Kenwood Excelon CA-PLT14SG Handleiding

Kenwood Niet gecategoriseerd Excelon CA-PLT14SG

Lees hieronder de 📖 handleiding in het Nederlandse voor Kenwood Excelon CA-PLT14SG (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 120 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new product.
© 2023 JVCKENWOOD Corporation
CA-PLT14SG
AMPLIFIER MOUNTING PLATE DESIGNED AND ENGINEERED FOR
2014-UP HARLEY-DAVIDSON® STREET GLIDE®, ULTRA, OR ULTRA TRIKE
MOTORCYCLES
INSTRUCTION MANUAL
JVCKENWOOD Corporation
Important Notes
©2023 JVCKENWOOD Corporation. All Rights Reserved. KENWOOD® and eXcelon®
are registered trademarks of JVCKENWOOD Corporation. Harley-Davidson®, Electra
Glide®, Road Glide®, Street Glide®, Ultra Classic®, Tri Glide®, CVO™, Screamin Eagle®
and Tour-Paare trademarks or registered trademarks of Harley-Davidson, Inc. and/
or its affiliates and if used or implied are for reference only. There is no affiliation
between Harley-Davidson, Inc. and/or its aliates and JVCKENWOOD Corporation
and/or its aliates. All other trademarks are the property of their respective owners.
Specications subject to change without notice.
The CA-PLT14SG plate is made to mount ampliers
with a maximum dimension of 8.5” W x 7” D x 2” H
(216mm x 178mm x 51mm).
Installation procedure
1. Over the top of the radio, pull up to release each wire harness from the black plate
via the factory “Christmas tree fasteners. If your bike has factory GPS, the small square
antenna will need to be relocated just behind the voltmeter as shown in Fig 1.1 below.
Figure 1.1 - The white circle shows the new location for the GPS Antenna if your bike
came factory equipped with this feature.
2. Remove the four factory T-20 “Torx screws that go through the top of the black plate
and into the top of the radio. Set these screws aside for now.
3. Sit the main amplier plate over the top of the radio, noting the 4 holes in the plate will
line up with the 4 holes left by the factory screws just removed. The factory screws will
now go through the main mounting plate, through the black plate over the top of the
radio, and into the top of the radio.
4. Locate the Velcro® that came in the box and stick it to the bottom plate of the amp
being installed. You can now stick the amp to the mounting plate just installed.
Depending on the amp you are installing, you can use the “tabs on the CA-PLT14SG to
re-secure the wire harnesses that were held in place using the Christmas Tree Fasteners.
For updated information (the latest Instruction Manual, etc.),
please visit the following website:
https://manual.kenwood.com/en_contents/search/


Product specificaties

Merk: Kenwood
Categorie: Niet gecategoriseerd
Model: Excelon CA-PLT14SG

Heb je hulp nodig?

Als je hulp nodig hebt met Kenwood Excelon CA-PLT14SG stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Kenwood

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Festo

Festo VPPI Handleiding

21 November 2024
Festo

Festo SFAB Handleiding

21 November 2024
Festo

Festo SFAH Handleiding

21 November 2024
Festo

Festo DRRD-12 Handleiding

21 November 2024
Festo

Festo SDE3 Handleiding

21 November 2024
Festo

Festo SFTE Handleiding

21 November 2024
Festo

Festo CRVZS-5 Handleiding

21 November 2024