Kenwood Excelon CA-PLT14SG3 Handleiding

Kenwood Niet gecategoriseerd Excelon CA-PLT14SG3

Lees hieronder de 📖 handleiding in het Nederlandse voor Kenwood Excelon CA-PLT14SG3 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new product.
© 2023 JVCKENWOOD Corporation
CA-PLT14SG3
AMPLIFIER MOUNTING PLATE DESIGNED AND ENGINEERED FOR
2014-UP HARLEY-DAVIDSON® FLH MOTORCYCLES
INSTRUCTION MANUAL
JVCKENWOOD Corporation
FLH Side Plate Installation Instructions
Installation procedure
1. With your ignition switch in the "OFF" position, remove your outer fairing/headlamp
assembly and set it aside. Refer to a service manual if you need help with this.
NOTE: Placing a towel on the front fender can help prevent scratches or "dings" from
dropped tools or fasteners, etc.
2. Clutch Side Speaker Cabinet Removal: The images below show the 8 fasteners that
will need to be removed to allow the clutch side cabinet to be removed from the bike.
If your bike has the CB module, (mounted "sideways" on the clutch side cabinet), undo
the antenna cable and main harness. The CB module will stay attached to the clutch side
cabinet when removed. Undo the speaker wire plugs going into the cabinet (pink & pink
with black stripe wires). If your bike had the CB Module, remove its mounting plate from
the speaker cabinet.
3. Attaching the Main Plate to the Speaker Cabinet: On the side of the cabinet, you will
see a threaded insert and a locating post as seen in Fig 1.3. Put the main plate on the
cabinet so one of the holes in the plate goes over the locating post, and the other sits
over the threaded insert. If you removed a CB module from an Ultra, you can use the
screw that secured that module to the speaker pod. If your bike did not have a CB module,
use the machine screw that came in the kit to secure the side plate to the speaker cabinet.
Fig 1.3 on the next page shows the plate correctly placed on the speaker cabinet.
Figure 1.1 - Side View of Cabinet Figure 1.2 - Back View of Cabinet
Note: Brake Side Shown, But Fastener
Location is the Same for Clutch Side
2
FLH Side Plate Installation Instructions - Cont.
4. Preparing the Plate for the Amp: The kit comes with self-adhesive "hook and loop"
material. Separate this so you have 2 pieces. If your amplier does not already have hook
and loop material applied, one of the pieces will be applied to the underside of the amp.
Making sure you use the opposite material to what is on the underside of the amp (refer
to Fig 1.3). cut the remaining piece of hook and loop material so you have 2 smaller pieces
close to the size of the metal areas highlighted by white rectangles. Apply the pieces just
cut to the correct sections on the plate.
5. Attaching the Amplier to the Plate: If you are installing a KENWOOD XM160-2, the amp
will "stick" to the plate as shown (see the white circle in Fig 1.4). The "top" and left "end" of
the amp must be ush to the "top" and left "end" of the plate or the amp will not t.
NOTE: It is CRITICAL that the "amplied pigtail" of the amp be on the speaker side of the
cabinet as shown in Fig 1.4. In the kit is a 14" long "zip tie" which will wrap around the
plate and around the amp. Tighten the "zip tie" so it’s snug only. The zip tie is on there as a
backup in the unlikely event the hook and loop adhesive fails.
6. Placing the Amp and Cabinet into the Bike: As shown in Fig 1.4, the "amplied pigtail"
on the amp needs to be positioned over the top of the amp. If you do not do this
now, you will not have access to this plug when wiring the amp. The cabinet/amplier
assembly will now go in the bike as one unit. Some "nesse" will need to be shown, but
this will go without forcing anything. With the cabinet assembly in place, reinstall all 8
fasteners and secure the speaker cabinet to the bike and then proceed with wiring the
amplier.
Figure 1.3 - Plate Correctly Placed Figure 1.4 - Amp Correctly Placed
3

Product specificaties

Merk: Kenwood
Categorie: Niet gecategoriseerd
Model: Excelon CA-PLT14SG3

Heb je hulp nodig?

Als je hulp nodig hebt met Kenwood Excelon CA-PLT14SG3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Kenwood

Kenwood

Kenwood UBZ-LJ9 Handleiding

16 Juli 2024
Kenwood

Kenwood CA-DR1130 Handleiding

10 Juli 2024
Kenwood

Kenwood LS-600BT Handleiding

19 Maart 2024
Kenwood

Kenwood Excelon CA-POD14AC Handleiding

15 Augustus 2023
Kenwood

Kenwood Excelon CA-GRL98RG Handleiding

15 Augustus 2023
Kenwood

Kenwood Excelon CA-PLT98 Handleiding

15 Augustus 2023
Kenwood

Kenwood Excelon CA-PLT14SG Handleiding

15 Augustus 2023
Kenwood

Kenwood Excelon CA-PLT14RG Handleiding

15 Augustus 2023
Kenwood

Kenwood Excelon P-HD4UT Handleiding

15 Augustus 2023
Kenwood

Kenwood Excelon CA-GRL14RG Handleiding

15 Augustus 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Festo

Festo VPPI Handleiding

21 November 2024
Festo

Festo VAVE-P17-TP-5YL1-P Handleiding

21 November 2024
Festo

Festo SD-SUB-D-BU9 Handleiding

21 November 2024
Festo

Festo SAMH-F12-MK Handleiding

21 November 2024
Festo

Festo SFAB Handleiding

21 November 2024
Festo

Festo SFAH Handleiding

21 November 2024
Festo

Festo DRRD-12 Handleiding

21 November 2024
Festo

Festo SDE3 Handleiding

21 November 2024
Festo

Festo SFTE Handleiding

21 November 2024
Festo

Festo CRVZS-5 Handleiding

21 November 2024