JL Audio SlamPak SLPK-CAN-SPYDER1 Handleiding

JL Audio Hifi systeem SlamPak SLPK-CAN-SPYDER1

Lees hieronder de 📖 handleiding in het Nederlandse voor JL Audio SlamPak SLPK-CAN-SPYDER1 (8 pagina's) in de categorie Hifi systeem. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
I N S T A L L A T I O N G U I D E
for the
SLPK-CAN-SPYDER1
SKU#94491& 94490
Thank you for choosing a JL Audio Slampak® for your motorcycle sound system. With proper
installation, your new vehicle-specific enclosed sound system will deliver years of listening pleasure.
We strongly recommend that you have your new Slampak
® installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage
extends to 2 years if your system is installed or approved by your authorized JL Audio dealer. If you
prefer to perform your own installation, please read this installation guide completely
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox ® be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
S T E P 1
Empty out the front storage space of the motorcycle so that
you have a clean area to work in.
If you are only installing the pods, skip to STEP 16.
Continued on Next Page
S T E P 2
Remove the bottom panel above the rear tire as show here
S T E P 3
Lift the seat, remove the panel that simulates a gas tank at
the top center of the motorcycle. Remove the two panels
labelled “can-am” (one on each side of the motorcycle) and
the two panels labelled “spyder” (one on each side of the
motorcycle).
SLPK-CAN-SPYDER1_INSTR_SKU# 011312
INSTALLATION
D I F F I C U LT Y :
35
OUT
OF
ESTIMATED TIME:
5 HOURS
SlamPak
Continued on Next Page
SLPK-CAN-SPYDER1_INSTR_SKU# 011312
S T E P 7
Looking down from the top front of the storage
compartment, notice where the wire loom enters the
compartment.
S T E P 6
The harness for power, ground, remote turn on, signal and
speakers will come down the right side of the motorcycle
and enter the storage compartment in the upper right rear
corner as shown below.
S T E P 5
Remove the front Air dam.
S T E P 4
Remove the air duct body panels as indicated by the image
at left. (One on each side of the motorcycle). There may be
auxiliary lights installed in this panel, unplug them as the
panel is removed.
If you are ONLY installing the pods and the full NOT
system, but will be installing an amplifier in the front storage
compartment, only remove the air duct body panel on
the right hand side (where the harness enters the storage
compartment (as seen in STEP 5 below), skip to STEP 6.
Page 2 • JL Audio, Inc 2010
If you are ONLY installing the pods and the full system, NOT
skip to STEP 16.
The two templates shown can be found on the last two
pages of the install manual, cut them out and position them
as shown.
Remove the panel directly above the storage compartment
as indicated by the arrow.
Mount the bevelled hole trims as shown using the 8
supplied #6-1 x 3/4” Phillips head screws (4 per trim).
Mark the center positions of each template and cut the two
holes, the holes should be 3-5/8” in diameter after they are
cut.
USE ALL PRECAUTIONS WHEN CUTTING/DRILLING!
Looking up from the front right tire, use a 1-1/8” hole- saw
to cut a hole for the harness to come through as seen in
STEP 7.
Before drilling, always make sure that you are not
going to be drilling into any gas lines, brake lines,
tires, transmission lines, electrical wiring, exhaust
systems or anything else that might cause a
reduction in your weekly pay.
Always wear eye protection when drilling!
Continued on Next Page
SLPK-CAN-SPYDER1_INSTR_SKU# 011312
S T E P 1 5
Install the 3/8-16 x 1-1/4” Hex Head Bolt through the included
Split Lock Washer, the 1-1/4” Fender Washer and the hole
drilled in STEP 14 into the enclosure, tighten this fastener
down.
Once this fastener is tight, the front air dam can be re-
installed.
S T E P 1 4
Drill a 5/16” hole where the indentation was made in STEP 13.
Before drilling, always make sure that you are not
going to be drilling into any gas lines, brake lines,
tires, transmission lines, electrical wiring, exhaust
systems or anything else that might cause a
reduction in your weekly pay.
Always wear eye protection when drilling!
S T E P 1 3
Thread the 3/8-16 x 1-1/4” Hex Head Bolt all the way into
the enclosure. Press the enclosure down into the storage
compartment towards the right front corner, the Hex Head
Bolt will leave an indentation in the wax square.
Once you’ve confirmed the indentation in the wax square,
remove the Hex Head Bolt from the enclosure.
S T E P 1 2
Looking down and towards the front right corner of the
storage compartment, position the wax square as shown.
Page 3 • JL Audio, Inc 2010
Put a length of masking tape as shown on each side of the
top fairing.
Align pod with the back edge matching the fairing (as
shown) and the front corners as show in STEP 20.
Remove the larger speaker from each pod, the smaller
speaker can remain in the pod. The speakers are only
secured in the pods for shipping with 3- screws, use all six
when re-installing. (In the following pictures, both speakers
have been removed, this is NOT necessary!)
Position foam strips as shown on each pod.
Note the location of the three holes in the pods, two will be
used to mount the pod, the third will be the wire run.
Remove gauge cluster as shown by lifting top panel then
depressing two locking tabs on top of the cluster.

Product specificaties

Merk: JL Audio
Categorie: Hifi systeem
Model: SlamPak SLPK-CAN-SPYDER1

Heb je hulp nodig?

Als je hulp nodig hebt met JL Audio SlamPak SLPK-CAN-SPYDER1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Hifi systeem JL Audio

JL Audio

JL Audio J2 500.1 Handleiding

4 April 2023
JL Audio

JL Audio J2 250.1 Handleiding

1 April 2023
JL Audio

JL Audio J2 360.2 Handleiding

30 Maart 2023
JL Audio

JL Audio G1700 Handleiding

26 Maart 2023
JL Audio

JL Audio J2 1000.1 Handleiding

14 Maart 2023
JL Audio

JL Audio XD6001 Handleiding

14 Maart 2023
JL Audio

JL Audio XD400/4 Handleiding

28 Februari 2023
JL Audio

JL Audio J2 320.4 Handleiding

14 Februari 2023
JL Audio

JL Audio MX600/3 Handleiding

12 Februari 2023
JL Audio

JL Audio SlamPak SLPK-CAN-SPYDER1 Handleiding

30 Januari 2023

Handleiding Hifi systeem

Nieuwste handleidingen voor Hifi systeem

Vaxis

Vaxis Atom 500 Handleiding

1 April 2025
INKEE

INKEE Benbox Handleiding

31 Maart 2025
Energy Sistem

Energy Sistem Tower 7 True Wireless Handleiding

28 Maart 2025
Teradek

Teradek Spark 4K Handleiding

28 Maart 2025
Teradek

Teradek Bolt 4K LT 750 Handleiding

28 Maart 2025
Teradek

Teradek Bolt 4K 1500 Handleiding

28 Maart 2025
Teradek

Teradek Cube 675 Handleiding

28 Maart 2025
Teradek

Teradek Bolt 1000 XT Handleiding

28 Maart 2025
Teradek

Teradek Cubelet 605 Handleiding

28 Maart 2025
Teradek

Teradek Cube 755 Handleiding

28 Maart 2025