JVC XL-PV400 Handleiding

JVC CD-spelers/recorder XL-PV400

Lees hieronder de 📖 handleiding in het Nederlandse voor JVC XL-PV400 (4 pagina's) in de categorie CD-spelers/recorder. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Remove the rechargeable batteries from their case before use.

Use numbers indicated in parentheses when asking for replacement parts.

AC adaptor (RFEA 417C) ............................................................................................................... 1 pc.

Stereo headphone ............................................................................................................................ 1 pc.

Car adaptor (CA-R455) (XL-PV400) ............................................................................................ 1 pc.

Car audio cassette adaptor (CA-RC4/CA-RC5) (XL-PV400) ................................................. 1 pc.

Wired remote control (XL-PG5) ................................................................................................... 1 pc.

Rechargeable Ni-Cd batteries (BN-R122J) with carrying case pcs.(XL-PG5) ........................... 2

Supplied Accessories

Check the packing carton for these accessories.

Concerning Compact Discs

VICTOR COMPANY OF JAPAN, LIMITED

Precautions

Before using this unit, be sure to read the applicable items of the

operating instructions and these safety-suggestions carefully.

Afterwards keep them handy for future reference. Take special

care to follow the warnings indicated on the unit itself as well as

in the operating instructions.

Safety

1. Care of AC adaptor - Take care that the cord of the AC adap-

tor should be routed so that they are not likely to be walked on

or pinched by items placed upon or against them. Never take

hold of the AC adaptor if your hand is wet, and always grasp

the plug body when connecting or disconnecting it.

2. Nonuse Periods - When not in use, be sure to disconnect the

AC adaptor from the AC power outlet.

3. Batteries - If the set is not used for a long period of time or is

used only from an AC power source, remove all the batteries to

prevent potential damage due to possible battery leakage. Do

not mix batteries (old and new ) or different types of batteries.

Installation

■ Environment

1.Condensation - Moisture may form on the lens in the follow-

ing conditions…

• immediately after a heater has been turned on.

• in a steamy or very humid room.

• when the unit is suddenly moved from a cold environment

to a warm one. If moisture forms inside this unit, it may not

operate properly. To correct this problem wait about one

hour for the moisture to evaporate.

■ Placement

1.Foreign Material - Care should be taken so that objects do not

fall into and liquids are not spilled into the unit. Do not subject

this unit to excessive smoke, dust, mechanical vibration, or

shock.

2.Magnetism - The unit should be situated away from equip-

ment or devices that generate strong magnetic fields.

3. Stacking - Do not place any objects, on top of the unit.

Maintenance

(See page 5 for details.)

Clean the cabinet, panel and controls with a soft cloth lightly

moistened with mild detergent solution.

Do not use any type of abrasive pad, scouring powder or solvent

such as alcohol or benzine.

Service

1.Damege Requiring Service - The unit should be serviced by

qualified service personnel when:

(a) The AC adaptor is damaged; or

(b) Objects have fallen or liquid has been spilled into the unit; or

(d) The unit does not appear to operate normally or exhibits a

marked change in performance; or

(e) The unit has been dropped, or the enclosure damaged.

THE FOLLOWING PHRASES ARE APPLIED ONLY FOR

U.S.A.:

CAUTION!

THIS PRODUCT UTILIZES A LASER.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE

OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN

MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.

REFER SERVICING TO QUALIFIED PERSONNEL.

CAUTION!

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules.

These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio fre-

quency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to ra-

dio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or tele-

vision reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to cor-

rect the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and re-

ceiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

Any unauthorized changes or modifications to this equip-

ment would void the user’s authority to operate this device.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions : (1)

This device may not cause harmful interference, and (2) this

device must accept any interference received, including in-

terference that may cause undesired operation.

MUST BE RECYCLED OR DISPOSED OF PROPERLY.

ATTENTION:

The product that you have purchased is powered by a re-

chargeable battery. The battery is recyclable. At the end of

it’s useful life, under various state and local laws, it may be

illegal to dispose of this battery into the municipal waste

stream.

Check with your local solid waste officials for details in

your area for recycling options or proper disposal.

