Kicker 46HDS144 Handleiding

Kicker Hifi systeem 46HDS144

Lees hieronder de 📖 handleiding in het Nederlandse voor Kicker 46HDS144 (19 pagina's) in de categorie Hifi systeem. Deze handleiding was nuttig voor 74 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/19

PROGRAMMING HD RADIO

NOTE: It is necessary to re-ﬂ ash your HD radio before installation of this kit. If you do not have the Techno Research Centurion program software you may purchase a Kicker TRHDP Radio

Flash Programmer.

GETTING STARTED

1. Remove the seat and disconnect both negative and positive battery terminals.

2. Remove the windshield.

3. Remove the outer fairing.

a. Remove the four mounting screws, unplug the headlamp and set aside on a soft cloth.

4. Remove the fuel tank.

a. Unplug the fuel ﬁ tting on the left side of the tank. You may remove the console if you want to retain vent line routing and connector placement.

b. Remove all four mounting bolts and carefully lift the tank off the bike and set aside.

5. Remove wire caddy cover.

a. Carefully release each tab along the caddy until it lifts completely.

SPEAKER INSTALLATION

6. Remove one of the white speaker pods from the inner fairing. (Fig. 1)

a. There are ﬁ ve fasteners in the center portion and three on the outside to release it from the inner fairing.

7. Remove the stock speaker and replace with the PSC652 speaker from the kit.

a. Install the provided speaker ring adapter onto the speaker pod. (Fig. 2)

b. Install the speaker into the pod and fasten with the original speaker screws. (Fig. 3)

8. Reinstall the pod to the inner fairing.

9. Repeat for the other side.

AMP INSTALLATION

If you have a 2020 Street or Tri Glide, the following steps must be completed before ampliﬁ er installation:

Remove four screws from the HD Connect Module. Remove Module from Bracket. Relocate Module to the clutch side of the radio and secure with two 8” zip ties included. (Fig. 4 and Fig 5.)

NOTE: There may be some connectors that will need to be relocated off of the radio chassis for the amp bracket to ﬁ t.

10. Fasten the ampliﬁ er to the bracket with the supplied hardware.

a. Insert the bolts through the bottom of the bracket and install the locknuts to the ampliﬁ er.

11. At this time, it is highly recommended to set the amp gain setting to 0. KICKER recommends that the dip switches be set up as follows :(Fig 6)

Auto turn-on - 12V Input level - HI Amp1: HI-PASS – 80 Hz Input Gain control – 0  

Fader - ON Amp2: HI-PASS – 60 Hz (6x9) 

80 Hz (6.5” Tour Pack)

12. After ﬁ nishing System Setup, use the supplied ¼” hardware and fasten the amp/bracket assembly to the radio chassis with the 10-pin connector and power connector facing the throttle

side. (Fig. 7)

HARNESS INSTALLATION

13. Plug the harness into the ampliﬁ er and route the speaker wires to their respective locations. (Fig. 8)

a. Separate the speaker connectors and plug in the ampliﬁ er harness to each speaker.

14. Plug the 4-pin male, rear audio connector into the 4-pin female rear audio signal connector coming from the radio harness. and(Fig. 9 Fig. 10)

15. Plug the switched power harness into the 2-pin amp connector on the throttle side of the fairing. (Fig. 11)

16. Plug the blue wire on the kicker harness into the switched power harness lead with one wire.

a. This allows for an accessory 12V port to remain available.

17. Route the power leads along the clutch side of the frame neck, in the electrical caddy to the seat area. (Fig. 12)

NOTE: If you are not running rear speaker lids or tour pack, please plug in the Dummy Load Plug into the ampliﬁ ed rear speaker output at the end of the harness. (Figs. 13, 14, 15)

18. Reconnect the battery terminals and pull the excess harness slack back into the fairing. Create a slack loop with excess harness slack.

19. Plug the radio in, and set the gain.

20. Test component function and set the gain to optimize system performance.

21. Carefully reassemble the motorcycle and enjoy your new audio kit!

46HDS144

Motorcycle Audio Kit Installation Guide for Harley Davidson®

Electra Glide | Street Glide | Ultra Glide | Bat Wing Trikes

2014–Newer (FLHT)

Package Contents:

(1) Install Guide (1) Wiring Harness (4) Black Cable Ties (2) 6-1/2” KICKER Speakers & Grilles

(4) 8-32 x 1/2” Button Head Bolts (1) Stainless Steel Mounting Bracket (1) 75W x 4 KICKER Amp (4) 8-32 Nylock Nuts

(1) Mounting Hardware (3) 1/4” 20 washers (3) 1/4” 20 1” bolts (3) 1/4” 20 Nylock Nuts

(1) Dummy Load Plug

Important: Over-tightening mounting fasteners may result in damage to your motorcycle. Please refer to your service manual for proper

procedures and torque speciﬁ cations. KICKER is not responsible for damage resulting from improper installation techniques. This kit be compatible with some aftermarket head units.may not

FRONT KIT PROGRAMMING WITH KICKER TRHDP

Follow instructions included with KICKER TRHDP

FRONT & REAR KIT PROGRAMMING WITH KICKER TRHDP

Follow instructions included with KICKER TRHDP

KICKER cannot be held responsible for any damage to painted surfaces during removal or addition of KICKER parts. 46HDS144-F-20200305

123 4

5 6 7 8

910 11

12 13 14 15

For questions, please contact KICKER Technical Support at 800-256-0808, M-F 8:00 am – 5:00 pm CST or email at support@kicker.com. For installation videos please go to our

Kicker YouTube channel.