Kenwood Excelon CA-HRN14UT Handleiding

Kenwood Niet gecategoriseerd Excelon CA-HRN14UT

Lees hieronder de 📖 handleiding in het Nederlandse voor Kenwood Excelon CA-HRN14UT (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 136 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new product.
© 2023 JVCKENWOOD Corporation
CA-HRN14UT
REAR SPEAKER HARNESS DESIGNED AND ENGINEERED
FOR 2014-UP HARLEY-DAVIDSON® ULTRA MOTORCYCLES
INSTRUCTION MANUAL
JVCKENWOOD Corporation
Important Notes
©2023 JVCKENWOOD Corporation. All Rights Reserved. KENWOOD® and eXcelon®
are registered trademarks of JVCKENWOOD Corporation. Harley-Davidson®, Electra
Glide®, Road Glide®, Street Glide®, Ultra Classic®, Tri Glide®, CVO™, Screamin Eagle®
and Tour-Paare trademarks or registered trademarks of Harley-Davidson, Inc. and/
or its affiliates and if used or implied are for reference only. There is no affiliation
between Harley-Davidson, Inc. and/or its aliates and JVCKENWOOD Corporation
and/or its aliates. All other trademarks are the property of their respective owners.
Specications subject to change without notice.
Rear Speaker Harness Installation Instructions
Installation procedure
1. You will see that one end of this harness has two 4-pin connectors. One of these white
4-pin plugs will plug into the amplied out” on the amp that will power the rear speakers.
The amplifier comes with a short harness with a black 8-pin plug and two 4-pin blue
plugs. Plug the 8-pin black plug into the ampliers input that will power the rear speakers.
The second 4-pin plug marked “rear in” on the rear speaker harness will plug into one of
the blue 4-pin connectors, noting they will only go in one way.
2. The harness that will run the rear speakers will pass under the inner fairing on the clutch
side of the bike. Loosen the tank’s chrome console” and run the wires up and over the gas
tank, but under the tanks chrome console. There is a provision on the front of the console
for wires to pass under it allowing the power harness to run on the brake side of the ller
spout and the rear speaker harness to run on the clutch side of the spout.
NOTE: Although not necessary, the power and rear harnesses can go under the gas tank if
you choose to remove and re-install the tank. With the tank removed you will see a factory
wire channel where wires pass along the bike’s frame. Removing the top of the channel
will allow for the power and rear speaker harness to be safely run under the tank to the
battery area. When reinstalling the top of the channel take care not to pinch any wires
along the edges of the channel.
3. Just behind the threaded insert that holds the seat bolt on the back fender, you will see
a large factory wire plug. One side of the plug has wires that go to each rear speaker pod.
Separate this large factory plug. One plug from the KENWOOD rear harness will plug into
each side of the factory plug just separated. They will only go together one way.
For updated information (the latest Instruction Manual, etc.),
please visit the following website:
https://manual.kenwood.com/en_contents/search/


Product specificaties

Merk: Kenwood
Categorie: Niet gecategoriseerd
Model: Excelon CA-HRN14UT

Heb je hulp nodig?

Als je hulp nodig hebt met Kenwood Excelon CA-HRN14UT stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Kenwood

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Festo

Festo VPPI Handleiding

21 November 2024
Festo

Festo SFAB Handleiding

21 November 2024
Festo

Festo SFAH Handleiding

21 November 2024
Festo

Festo DRRD-12 Handleiding

21 November 2024
Festo

Festo SDE3 Handleiding

21 November 2024
Festo

Festo SFTE Handleiding

21 November 2024
Festo

Festo CRVZS-5 Handleiding

21 November 2024