RBRC

Ni-Cd

Printed in Japan

0199IMMCREPAN

PORTABLE CD PLAYER XL-PG4/XL-PG5/

XL-PV400

INSTRUCTIONS

Thank you for purchasing this JVC product. Please read these instructions carefully before starting

operation to be sure to obtain optimum performance and a longer service life from the unit.

Only compact discs bearing this mark can be used with this unit.

However, continued use of irregular shape CDs (heart-shape, octagonal, etc.) can damage

the unit.

If moisture has formed on a disc

When moisture has formed because the

disc was brought suddenly into a warm

room from a cold environment, wipe it off

using a soft dry cloth.

When storing discs

Avoid locations which are

• Exposed to direct sunlight.

• Susceptible to high levels of humidity or

dust.

• Directly exposed to heat from a heating

appliance.

• On top of a car dashboard or near the

rear window.

Handling precautions

• On the label side (the side with writing)

Do not write anything using a pencil,

ball-point pen, etc. Do not stick on paper

or labels.

• On the disc (shiny) side

Handle this side carefully to keep it free

from fingerprints or scratches. Do not

use record cleaners, solvents, etc.

• Do not attach labels or stickers to CDs.

Do not use CDs with exposed adhesive

from tape or left over peeled off stickers.

• Do not use scratch-proof protectors or

covers other than those specified for use

with this unit.

If the surface is dirty

Wipe it with a damp cloth and then wipe dry.

Wipe from the center toward the outer circumference.

How to hold a disc

How to store the disc in

its case

How to remove a disc from its case

Label side up

Play surface (shiny surface)

LVT0231-001A [J]

RQT4851-P

For Customer Use:

Enter below the Model No. and Serial

No. which are located either on the rear,

bottom or side of the cabinet. Retain this

information for future reference.

Model No.

Serial No.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

Fast forward/

reverse

To adjust the

volume

To start play

To stop play

To turn off the

unit

HOLD

Connect the car audio cassette adaptor to the unit’s

headphone jack. (When doing this, keep the unit’s

VOLUME control at a setting between 4 and 6.)

Using the unit with a car audio

system

XL-PV400 comes with the car adaptor and car audio cassette

adaptor.

• Car adaptor (CA-R455)

• Car audio cassette adaptor (CA-RC4/CA-RC5)

For connection to the car audio system:

If there is an Aux jack in the car audio system, connect the OUT

jack of the CD player with the Aux jack using a 3.5 mm diameter

stereo mini-plug signal cord (optional).

Depending on the automobile used, noise may occur, and in that case,

it is recommended that a KS-U32 noise filter (optional) be used.

It may not be possible to use the unit with some types of car ste-

reo owing to restrictions imposed by the construction of the car

audio cassette adaptor.

For further details, refer to the instructions of the part concerned.

Maintaining the unit

Wipe the unit with a soft cloth. Remove stubborn dirt using a

cloth which has been dipped in water or soapy water and wrung

out, and then wipe dry.

• If you intend to use a chemically treated cleaning cloth, read its

directions first.

• Do not use alcohol or paint thinners.

Maintaining the lens

Open the lid and clean the lens as shown in the figure.

Use a cotton swab to gently wipe off any finger-prints.

Recommended product:␣ Lens cleaner kit

Using the unit with an audio system

Using a stereo connection cable (not included), you can listen to

CDs through your audio system.

• Connect the cable to the amplifier after turning off its power.

• Do not connect the cable to the PHONO jacks on the amplifier.

• Obtain the optional connecting cable if the amplifier comes

with mini-phone jacks.

• Adjust the volume level on the amplifier.

CD/AUX

OUT jack

Back panel of the unit

Amplifier

(White)

(Red)

Sound quality changes when HBS is selected, but volume is re-

duced by approximately fifty percent.

The remote control can be operated regardless of the hold mode

of the unit.

Preparation:

Release the remote control from the hold mode.

■ Operation confirmation tones

When an operation button is pressed, a confirmation tone

sounds. Refer to the parentheses in the illustration for the differ-

ent types of confirmation tones.

