JL Audio VX800/8i Handleiding

JL Audio Receiver VX800/8i

Lees hieronder de 📖 handleiding in het Nederlandse voor JL Audio VX800/8i (2 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

6.62 in

168 mm

11.32 in

287 mm

5.53 in

141 mm

2.12 in

54 mm

10.22 in

260 mm

CONNECTION GUIDE

800W Full-Range 8-Channel Class D Amplier

with Integrated DSP

with

Thank you for purchasing a JL Audio amplifier for your sound system.

Your amplifier has been designed and manufactured to exacting

standards in order to ensure years of musical enjoyment. For maximum

performance, we highly recommend that you have your new amplifier

installed by an authorized JL Audio dealer. Your authorized dealer has

the training, expertise and installation equipment to ensure optimum

performance from this product. Should you decide to install the amplifier

yourself, please take the time to read this manual thoroughly to familiarize

yourself with its installation requirements and setup procedures.

If you have any questions regarding the instructions in this manual or any

aspect of your amplifier’s operation, please contact your authorized JL

Audio dealer for assistance. If you need further assistance, please contact

the JL Audio Technical Support Department at technical@jlaudio.com or

call (954) 443–1100 during business hours.

Installation Applications

This amplifier is designed for operation with 12 volt, negative-

ground electrical systems. Using this product in systems with positive

ground and/or voltages other than 12V may result in damage to the

product and will void the warranty. This product is not certified or

approved for use in aircraft.

Product Description

This is a eight-channel, full-range Class D amplifier equipped with the

second generation of JL Audio’s NexD™ high-speed switching technology.

It is engineered to deliver reference-grade audio amplification with

outstanding efficiency and unprecedented, built-in processing power.

Instead of traditional analog processing controlled by knobs and switches,

VXi amplifiers feature an integrated DSP (Digital Signal Processor). The

amplifier and its integrated DSP are configured using an external device

(PC, Tablet or Phone), with the appropriate JL Audio TüN™ application

installed. (See section for more info.)What is TüN?

Planning Your Installation

It is important that you take the time to read this manual thoroughly

and that you plan your installation carefully. It is very easy to damage

expensive vehicle systems in modern automobiles. Never assume that you

have found appropriate wires without consulting a reliable wiring diagram

or without analyzing with proper test equipment. If you are uncomfortable

or unfamiliar with reading diagrams or testing methods, please enlist the

services of your authorized JL Audio dealer to perform the installation.

Your authorized dealer has the training, expertise and installation

equipment to ensure optimum performance from this product.

The

following are some considerations that you must take into account when

planning your installation.

Safety Considerations

• Install your amplifier in a dry, well-ventilated location that

does not interfere with your vehicle’s safety equipment

(air bags, seat belt systems, ABS brake systems, etc.).

• Do not mount the amplifier in the engine

compartment or in any areas of extreme heat.

• Securely mount the amplifier so that it does not come

loose in the event of a collision/sudden jolt or as a result

of repeated vibrations during normal operation.

• Check before drilling to make sure that you will not be drilling into

a fuel tank, gas/brake line, wiring harness, or other vital system.

• Do not run system wiring outside or underneath the

vehicle/vessel. This is an extremely dangerous practice,

which can result in severe damage/injury.

• Take the necessary precautions when making

connections to the vehicle’s battery.

• Protect all system wires from sharp edges by carefully routing them,

tying them down and using grommets and loom where appropriate.

• Secure all wiring as needed, using cable ties or wire clamps

to protect them from moving parts and sharp edges.

Cooling Efficiency Considerations

The outer shell of your JL Audio amplifier is designed to remove heat

from the amplifier circuitry. For optimum cooling performance, this outer

shell should be exposed to as large a volume of air as possible. Enclosing

the amplifier in a small, poorly ventilated chamber can lead to excessive

heat build-up and degraded performance. If an installation calls for an

enclosure around the amplifier, we recommend that this enclosure be

ventilated with the aid of a fan. In normal applications, fan-cooling is not

necessary. If mounting the amplifier under a seat, make sure there is at

least 1 inch (2.5 cm) of space above the amplifier’s outer shell to permit

proper cooling.

