Kicker 46HDR154 Handleiding

Kicker Hifi systeem 46HDR154

Lees hieronder de šŸ“– handleiding in het Nederlandse voor Kicker 46HDR154 (21 pagina's) in de categorie Hifi systeem. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/21
PROGRAMMING HD RADIO
NOTE: It is necessary to re-ļ¬‚ ash your HD radio before installation of this kit. If you do not have the Techno Research Centurion program soft-
ware you may purchase a Kicker TRHDP Radio Flash Programmer.
GETTING STARTED
1. Remove the seat and disconnect both positive and negative battery terminals.
2. Remove the windshield and outer fairing.
a. Once the windshield screws are removed, gently pull off the top vent/cowl piece. There are two plastic retainer clips that hold it on.
b. Remove your stock speaker grilles. Push them out from the inside of the fairing. They are fastened with a plastic retainer clip. Fig 1.
c. Unplug the turn signals. Fig 2.
d. Remove the lower T25 fasteners holding the air deļ¬‚ ectors to the inner fairing. Fig 3.
e. Remove the 3/16ā€ allen bolts holding the turn signals to the inner fairing. Fig 4.
f. While holding the fairing, carefully remove the two T30 bolts behind the speaker grilles to remove the outer fairing and set aside. Fig 5.
3. Remove the fuel tank.
a. Remove the console.
b. Unplug the fuel ļ¬ tting on the left side of the tank.
c. Remove all four mounting bolts and carefully lift the tank off the bike and set aside.
4. Remove wiring caddy cover.
a. Carefully release each tab along the caddy until it lifts completely. Fig 6.
SPEAKER INSTALLATION
5. Remove your stock speakers and replace them with your new PSC652 speakers in the kit.
a. Install the provided speaker ring adapter onto the speaker pod. Fig 7.
b. Install the speaker into the pod and fasten with the original speaker screws. Fig 8.
AMP INSTALLATION
6. Remove the radio.
a. Unplug the four connectors on the back of the radio.
b. Remove the four allen head bolts holding the radio to the chassis.
c. Gently remove the radio from the chassis.
7. Install the PXA300.4 ampliļ¬ er onto bracket with supplied hardware. Fig 9.
a. Slide the end of the ampliļ¬ er with the power connector port into the bracket and fasten with supplied hardware.
b. Install the bolts from the bottom and fasten the locknuts onto the ampliļ¬ er.
8. Carefully install bracket/ampliļ¬ er assembly onto radio chassis by installing the assembly through the radio face port in the fairing and sliding
the tabs of the bracket over the chassis. Fig 10.
a. The amp bracket assembly mounts under the radio.
HARNESS INSTALLATION
9. Plug the harness into the ampliļ¬ er and route speaker wires to their respective connectors. Fig 11.
a. Separate the speaker connectors and plug in the ampliļ¬ er harness to each speaker.
46HDR154
Motorcycle Audio Kit Installation Guide for
Harley DavidsonĀ® Road Glide (FLTR) 2015ā€“Newer
Package Contents:
(1) Install Guide (1) Wiring Harness (4) Black Cable Ties
(2) 6-1/2ā€ KICKER Speakers (2) 8-32 x 1/2ā€ Button Head Bolts (1) Ampliļ¬ er Mounting Bracket
(1) 75W x 4 KICKER Amp (2) 8-32 Nylock Nuts (1) Dummy Load Plug
Important: Over-tightening mounting fasteners may result in damage to your motorcycle. Please refer to your service manual for proper
procedures and torque speciļ¬ cations. KICKER is not responsible for damage resulting from improper installation techniques. This kit may not
be compatible with some aftermarket head units.
FRONT KIT PROGRAMMING WITH KICKER TRHDP
Follow instructions included with KICKER TRHDP
FRONT & REAR PROGRAMMING WITH KICKER TRHDP
Follow instructions included with KICKER TRHDP
10. Plug the switched power harness into the 2-pin amp connector on the throttle side. Fig 12.
11. Plug the blue wire on the kicker harness into the switched power harness lead with one wire.
a. This allows for an accessory 12V port to remain available.
12. Route both power leads along the clutch side of the neck and through the electrical caddy to the seat area.
13. Reconnect the battery terminals.
NOTE: If you are not running rear speaker lids or tour pack, please plug in the Dummy Load Plug into the ampliļ¬ ed rear speaker output at the
end of the harness. (Fig.13)
SYSTEM SETUP - Fig 9.
Note: At this time, it is highly recommended to . KICKER recommends that the be set up as follows:set the amp gain to 0 dip switches
Auto turn-on ā€“ 12V Input level ā€“ HI HI-PASS ā€“ Amp 1: 80 Hz (For Front) Input Gain controls ā€“ 0ļƒ‡ ļƒˆ ļƒˆļƒˆ
Fader ā€“ On Amp 2: 60Hz (6 x 9) ļƒˆ ļƒ‡ļƒˆ
80Hz (6.5ā€ Tour Pack)ļƒˆļƒˆ
14. Plug the radio in, but do not reinstall it until the gain has been set.
15. Test component function and set the gain to optimize system performance.
16. Carefully reassemble the motorcycle and enjoy your new audio system!
For questions, please contact KICKER Technical Support at 800-256-0808, M-F 8:00 am ā€“ 5:00 pm CST or email at support@kicker.com.
For installation videos please go to our Kicker YouTube channel.
KICKER cannot be held responsible for any damage to painted surfaces during removal or addition of KICKER parts. 46HDR154-D-20200228
123 4
56
78
9
10
11
12
13
PXA 4-CHANNEL AMPLIFIER
PXA300.4
Ownerā€™s Manual | English
Manual del Propietario | EspaƱol
AMPLIFICADOR DEL LA SERIE PXA.4
Benutzerhandbuch | Deutsch
MONOVERSTƄRKER DER PXA.4-SERIE
Manuel dā€™utilisation | FranƧaise
AMPLIFICATEUR DE SƉRIE PXA.4
PXA Ampliļ¬ers


Product specificaties

Merk: Kicker
Categorie: Hifi systeem
Model: 46HDR154

Heb je hulp nodig?

Als je hulp nodig hebt met Kicker 46HDR154 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Hifi systeem Kicker

Handleiding Hifi systeem

Nieuwste handleidingen voor Hifi systeem