How to use the wired remote control

Reverse

(Beep Beep Beep)

Forward

(Beep Beep)

Skip function

Press once during play.

Search function

Keep depressed during play.

When adjusting the volume using the

remote control, position the volume

control on the unit between 4 and 6.

Press once during off or stop mode.

Press once during play.

Keep depressed during play or stop

mode.

(Beep Bee p)... ...

(Beep)

(Beep Beep)...

Using the Unit with Optional Accessories Maintenance

Using the Wired Remote Control

Air blower for

camera lens

Lens

Stereo connection cable (not included)

Note:

XL-PG5 ONLY

Accidental Operation Prevention Function (Hold Mode)

This function causes the unit to ignore short, accidental button

presses.

The misoperation prevention function pre-

vents the following:

• Powering on the unit accidentally (which can cause the batter-

ies to go dead).

• Play being cut off unexpectedly in the middle of a selection.

The unit and wired remote control have HOLD switches, each of

which works independently.

To use the accidental operation prevention

function

• To prevent the unit from powering up accidentally, set the

HOLD switch to the HOLD position.

• To prevent the unit from unexpected operation during play,

set the HOLD switch to the HOLD position after playing the

disc.

OPEN button operation

Even when the unit is in hold mode, the (CD) lid can be opened

or closed by pressing the OPEN button.

“ ” indication

When the unit is in hold mode, pressing any operation button

(other than the OPEN button) causes the indication “ ” to

appear on the display.

When the unit is powered off

The “ ” indication appears only when the button is3 8

pressed.

To release the function

Move back the HOLD switch.

XL-PG5

Only

Hold Mode

HOLD

Note:

• Recharging already charged batteries will shorten their service

life.

• When recharging batteries for the first time or when they have

not been used for a long period of time, the play time may be

shorter than usual. In a case like this, repeatedly recharge and

discharge the batteries. This will restore them to their regular

state.

• Do not allow any metal objects to touch the terminals of re-

chargeable batteries since this may cause short-circuiting

which is dangerous.

• Do not peel off the plastic covering on the rechargeable batter-

ies. Short-circuiting may occur which is dangerous.

Dry cell batteries / rechargeable

batteries

To prevent damage to the batteries and electrolyte leakage, heed

the following points.

• Align the and polarities properly when inserting the bat-, .

teries.

• Do not mix different types or makers of batteries or old and

new batteries.

• Remove the batteries if you do not plan to use the unit for a

long period of time.

• Do not throw batteries into a fire, and do not short-circuit, dis-

assemble or subject them to excessive heat.

• Do not attempt to recharge dry cell batteries.

Carrying dry cell batteries /

rechargeable batteries around

When putting dry cell or rechargeable batteries in a pocket or

bag, ensure that no other metal objects such as a necklace are

placed together with them. Contact with metal may cause short-

circuiting which, in turn, may cause a fire.

Be absolutely sure to carry the rechargeable batteries in the bat-

tery carrying case.

Listening caution

Do not play your headphones or earphones at a high volume.

Hearing experts advise against continuous extended play.

If you experience a ringing in your ears, reduce volume or dis-

continue use.

Do not use while operating a motorized vehicle. It may create a

traffic hazard and is illegal in many areas.

You should use extreme caution or temporarily discontinue use

in potentially hazardous situations.

Even if your headphones or earphones is an open-air type de-

signed to let you hear outside sounds, don’t turn up the volume

so high that you can’t hear what’s around you.

Sound can be deceiving. Over time your hearing “comfort level”

adapts to higher volumes of sound. So what sounds “normal”

can actually be loud and harmful to your hearing.

Guard against this by setting your equipment at a safe level BE-

FORE your hearing adapts.

To establish a safe level:

• Start your volume control at a low setting.

• Slowly increase the sound until you can hear it comfortably

and clearly, and without distortion.

Once you have established a comfortable sound level:

• Set the dial and leave it there.

Rechargeable batteries

• Only the BN-R122J battery can be recharged.

• If the power delivered by the batteries lasts for a very short

time after recharging, it means that the batteries’ service life is

over. Do not use them any more.