What is Included

(1) Amplifier (1) Power Connector

(1) Analog Input Harness (2) Speaker Output Harnesses

(1) JL Audio Badge (4) Corner Caps

(1) USB A/B Cable (6 ft./1.8 m) (1) Corner Cap Tool

(2) Black Hex Cap Machine Screws (1) 2.5 mm Hex Wrench

(2) Silver Thumbscrews (1) 3 mm Hex Wrench

(1) Connection Guide

JL Audio Badge

To complement the amplifier’s mounting orientation, the logo badge

includes a recessed key feature allowing it to be affixed at 90 degree

increments on the amplifier’s top. To install, remove the adhesive backing

and press the badge at the desired orientation.

Corner Cap Installation and Removal

The corner caps are designed to conceal the amplifier’s mounting holes

and hardware. To install, simply press a corner cap into each mounting

hole. To avoid scratching the amplifier’s chassis during removal, use the

included, plastic corner cap tool and lift below each cap.

Making Connections

VXi amplifiers utilize removable plugs and harnesses to make the

following connections:

• Power Connector

To connect the power, ground and remote turn-on wires to the amplifier,

back out the set screws on the connector using the supplied hex

wrenches. Strip back 3/8 inch (10 mm) of insulation from the end of each

wire and insert the bare wire into the receptacle on the power connector

plug, seating it firmly so that no bare wire is exposed. While holding each

wire in place, tighten each set screw firmly, taking care not to strip the

head of the screw. Install the power connector by plugging it into the

amplifier’s power connector receptacle, pushing firmly.

• Analog Input Harness

This harness includes connections for Signal Input (RCA plugs), Preamp

Outputs (RCA plugs), Remote Turn-On Output (wire lead) and Valet Input

(wire lead). Select either the included black hex cap machine screws or

the silver thumbscrews to secure the Analog Input Harness connector to

the amplifier.

• Speaker Output Harnesses

These harnesses have output wire leads to connect with speaker cables.

Turn-On Mode

VXi amplifiers can be switched on and off using one of three methods,

configured by the “Turn On Mode” setting in the TüN™ Software Interface.

Refer to the table below for detailed info and decide which option is best

suited for your specific system.

Setting Mode Function Connection

Remote Conventional

(Preferred)

Turn-on/off controlled by your

source unit.

Connect your source unit +12V ’s

remote turn-on output to the

Power Connector’s Remote Turn-

On Input connection.

Offset

DC Offset

Sensing

(Auto)

Automatically turns on/off by

detecting the presence of small

DC signal in OEM audio outputs.

This circuit senses the Analog

Input 1 only. Note: The sensitivity

of this circuit is designed for high-

level (speaker level) signals, not for

low-level (preamp level) signals.

Make sure the OEM audio outputs

contain midrange signals.

Signal

Sensing

(Auto)

Automatically turns on by

detecting full-range OEM audio

signals and turns off after

the signal is removed (varies,

depending on input signal levels).

3 Speaker Output Harnesses

Connect the speaker output leads to the corresponding speaker wires.

4 JLid-COMM

Connect optional accessories (VXi-BTC, VXi-HUB, etc.) to this port.

5 JLid-CTRL

Connect optional DRC (Digital Remote Controller) wired controllers

to this port.

6 SD + Reset

Lift the dust cover to access the following utility functions:

Reset Buttons: Use a small pin to perform the following:

Reboot Amp - Press and release the right button.

Factory Reset (wipe memory, reboot amp) - Press and hold the left

button for 7 seconds.

DFU (Device Firmware Update) Mode: Press and release both

buttons simultaneously.

Micro SD Slot: For service/future expansion.

7 USB

This USB A/B port permits connection to a computer for configuration

and tuning, using the TüN™ Software.

8 DIGITAL-In

Toslink port accepts 2-channel digital audio signal from any optical

(S/PDIF) digital output, with a sample rate up to 192 kHz.

9 DIGITAL-Out

Provides a digital audio output (24 bit/96 kHz) that is not susceptible to

RF interference or noise-generating electrical conditions. By default, this

is a pass-through audio output, with no signal processing applied, and

intended for use with other equipment that have an optical (Toslink)

digital audio input (S/PDIF) port. Using the TüN™ Software Interface, you

may configure this output’s routing, equalization, output level and DRC

control functionality.

1 Power Connector

A. Run 2 AWG power wire from the positive (+12V) battery post to

the amplifier mounting location. If additional amplifiers are being

installed, run the appropriate gauge power wire for the combined,

maximum current draw, and install a fused distribution block near

the amplifiers.

B. An appropriate fuse (sold separately) at the main power wire(s) is

vital for vehicle safety. This fuse must be installed within 18 inches

(45 cm) of the battery post connection. If this is the only device con-

nected to this main wire, use a 80 A fuse. Do not install the fuse until

the power wire has been securely connected to the amplifier.

C. The ground connection should be made to a clean, solid metal

grounding point using 2 AWG wire, and kept as short as possible.

The metal surface of the grounding point should be sanded to create

a clean, metal-to-metal connection. For optimal grounding, we

recommend using a JL Audio ECS master ground lug (XB-MGLU). All

ground connections (source unit and amplifiers) should be made

at the same location.

D. The remote connection should be made to the source unit’s positive

(+12V) remote turn-on output. If your source unit does not have a

dedicated remote turn-on output, consider one of the alternative

turn-on options. (See Turn-On Mode section for more info.)

2 Analog Input Harness

The Analog Input Harness accepts the following connections:

Line-Level Analog Inputs: Eight female RCA jacks feed a differential-

balanced input section, providing a high degree of input flexibility, and

retaining superior noise rejection. This type of input architecture also

allows the VX800/8i to cleanly accept any analog audio signal up to 16

VRMS, without using a line-output converter.

Preamp Outputs: Two female, RCA jacks deliver line-level, analog audio

outputs (Max 4 V RMS) that are compatible with most types of aftermarket

equipment. These are configured with the TüN ™ Software Interface.

Remote: This connection provides a positive (+12V) turn-on voltage

(475 mA limit) to activate other aftermarket equipment (similar to an

aftermarket head unit’s remote turn-on lead).

Valet: When connected to negative ground, this connection activates the

Valet Mode Preset and will remain active until the ground connection is

removed. This preset is configured using the TüN ™ Software Interface and

will override any DRC controlled preset.

1 2 3

4 5 6 87 9

Limited Warranty – Amplifiers (USA)

JL Audio warrants this product to be free of defects in materials and workmanship

for a period of two (2) years from the original date of purchase. This warranty is

not transferrable and applies only to the original purchaser from an authorized

JLAudio dealer. Should service be necessary under this warranty for any reason due

to manufacturing defect or malfunction, JL Audio will (at its discretion), repair or

replace the defective product with new or remanufactured product at no charge.

Damage caused by the following is not covered under warranty: accident, misuse,

abuse, product modification or neglect, failure to follow installation instructions,

unauthorized repair attempts, misrepresentations by the seller. This warranty does

not cover incidental or consequential damages and does not cover the cost of

removing or reinstalling the unit(s). Cosmetic damage due to accident or normal

wear and tear is not covered under warranty.

Warranty is void if the product’s serial number has been removed or defaced.

Any applicable implied warranties are limited in duration to the period of the

express warranty as provided herein beginning with the date of the original

purchase at retail, and no warranties, whether express or implied, shall apply to

this product thereafter. Some states do not allow limitations on implied warranties,

therefore these exclusions may not apply to you. This warranty gives you specific

legal rights, and you may also have other rights, which vary from state to state.

If you need service on your JL AUDIO product:

All warranty returns should be sent to JL Audio ’s Amplifier Service Facility

freight-prepaid through an authorized JL Audio dealer and must be accompanied

by proof of purchase (a copy of the original sales receipt). Direct returns from

consumers or non-authorized dealers will be refused unless specifically authorized

by JL Audio with a valid return authorization number. Warranty expiration on

products returned without proof of purchase will be determined from the

manufacturing date code. Coverage may be invalidated as this date is previous

to purchase date. Non-defective items received will be returned freight-collect.

Customer is responsible for shipping charges and insurance in sending the

product to JL Audio. Freight damage on returns is not covered under warranty.

For Service Information in the U.S.A. please call

JL Audio Customer Service:

(954) 443-1100 9:00 AM – 5:30 PM (Eastern Time Zone)

JL Audio, Inc.

10369 North Commerce Pkwy. Miramar, FL 33025

(Do not send product for repair to this address)

International Warranties:

Products purchased outside the United States of America are covered

only by that country’s distributor and not by JL Audio, Inc.

VX800/8i_MAN_121917

Connections

Power Connector

Connection DescriptionWire Capacity

+12 VDC (+) 2 AWG Positive (+12V) Power Connection to Battery

Ground (–) 2 AWG Negative (GND) Chassis Ground Connection

Remote 18 to 10 AWG Positive (+12V) Remote Turn-On Input from Source Unit

Analog Input Harness

Label Plug/Wire

Color Description

Input 1 White RCA Channel 1 Signal Input

Input 2 Red RCA Channel 2 Signal Input

Input 3 White RCA Channel 3 Signal Input

Input 4 Red RCA Channel 4 Signal Input

Input 5 White RCA Channel 5 Signal Input

Input 6 Red RCA Channel 6 Signal Input

Input 7 White RCA Channel 7 Signal Input

Input 8 Red RCA Channel 8 Signal Input

Pre-Out Left White RCA Preamp Signal Output 1

Pre-Out Right Red RCA Preamp Signal Output 2

Remote Blue Positive (+12V) Turn-On Output (475 mA limit)

Valet Green Negative (GND) Ground Input (activates the Valet Mode Preset)

Speaker Output Harness

Label Wire Color Description

White

Ch. 1

(+) Positive Speaker Output Ch. 1&2 Bridged (+)

White/Black (–) Negative Speaker Output

Gray

Ch. 2

(+) Positive Speaker Output

Gray/Black (–) Negative Speaker Output Ch. 1&2 Bridged (–)

Green

Ch. 3

(+) Positive Speaker Output Ch. 3&4 Bridged (+)

Green/Black (–) Negative Speaker Output

Purple

Ch. 4

(+) Positive Speaker Output

Purple/Black (–) Negative Speaker Output Ch. 3&4 Bridged (–)

Cyan

Ch. 5

(+) Positive Speaker Output Ch. 5&6 Bridged (+)

Cyan/Black (–) Negative Speaker Output

Magenta

Ch. 6

(+) Positive Speaker Output

Magenta/Black (–) Negative Speaker Output Ch. 5&6 Bridged (–)

Teal

Ch. 7

(+) Positive Speaker Output Ch. 7&8 Bridged (+)

Teal/Black (–) Negative Speaker Output

Tan

Ch. 8

(+) Positive Speaker Output

Tan/Black (–) Negative Speaker Output Ch. 7&8 Bridged (–)

Data Connections

Label Type Description/Use

JLid-COMM RJ45 Jack Optional accessory connections (VXi-BTC, VXi-HUB, etc)

JLid-CTRL RJ45 Jack Optional DRC (Digital Remote Controller) connection

USB USB A/B Port Computer connection to congure TüN™ Software Interface

DIGITAL-In S/PDIF Port 2-channel, optical (Toslink) digital input

DIGITAL-Out S/PDIF Port 2-channel, optical (Toslink) digital output

SD + Reset

Reset Buttons Multifunction use (Reboot/Reset/Device Firmware Update mode)

Micro SD Slot Used for future expansion

Specifications

Amplier Specications

Amplier Topology 2nd-Gen NexD™ High Speed Class D

Power Supply Unregulated MOSFET switching type

Recommended Power/GND Wire 2 AWG

Recommended Fuse 80 A

Standby Current Draw 2.4 mA

Input Voltage Range 200 mV - 16 V RMS

Rated RMS Power @ 14.4V,

<1% THD+N

75W x 8

@ 4 Ω

100W x 8

@ 2 Ω

200W x 4

@ 4 Ω Bridged

Rated RMS Power @ 12.5V,

<1% THD+N

60W x 8

@ 4 Ω

90W x 8

@ 2 Ω

180W x 4

@ 4 Ω Bridged

Frequency Response 12 Hz - 21 kHz (+0, -1dB)

Analog

Inputs

S/N Ratio,

(A-weighted, 20 kHz

noise bandwidth)

99 dB (Referred to rated power),

80 dB (Referred to 1 W)

Digital

Input

S/N Ratio,

(A-weighted, 20 kHz

noise bandwidth)

101 dB (Referred to rated power),

82 dB (Referred to 1 W)

Damping Factor >100 / 50 Hz @ 4 Ω, >50 / 50 Hz @ 2 Ω

DSP Specications

Processor AKM AK7738, processing at 24 bit/96 kHz

Analog

Inputs

Type Line-Level, Dierential-Balanced

Number of Channels 8, via harness-mounted female RCA jacks

Digital

Input

Type S/PDIF Optical via chassis-mounted Toslink port

Bit Depth/Sample Rate

Up to 24 bit/192 kHz

Analog

Outputs

Type 2 Line-Level, via harness-mounted female RCA jacks

Max Output Level 4 V RMS

Digital

Output

Type S/PDIF Optical via chassis-mounted Toslink port

Bit Depth/Sample Rate 24 bit/96 kHz

Dimensions

L x W x H 11.32 in x 6.62 in x 2.12 in / 287 mm x 168 mm x 54 mm

What is TüN?

TüN™ is software that you use to configure, tune and control your VXi

amplifier, and other JL Audio DSP products. TüN™ automatically recognizes

what it is connected to, and allows you to make adjustements with a

clear interface specifically set up for that product. TüN™ is available for

download for free in a variety of applications, for computers and most

handheld devices. For more information, visit: jlaudio.com/tun

For Windows® PC or Mac® computers, TüN™ connects via

USB and offers complete control and command of the entire

VXi feature set from the comfort of your desk or driver’s seat.

Software also runs in demo mode, without connected amplifiers,

for offline setup or demo purposes. Test drive it for free!

For iPad or Android tablets. Enjoy the full-featured TüN™ software

experience on your tablet, with the freedom of a wireless connection

via Bluetooth®. Requires VXi-BTC Bluetooth® Communicator.

Wireless connection and streamlined options, for fast and simple

amplifier setup. Download TüN™ Express for iPhone, iPad and Android

phones & tablets. Requires VXi-BTC Bluetooth® Communicator.

+12 VDC - Positive (+12V) Battery Connection

Ground - Negative (–) Ground Connection

Remote - Positive (+12V) Turn-On Input From Source Unit

Input 6 - Ch. 6 Input

Input 5 - Ch. 5 Input

Input 8 - Ch. 8 Input

Input 7 - Ch. 7 Input

Input 2 - Ch. 2 Input

Input 1 - Ch. 1 Input

Pre-Out Right - Analog Preamp Output

Pre-Out Left - Analog Preamp Output

Remote - Turn-On Output (+12V)

Valet - Valet Preset Toggle (–)

Input 4 - Ch. 4 Input

Input 3 - Ch. 3 Input

D - To Speaker(s): (+ and –)

C - To Speaker(s): (+ and –)

H - To Speaker(s): (+ and –)

G - To Speaker(s): (+ and –)

B - To Speaker(s): (+ and –)

A - To Speaker(s): (+ and –)

F - To Speaker(s): (+ and –)

E - To Speaker(s): (+ and –)

Included

Not Included

ANALOG AUDIO INPUTS

SPEAKER OUTPUTS

Wiring Diagram - VX800/8i

ABCD EFGH

JLid-COMM - Optional Network Hub or

Bluetooth® Communicator Connection (Sold Separately)

JLid-CTRL - Optional Digital Remote Controller

(DRC) Connection (Sold Separately)

DIGITAL-In - From Optical Digital (S/PDIF) Source

DIGITAL-Out - To Optical Digital (S/PDIF) Input on Next Device

USB A/B Cable - To Computer with TüN™ software installed

Standard CAT5 Network Cables

Optical Audio Cables

Product specificaties

Merk:	JL Audio
Categorie:	Receiver
Model:	VX800/8i

Heb je hulp nodig?

Als je hulp nodig hebt met JL Audio VX800/8i stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Receiver JL Audio

JL Audio XDM800/8-24V Handleiding

9 Juli 2024

JL Audio XDM600/6-24V Handleiding

9 Juli 2024

JL Audio MHD600/4-24V Handleiding

9 Januari 2024

JL Audio MHD900/5-24V Handleiding

9 Januari 2024

JL Audio M800/8-24V Handleiding

9 Januari 2024

JL Audio MX500/1 Handleiding

6 Juni 2023

JL Audio XD600/6v2 Handleiding

9 Mei 2023

JL Audio XDM300/1 Handleiding

9 Mei 2023

JL Audio XDM600/1 Handleiding

7 Mei 2023

JL Audio XD200/2v2 Handleiding

2 Mei 2023

Handleiding Receiver

Nieuwste handleidingen voor Receiver

Henry Engineering AES DIGITAL DA 2X4 Handleiding

21 November 2024

Deaf Bonce Machete MLA-70.2XS Handleiding

20 November 2024

QSC PowerLight 9.0 Handleiding

20 November 2024

Ashly FX-125.4 Handleiding

20 November 2024

JBL Power P80.2 Handleiding

20 November 2024

JBL Power Px600.2 Handleiding

20 November 2024

JBL Power P-4020 Handleiding

20 November 2024

JBL Power P180.2 Handleiding

20 November 2024

JBL Power BPx1100.1 Handleiding

20 November 2024

JBL Power BPx500.1 Handleiding

20 November 2024