Kenwood KNA-SPM100 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Kenwood KNA-SPM100 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
KNA-SPM100
Speed Pulse Generator for KENWOOD Wireless Apple CarPlay Ready Receivers
KNA-SPM100 OBD-II Speed Pulse Generator
The KNA-SPM100 provides a simplified method for obtaining a vehicle’s speed pulse
information. It requests a vehicle’s speed using OBD-II and then generates a speed pulse
to be provided to the receiver.
Compatible with most vehicles 2008 - Present
Pre-programmed to work once installed
Small footprint for easy installation
Simple 3-wire hookup and OBD-II connection cable
Red Wire - Connect to 12V Switched
Power
Black Wire - Connect to Ground
Purple/ Wire - Connect to
Receiver’s Speed Sense WirePink
OBD-II Plug - Connect to Vehicle’s
OBD-II Plug
Molex Plugs - Connect all to
KNA-SPM100 Interface
1. Power Receiver On.
2. The KNA-SPM100 interface LED will
blink 2 times, then OFF. RED
3. The KNA-SPM100 has successfully
programmed and is ready for use.
Connections Installation Instructions
If the KNA-SPM100 interface
did not blink 2 times, then RED
OFF, please refer to page 2.
White
KNA-SPM100
FAQ & Troubleshooting
LED Diagnostics FAQ
Receiver Messages
LED Blinks IndenitelyRED
» KNA-SPM100 did not receive a
response from the vehicle.
- This means that the KNA-SPM100
is not compatible with that vehicle.
»CAN wires are disconnected.
- Verify CAN wire connections.
How can I verify if a vehicle is compatible?
» Verify that the vehicle’s year of
production is 2008+ and has an OBD-II plug.
»The KNA-SPM100 will not work If the
vehicle doesn’t allow a scan tool to be
plugged into it while the vehicle is turned
on and/or while driving. Vehicle’s that
may exhibit this symptom typically include
high-end European models.
»Ultimately, the only other way to verify if
the KNA-SPM100 is compatible is to connect
it to a vehicle and verify the LED sequence.
LED Blinks / During that RED GREEN
Ignition Cycle
»KNA-SPM100 has detected another
OBD-II device, MRR, or another
radio replacement interface module
communicating on the bus.
- The KNA-SPM100 cannot be
used in conjunction with another OBD-II
device or MRR (please refer to the MRR or
radio replacement interface instructions
for vehicle speed pulse connection).
If you are still receiving a message like
this when attempting to use Wireless
Apple CarPlay while the vehicle is in
motion:
- The receiver is not receiving a proper
and/or any vehicle speed information.
- The GPS antenna is not connected
or an incorrect GPS antenna is being used.


Product specificaties

Merk: Kenwood
Categorie: Niet gecategoriseerd
Model: KNA-SPM100

Heb je hulp nodig?

Als je hulp nodig hebt met Kenwood KNA-SPM100 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Kenwood

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Festo

Festo VPPI Handleiding

21 November 2024
Festo

Festo SFAB Handleiding

21 November 2024
Festo

Festo SFAH Handleiding

21 November 2024
Festo

Festo DRRD-12 Handleiding

21 November 2024
Festo

Festo SDE3 Handleiding

21 November 2024
Festo

Festo SFTE Handleiding

21 November 2024
Festo

Festo CRVZS-5 Handleiding

21 November 2024