When purchasing rechargeable

batteries

As a safety precaution, the portable CD players made by JVC

have a construction designed to make it impossible to recharge

ordinary batteries.

To use rechargeable batteries, be absolutely sure to purchase the

rechargeable Ni-Cd batteries designed especially for this unit.

Special rechargeable Ni-Cd batteries:

BN-R122J (set of 2)

For details, check with your dealer.

When driving a car

In the interest of traffic safety, do not operate the unit while driv-

ing.

INFORMATION (For Canada)

This digital apparatus does not exceed the Class B limits for

radio noise emissions from digital apparatus as set out in the

interference-causing equipment standard entitled “Digital

Apparatus”, ICES-003 of the Department of Communications.

Special rechargeable

batteries

Ordinary dry cell

batteries/rechargeable

batteries

Check this

Is the disc properly secured in place?

• Is the unit in HOLD status?

• Is the disc properly secured in place?

• Is there moisture condensation on the lens?

(Wait for about an hour and then try again.)

Did you press the PUSH button to release the disc?

Is the RESUME, NORMAL, RANDOM (play mode) selector

in the NORMAL position?

• Is the headphone plug inserted all the way?

• Is the plug dirty? (Wipe away dirt on the plug.)

Are you using the unit body too near a TV or tuner? (If the

TV or tuner is connected to a simple indoor antenna,

connect it to an outdoor antenna.)

Problem

Cannot close cover.

Cannot play discs.

Cannot remove disc.

Tracks on disc do not play

in order, starting with the

first track.

Cannot hear music—too

noisy.

TV picture is distorted.

Radio reception is noisy.

Portable CD player

Type : Compact disc player

Signal detection system : Non-contact optical pickup (semiconductor laser)

Pickup system : 3 beam laser

Number of channels: : 2 channels (stereo)

Frequency response : 20 Hz to 20,000 Hz

Wow & flutter : Unmeasurable

Output : Headphone (3.5 mm dia. stereo 1)×

9 mW/ch at 10 % THD/16 ohms matching impedance (16 ohms to 1 kohm)

Out (3.5 mm dia. stereo × 1) 0.6 V/50 kohms

Duration of battery : Approx. 6 hours

(with T.S.P. ON) when using two rechargeable batteries

(BN-R122J or equivalent) charged for 3 hours,

Approx. 21 hours when using two alkaline batteries

(LR6-Panasonic)

Approx. 46 hours when using four alkaline batteries (XL-PG5)

Power requirements : DC 3 V (“AA” size battery 2)×

DC 2.4 V (rechargeable battery 2)×

DC IN 4.5 V

Dimensions (W H D) : 128.5 28.9 144 mm (5-1/16” 1-3/8” 5-21/32”)× × × × × ×

(Excluding buttons and controls)

Mass : Approx. 220 g (0.48 lbs)

(without batteries)

AC adaptor

Input power source : AC 120 V, 60 Hz

Output voltage : DC 4.5 V, 800 mA

* Design and specifications are subject to change without notice.

Specifications Troubleshooting Guide

Before requesting service for this unit, check the chart below for a possible cause of the problem

you are experiencing. Some simple checks or a minor adjustment on your part may eliminate the

problem and restore proper operation.

If you are in doubt about some of the check points, or if the remedies indicated in the chart do not

solve the problem, refer to the directory of Authorized Service Centers (enclosed with this unit) to

locate a convenient service center, or consult your dealer for instructions.

Cautions

•

ES T. 19 24

Mentuke_E(J) 1/26/99, 6:35 PM1

Using rechargeable batteries

Power Supply Preparations

Refer to the specifications (page 6) for information on operating times when using rechargeable batteries or dry-cell batteries.

Using the AC adaptor

Connect the AC adaptor supplied.

Refer to “Using rechargeable batteries” for connection instruc-

tions.

Removing batteries

Push up on the battery in

the direction indicated by

the arrow. Then lift it out.

If the battery lid

compartment

comes loose

Slide the lid back into place

horizontally.

