Kenwood Excelon CA-LID98 Handleiding

Kenwood Niet gecategoriseerd Excelon CA-LID98

Lees hieronder de 📖 handleiding in het Nederlandse voor Kenwood Excelon CA-LID98 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new product.
© 2023 JVCKENWOOD Corporation
CA-LID98
REPLACEMENT 6” X 9” SADDLEBAG LIDS DESIGNED AND
ENGINEERED FOR 1998-2013 HARLEY-DAVIDSON® MOTORCYCLES
WITH FACTORY-STYLE HARD SADDLEBAGS
INSTRUCTION MANUAL
JVCKENWOOD Corporation
Safety precautions
WARNING
Contents
Section 1: Bag and Lid Prep.................................................3
Section 2: Disassembling The Factory Lid........................3
Section 3: Preparing The New Lid......................................4
Section 4: Mounting The Speakers....................................5
Section 5: Routing The Wires In The Saddlebag.............6
Section 6: Routing The Speaker Wire Harness................6
Section 7: Wiring The Lids To The Amplifier....................7
The factory saddlebag hinges limit the size of the speaker
magnet that can be used and allow the lids to open and close
without issue. KENWOOD assumes ZERO RESPONSIBILITY for
tment issues, or water leaks when any speaker brand other than
KENWOOD is used. Be sure of all clearances and inspect the parts
carefully BEFORE painting.
Do Not Use “Thread Lock” or “Screw Glue” of any kind, as it
destroys plastic and will cause part failure.
Most speaker magnets are large and powerful. Credit cards
and electronics can be sensitive to magnets, so please exercise
caution in how you pack your saddlebags. Metal objects packed
into your bags may end up stuck to the magnet, so please use
caution when opening the lids. Magnets can also get hot when
speakers are being played, especially at higher volumes. Please
consider this when packing your saddlebags.
2
3. The supplied grommet in Fig 1.2 is split to make
the installation easier once the wire is in the bag. The
white circle in the picture shows a “plug that can easily
be removed. If the only wire you have going into your
saddlebag is the speaker wire, leave the plug in place. If
you have a second wire for such things as lighting etc.,
removing the plug from the grommet will allow the
second wire to also pass through without having to drill
additional holes in your saddlebag. Figure 1.2
Figure 1.3
Figure 1.1
3
Section 1 - Bag and Lid Prep
Section 2 - Disassembling The Factory Lid
Installation procedure
1. Start by removing the 2 screws on the underside of the lid that secures the grille in
place. Lift up slightly on the grille and slide out. Remove the saddlebag from the bike and
put it on a stable working surface (placing blankets, towels, etc. on your work surface will
help to protect the paint).
2. The white circle in Fig 1.1 is where a 3/4”
(19mm) hole will need to be drilled. This
hole is where the supplied rubber grommet
will go to allow the lid’s speaker wire to pass
through from the saddlebag. Use masking
tape over the painted area to be drilled and
start with a small bit, gradually working your
way up to the 3/4” (19mm) hole. Drilling the
hole with the lid still on is recommended.
NOTE: As you disassemble your factory lid, make note of what screws came from where, as
they will be re-used.
1 . R e m o v e t h e 4
scr ews highlighted
with white arrows in
Fig 1.3 that hold the
cloth tether in place.
With the tether off,
slide one of the metal
bars out from inside
the tether, as it will be
used for the new lid.


Product specificaties

Merk: Kenwood
Categorie: Niet gecategoriseerd
Model: Excelon CA-LID98

Heb je hulp nodig?

Als je hulp nodig hebt met Kenwood Excelon CA-LID98 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Kenwood

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd