JL Audio Stealthbox SB-Y-YXZ1SPKR/M3-650i Handleiding

JL Audio Speaker Stealthbox SB-Y-YXZ1SPKR/M3-650i

Lees hieronder de ๐Ÿ“– handleiding in het Nederlandse voor JL Audio Stealthbox SB-Y-YXZ1SPKR/M3-650i (8 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
Enclosure Type: Sealed
Driver Type: M3-650X-S-Gm-i
Nominal Impedance: 4 ohms
Continuous Power Handling: 60 watts (RMS method)
Thank you for choosing a JL Audio Stealthboxยฎ for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthboxยฎ installed by your
authorized JL Audio dealer. The installation professionals employed by your
dealer have the necessary tools and experience to disassemble and reassemble
your vehicle properly. If you prefer to perform your own installation, please read
this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely
vital that the Stealthboxยฎ be properly mounted to the vehicle
according to these instructions. Failure to mount the enclosure
properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the
enclosure caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a
collision or sudden deceleration.
INSTALLAT ION
DIFFICULTY:
ESTIMATED TIME:
1 HOUR
Continued on Next Page
15
OUT
OF
SB-Y-YXZ1SPKR/M3-650i INSTR_SKU# 011544
I N S T A L L A T I O N G U I D E
for the
SB-Y-YXZ1SPKR/M3-650i
SKU# 94678
2016 & Up Yamaha YXZ1000R
IN CLU DE D HAR DWA R E
1
2
3
4
Continued on Next Page
Page 2 โ€ข JL Audio, Inc., 2019
SB-Y-YXZ1SPKR/M3-650i INSTR_SKU# 011544
Note: For optimum performance, JL Audio recommends applying the included Foam Strips (or sound damping material) to surrounding plastic panels to reduce unwanted vibrations.
(hardware pictured for one)
* Pre-installed on enclosure
BOM ID DescriptionQty SKU
1 4 153820
1/4 - 20 x 1โ€ Stainless Steel Hex Cap Screw
2 4 153819 1/4โ€ Stainless Steel Split Lock Washer
3 4 153738 1/4โ€ Stainless Steel Flat Washer
4* 2 152414 Wire Harness (10โ€™)
- 1 150249 Foam Tape (not shown)
W IR I N G IN F O R M AT I O N
Continued on Next Page
Page 3 โ€ข JL Audio, Inc., 2019
SB-Y-YXZ1SPKR/M3-650i INSTR_SKU# 011544
Direct LED Wiring
Alternatively, you may hard wire individual leads or a combination
of leads to achieve up to seven different LED color assortments.
Refer to the table below for the wire colors used to achieve specific
LED colors.
LED Color Wire Color(s) Connection
Red Red
Combine selected wires from
all speakers and connect to
negative ground or the
negative (โ€“) battery post.
Green Green
Blue Blue
Yellow Red and Green
Pink Red and Blue
Aqua Green and Blue
White Red, Green and Blue
Combine all YELLOW (+12V) leads together (parallel) and connect to a
switched +12V supply.
LED Wiring Considerations
โ€ข For short-circuit protection, we recommend installing a fuse (not
included) at EACH speakerโ€™s YELLOW (+12V) LED power connection
lead.
โ€ข We recommend activating the speakersโ€™ LEDs thru an interior
lighting circuit that supplies +12V via an existing switch. If an exist-
ing switched circuit is not available, you may install a dedicated
toggle/rocker style switch that will supply positive (+12V) power.
Fuse this main +12V connection according to the total demands of
all LED circuits.
Wiring Harness Info
Wire Size Wire Color Use
16 AWG Red/Stripe Speaker Positive (+)
Black/Stripe Speaker Negative (โ€“)
20 AWG
Red Red RGB LED Negative (โ€“)
Green Green RGB LED Negative (โ€“)
Blue Blue RGB LED Negative (โ€“)
Yellow Main RGB LED Positive (+)
Adjustable control of RGB lighting may be achieved with the use of
an RGB lighting controller (sold separately). Note: When selecting
an RGB lighting controller, make sure that the total amperage
demands of all LED circuits does not exceed the output
capacity of the controller. For each M3-650X speaker, a 150 mA
fuse is recommended. For optimal performance, we recommend
using the JL Audio marine lighting controller (MLC-RW).


Product specificaties

Merk: JL Audio
Categorie: Speaker
Model: Stealthbox SB-Y-YXZ1SPKR/M3-650i

Heb je hulp nodig?

Als je hulp nodig hebt met JL Audio Stealthbox SB-Y-YXZ1SPKR/M3-650i stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker JL Audio

Handleiding Speaker

Nieuwste handleidingen voor Speaker