Using the car adaptor

XL-PV400 comes with a car adaptor. For XL-PG4/PG5, obtain the

optional car adaptor as required.

• Car adaptor (CA-R455)

The car adaptor can be used to recharge the unit’s batteries while

in the car.

Using dry-cell batteries

(not included)

After disconnecting the AC adaptor, insert two “AA” (LR6) alka-

line batteries.

The procedure for inserting and removing dry-cell

batteries is identical to that for rechargeable bat-

teries.

Battery indicator

This indicator flashes on and off when the batteries are almost

out of power. Power is cut off completely a short while later.

Rechargeable batteries: Recharge batteries.

Dry-cell batteries: Replace batteries with new ones.

• The length of time the unit will continue to operate after the

battery indicator starts flashing and when the power is cut off

differs depending on the type of batteries used.

• The battery indicator may not flash if rechargeable batteries,

other than those designated by JVC, are used.

3When recharging is complete, unplug the

AC adaptor from the power outlet and the

DC IN jack.

• It takes approximately 3 hours to recharge the rechargeable

batteries.

• Rechargeable batteries have a service life of approximately

300 charge-discharge cycles. If the operating time on one full

charge becomes noticeably shorter than it used to be, the bat-

tery has reached the end of its service life and should be re-

placed.

• Recharging is made only when the unit is powered off. (It is

not possible to recharge the batteries while playing a CD.)

• The AC adaptor and rechargeable batteries may become warm

while recharging is in progress. This in not a malfunction.

Notes:

Make sure to recharge the batteries before using them. The unit

cannot be used to charge rechargeable batteries other than those

specifically designed for it.

XL-PG5 comes with the rechargeable batteries. For XL-PG4/

PV400, obtain the optional batteries as required.

• Rechargeable Ni-Cd batteries (BN-R122J) .......................... 2 pcs.

Recharging procedure

1Insert the special rechargeable batteries

into the unit.

2Connect the AC adaptor.

Note:

The unit is in the standby condition when the AC adaptor is con-

nected. The primary circuit is always “live” as long as the AC

adaptor is connected to an electrical outlet.

If the unit malfunctions or freezes during use,

then disconnect the power sources (the AC

adaptor and batteries).

Re-connect the power source and continue op-

eration.

When recharging starts, the “ ” charging indicator flashes on

and off on the display.

Battery indicator

LVT0231-001A [J]

RQT4851-P

DC IN jack (DC IN 4.5 V )

AC power

outlet

Back panel of the unit

AC-adaptor

Notes:

Using the battery case (XL-PG5 ONLY)

The battery case allows you to extend the maximum playing time

of the unit by loading an additional two LR6 (UM3) alkaline bat-

teries.

• When using the battery case, always insert batteries in the unit

body as well. (The unit cannot be operated on the batteries in

the external battery case alone.)

• Though you can use rechargeable batteries in the battery case,

it does not recharge them. (Use dry cell batteries if possible.)

• When using rechargeable batteries in the unit body, and dry-

cell batteries in the battery case, be sure to use fully charged re-

chargeable batteries and new dry-cell batteries.

• When using four dry-cell batteries, do not mix new and old

batteries.

1 Open the cover of the battery case and in-

sert the batteries.

Insert the end marked (–) first.

2Mount the battery case on the unit body.

Insert the protrusions

on the battery case into

the four indentations in

the unit body.

OPEN

DC IN 4.5V

Notes:

3Secure in place with the screw.

Reverse the above procedure to remove the external battery

case.

For your reference:

The maximum playing time will differ depending on the type of

batteries (rechargeable/dry-cell) loaded in the unit body.

If the cover of the battery case comes loose:

Insert the protrusions into the

holes on either end of the lid.

If the unit malfunctions or freezes during use,

then disconnect the power sources (the AC

adaptor and batteries).

Re-connect the power source and continue op-

eration.

*Recharging will be com-

pleted after 3 hours.

The batteries’ duration

is about 6 hours.

Repeat function

Press REPEAT while disc is playing or when unit is in stop

status.

The setting is switched in the sequence indicated below each time

REPEAT is pressed.

1-track repeat

One track is repeated.

All-track repeat

All the tracks on the

disc are repeated.

Cancel

For your reference:

If REPEAT is pressed during program play, only the tracks in the

programmed sequence are repeated.

(The indication “ALL” is not displayed.)

Changing the sound quality

HBS ON:

Select this setting to boost the low-range response.

OFF:

Select this setting to turn off the HBS function.

Skip play

The disc plays from the specific track through to the last track,

then play stops automatically.

Preparation: Put the unit in stop mode. (See page 3.)

2Select the desired track.

Random play

For your reference:

• It is also possible to press the button while the unit is in¢

stop status to change the first track to be played. (All tracks are

played eventually, regardless of which is played first.)

• Program play is not possible in the random mode.

Resume play

This function allows you to listen from the beginning of the track

where play stopped because the unit was powered off (or

switched to stop status). It is useful when listening to CDs in the

car, etc.

For your reference:

• If the RESUME, NORMAL, RANDOM (play mode) selector is

put in the RESUME position, the all-repeat function will be ac-

tivated automatically as soon as the unit is powered on.

• If power is cut off near the end of a track (power off status),

playback may resume from the beginning of the next track in

some cases.

• If the unit is powered off while a disc was playing and then a

new disc is inserted, play will begin from the middle of the

new disc because the unit remembers the position where play

stopped on the previous disc.

Program play

Up to 24 tracks can be entered in the programmed sequence.

Preparation: Put the unit in stop mode. (See page 3.)

2Select the desired track.

3Register in sequence.

(The indication “M” and the programmed sequence appear

on the display panel.)

4Repeat steps 2 and 3 to program all the

desired tracks.

• If “ ” is displayed

No more tracks may be added to the sequence.

• To confirm the contents of the programmed se-

quence

Press PROGRAM while the disc is playing. (The numbers of

the programmed tracks appear on the display panel in se-

quence.)

• To delete the entire programmed sequence

Press the button.7

For your reference:

It is possible to program the same track in the sequence more

than one.

Release

ALL“ ”

“ ”

Notes:

This function minimizes sound interruption when vibrations are

encountered by utilizing audio data that has been stored ahead

of time (up to the following seconds’ worth).

For XL-PG4/PG5/PV400: approx. 40 seconds

The function starts to store the play data, and the M.RESERVE in-

dicator on the display shows how much data is stored.

ON OFF

T.S.P.

PROGRAM

RESUME RANDOM

NORMAL

RESUME RANDOM

NORMAL

RANDOM

RESUME

RESUME RANDOM

NORMAL

REPEAT

ON OFF

HBS

ON OFF

HBS

RESUME RANDOM

NORMAL

The letters such as in the various illustrations refer to the descriptions in the “Location of Controls” section. (See page 3.)A

Triple Shock Protection (T.S.P.) Function

Using the unit with an audio system

The T.S.P. uses digital signal compression technology. It is rec-

ommended that the T.S.P. be kept in the OFF position if the unit

is connected to a home audio system.

• The position of the T.S.P. switch can be changed during play,

but this may cause a slight interruption in the sound because

the disc’s rotational speed changes.

• During T.S.P. operation, the disc rotates at a higher rate than

usual in order to collect extra audio data. This may cause the

batteries to run out faster and could result in a slight increase

in disc rotation noise.

Unit body status

Stable

Bump encountered

Bumping stops

Bumps continue repeatedly

Play status (audio data status)

Normal (plenty of data is stored)

Normal (stored data is used)

Normal (data again starts to be stored)

Sound is interrupted (data buffer empty)

M.RESERVE indicator

status

Other Play Methods

ButtonOperation

To pause play

To stop play

To turn off the

unit

Fast forward/

reverse

Stop mode

Basic Pla

Portable CD player A

ASkip / search buttons ( , )4 ¢

BDisplay

CPush button (PUSH)

DPlay / pause button (3 8)

EStop / power off button ( )7

FProgram button (PROGRAM)

GRepeat button (REPEAT)

HOpen button (OPEN)

IHeadphones volume control

(VOLUME)

JHBS switch

KHeadphones jack ( )

LPlay mode selector

(RESUME, NORMAL, RANDOM)

MHOLD switch

NTriple shock protection (T.S.P.)

switch

OOut jack (OUT)

Note:

Display/reference

Skip function

Press during play.

Search function

Keep depressed during play.

Following steps 1–6.

In step 4, connect the stereo headphone to the jack. (Plug in firmly.)

• Play stops automatically when all the tracks have been played.

• If the unit has been connected to a car audio system, adjust the volume level between 4 and 6 on the unit, then adjust the volume

level on the system.

PDC in jack (DC IN 4.5 V )

QHole for battery case (XL-PG5

only)

RConnection terminal for battery

case (XL-PG5 only)

Wired remote control

ASkip / search buttons (+, –)

BHOLD switch (HOLD)

CPlay / stop / off button

DPlug

EVolume control (VOL)

Stereo headphone

APlug

For your reference:

“ ” indication

This indication appears for about 30 seconds if the button is3 8

pressed when no disc is loaded in the unit or if the disc is not

completely seated.

“ ” indication

This indication appears when the lid is opened. (However, the

indication does not appear when the unit is powered off.)

Never insert foreign objects into the unit body.

Removing discs

After the disc has stopped rotating, press the PUSH button to re-

lease the disc. (To protect the disc, never open the lid while it is

playing.)

Backlight (XL-PV400 Only)

When using the AC adaptor or the car adaptor, the backlight of

the display turns on.

RESUME RANDOM

NORMAL

HOLD

VOLUME

XL-PG5 only

Track number in play

Release hold mode.

Label must face upward.

Elapsed playing time of each track

Set the play mode

selector to NORMAL.

Close the lid.

XL-PG5

Only

• During program play, these buttons are used to fast

forward or back through the programmed sequence of

tracks.

• During random play, the skip buttons cannot be used

to skip back to tracks that were played previously in

the random sequence.

• During program play, random play or 1 track repeat

play, search operation is limited to the current track

only.

Press during play.

Press during stop mode.

Press again to resume play.

Total number of tracks

Total playing time.

Reverse Forward

Off mode

Auto power off function

If the unit is left in stop or paused status for approximately

10 minutes, the unit powers itself off automatically in order

to prevent the batteries from running down.

(If no disc is loaded in the unit, it powers itself off in 30 sec-

onds.)

Location of Controls

Sequential Play

Back panel of the unit

XL-PG5 Only

Mentuke_E(J) 1/26/99, 6:36 PM2

Product specificaties

Merk:	JVC
Categorie:	CD-spelers/recorder
Model:	XL-PV400

Heb je hulp nodig?

Als je hulp nodig hebt met JVC XL-PV400 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding CD-spelers/recorder JVC

JVC XL-FP10B Handleiding

3 Augustus 2023

JVC RD-E661B-DAB Handleiding

20 Juni 2023

JVC RD-E221B Handleiding

18 Juni 2023

JVC RC-EZ31B Handleiding

10 Juni 2023

JVC XL-V130BK Handleiding

25 Mei 2023

JVC XL-FZ700BK Handleiding

6 Mei 2023

JVC CH-X500 Handleiding

2 Mei 2023

JVC CH-X1500 Handleiding

2 Mei 2023

JVC CH-X350 Handleiding

19 April 2023

JVC RC-EX16A Handleiding

14 April 2023

Handleiding CD-spelers/recorder

Nieuwste handleidingen voor CD-spelers/recorder

S.M.S.L PL100 Handleiding

16 December 2024

Ruark Audio R-CD100 Handleiding

11 December 2024

Auna Stereosonic Handleiding

9 December 2024

Pioneer CD-SB10 Handleiding

7 December 2024

Taga Harmony TCD-50 Handleiding

20 November 2024

Marantz SA-17S1 Handleiding

15 November 2024

Klipsch PD-10AE Handleiding

13 November 2024

Rotel Michi Q5 Handleiding

3 November 2024

Reflexion PCD520MF Handleiding

29 September 2024

Auna Reference 802 Handleiding

24 September 2024