Kanto YU Passive Handleiding

Kanto Speaker YU Passive

Lees hieronder de 📖 handleiding in het Nederlandse voor Kanto YU Passive (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Supporting your digital lifestyle
English
User Manual
YU Passive Speakers
Thank you for choosing YU Passive speakers, designed by Kanto in Canada. We recommend you
read these instructions carefully before using the speakers, and keep them for future reference.
Kanto cannot be liable for damage or injury caused by incorrect setup or use of this product.
These speakers were carefully tested and inspected during production, and before packaging
and shipping. After unpacking, please check for any damage. It is rare that a unit is damaged
during shipping, but if this happens contact your retailer immediately. You can also call Kanto
directly at 1-888-848-2643 or email support@kantoliving.com.
Introduction
What's in the Box?
YU Passive
Speakers
User
Manual
x8
Self-Adhesive
Rubber Feet
x2
2
We recommend the Kanto SP26PL and SP32PL oor stands for both the YU Passive 4" and YU Passive
5.25". For desktop use, we recommend the S4 and SP9 desktop stands for YU Passive 4", and the S6 and
SP6HD desktop stands for YU Passive 5.25".
The space between the two speakers and the distance from the listener is important. If the speakers are
positioned too close or too far apart, stereo imaging will not be fully developed.
YU Passive is designed to perform optimally positioned at least 8” from the rear wall in an average
listening room. However, it may not be possible to install the speakers in this position and since rooms
vary in shape, size, and furnishing, a certain amount of experimentation is necessary to determine the
most suitable position.
Moving the speakers very close to the rear wall will enhance the bass frequencies but will tend to reduce
soundstage depth, while moving the speakers away from the rear wall will tend to have the opposite
eect. Avoid positioning the speakers close to or in the corners of the room, as this will excite undesirable
room coupling in the low and middle frequencies. If the width of the rear wall is limited then toe-in the
speakers slightly to reduce reections. Room characteristics and positioning have a profound eect on
the performance of the speakers, so time and eort devoted to achieving the optimum positions will be
rewarded.
Setting Up Your Speakers
YU Passive 4" is rated to 70 W at 4 ohms, YU Passive 5.25" is rated to 100 W at 6 ohms.
Repeat the above procedure for connecting the remaining speaker to the RIGHT amplier channel. Make
sure that no bare wires from any of the connections touch other teminals as this could cause a short and
damage your equipment.
Conventional Connection
Amplier Requirements
Using 16-12 gauge speaker wire, connect the RED "positive" (+) terminal of one speaker to the RED
"positive" (+) terminal of your amplier's LEFT channel. Connect the BLACK "negative" (-) terminal of the
speaker to the BLACK "negative" (-) teminal of your amplier's LEFT channel.
Attention
When connecting audio cables the amplier must be turned OFF. After connecting all cables, the unit can be turned . ON
5.25”
YUP 6
100 W
6 Ω
4”
YUP4
70 W
4 Ω
3
Specications
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
Important Safety Precautions
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE BACK
PANEL. NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Read these instructions.
Follow all instructions.
Keep these instructions.
Clean only with a dry cloth.
Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including
ampliers) that produce heat.
Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been
damaged in any way, such as liquid has been spilled or objects have fallen into the aparatus, the aparatus
has been exposed to rain or moisture, the apparatus does not operate normally, or the aparatus has been
dropped.
Tweeters 1 inch Silk Dome
Woofers 4 inch Kevlar®
Power Handling 70 W Per Speaker
Impedance 4 ohm
Sensitivity 86 db (2.83 V/1m)
Frequency Response 60 Hz - 20 kHz
Speaker Terminals Knurled Binding Post
Bottom Mounting Hole 1/4"-20
Dimensions
Dimensions (each speaker) 5.5” W x 7.5” D x 8.7” H
(14 x 19 x 22 cm)
Net Weight (each speaker ) 5.5 lb (2.5 kg)
Gross Weight (boxed pair) 14.6 lb (6.6 kg)
Shipping Box Dimensions 11.3” W x 16.7” D x 13.2” H
(28.7 x 42.5 x 33.5 cm)
YU Passive 4"
Tweeters 1 inch Silk Dome
Woofers 5.25 inch Kevlar®
Power Handling 100 W Per Speaker
Impedance 6 ohm
Sensitivity 89 db (2.83 V/1m)
Frequency Response 50 Hz - 20 kHz
Speaker Terminals Knurled Binding Post
Bottom Mounting Hole 1/4"-20
Dimensions
Dimensions (each speaker) 6.9” W x 8.1” D x 10.7” H
(17.5 x 20.5 x 27.2 cm)
Net Weight (each speaker ) 8.7 lb (4 kg)
Gross Weight (boxed pair) 22 lb (10 kg)
Shipping Box Dimensions 12” W x 19.5” D x 15.4” H
(30.5 x 49.5 x 39 cm)
YU Passive 5.25"


Product specificaties

Merk: Kanto
Categorie: Speaker
Model: YU Passive

Heb je hulp nodig?

Als je hulp nodig hebt met Kanto YU Passive stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker Kanto

Kanto

Kanto ORA4 Handleiding

11 November 2024
Kanto

Kanto ORA Handleiding

7 December 2023
Kanto

Kanto YU6 Handleiding

1 Juli 2023
Kanto

Kanto SYD Handleiding

28 Juni 2023
Kanto

Kanto YU Handleiding

26 Juni 2023
Kanto

Kanto YU2 Handleiding

26 Juni 2023
Kanto

Kanto TUK Handleiding

13 Juni 2023
Kanto

Kanto YU4 Handleiding

13 Juni 2023
Kanto

Kanto YUP4 Handleiding

13 Juni 2023

Handleiding Speaker

Nieuwste handleidingen voor Speaker