.999kHz 1Hz

99.99kHz 10Hz

500.00kHz 100Hz

Sensitivity: >2V to 220V RMS

Maximum Input: 1000V AC RMS or 1000V DC

Duty Cycle

1.0% to 99.9%

0.1%

±(1.2% + 2 digits)

Pulse width: Frequency width: >100µs, <100ms 5Hz to 10kHz

Sensitivity: >2V to 220V RMS 1000V DC or 1000V AC RMSMaximum Input:

Inrush

Current 600.0A 100mA ±(3.0% + 8 digits)

Frequency Range: Detection Range: 50 to 60Hz >2A

OTHER MEASUREMENT APPLICATIONS

Maximum Input: 1000V AC RMS or 1000V DC

• Diode Test: Max. 1.5mA, open circuit voltage ~3.2V DC

• Audible signal <50Ω, test current <1.5mAContinuity Check:

• 4 samples per secondSampling Frequency:

• Input impedence >3kΩ, Low Impedence (Low Z):

Max input 1000V AC RMS or 1000V DC RMS

• Auto Power-Off: After ~5 minutes of inactivity

• Overload: "OL" indicated on display, overload protection 1000V in all settings

• "-" on display indicates negative polarityPolarity:

• 3-5/6 digit, 6000 Count LCDDisplay:

ENGLISH

WARNINGS - GENERAL

To ensure safe operation and service of the meter, follow these instructions.

Failure to observe these warnings can result in severe injury or death.

• Before each use verify meter operation by measuring a known voltage

or current.

• Never use the meter on a circuit with voltages that exceed the category

based rating of this meter.

• Do not use the meter during electrical storms or in wet weather.

• Do not use the meter or test leads if they appear to be damaged.

• Use only with CAT III 1000V/CAT IV 600V rated test leads or better.

• Ensure meter leads are fully seated, and keep fingers away from the

metal probe contacts when making measurements.

• Use caution when working with voltages above 25V AC RMS or 60V DC.

Such voltages pose a shock hazard.

• To avoid false readings that can lead to electrical shock, replace batteries

when a low battery indicator appears.

• Do not attempt to measure resistance or continuity on a live circuit.

• Always adhere to local and national safety codes. Use personal protective

equipment to prevent shock and arc blast injury where hazardous live

conductors are exposed.

• To avoid risk of electric shock, disconnect leads from any voltage source

before removing battery door.

• To avoid risk of electric shock, do not operate meter while battery door is removed.

WARNINGS

Product specificaties

Merk:	Klein Tools
Categorie:	Meetapparatuur
Model:	CL810

Heb je hulp nodig?

Als je hulp nodig hebt met Klein Tools CL810 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Meetapparatuur Klein Tools

Klein Tools CL710 Handleiding

13 Januari 2025

Klein Tools CL810 Handleiding

13 Januari 2025

Klein Tools NCVT-6 Handleiding

18 November 2024

Klein Tools ET19 Handleiding

12 November 2024

Klein Tools VDV501-770 Handleiding

24 September 2024

Klein Tools ET18 Handleiding

21 September 2024

Klein Tools VDV211-048 Handleiding

21 September 2024

Klein Tools ET500 Handleiding

18 Juni 2024

Klein Tools ET510 Handleiding

18 Juni 2024

Klein Tools NCVT-3 Handleiding

18 Juni 2024

Handleiding Meetapparatuur

Nieuwste handleidingen voor Meetapparatuur

PCE Instruments PCE-ACO 9500 Handleiding

13 Januari 2025

PCE Instruments PCE-TC 32N Handleiding

13 Januari 2025

PCE Instruments PCE-324 Handleiding

13 Januari 2025

PCE Instruments PCE-PMI 1 Handleiding

13 Januari 2025

Ebro PHT 830 Handleiding

13 Januari 2025

Gossen Metrawatt PROFiTEST H+E EASY CHECK Handleiding

9 Januari 2025

TFA 40.1046 Handleiding

8 Januari 2025

TFA SANDY 40.1043.06 Handleiding

8 Januari 2025

TFA 40.1058.11 Handleiding

8 Januari 2025

PCE Instruments PCE-FST-200-201-H-I Handleiding

8 Januari 2025