JL Audio MV700/5i Handleiding

JL Audio Receiver MV700/5i

Lees hieronder de 📖 handleiding in het Nederlandse voor JL Audio MV700/5i (3 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/3
13.34 in
339 mm
13.96 in
355 mm
6.93 in
176 mm
3.67 in
93 mm
2.05 in
52 mm
CONNECTION GUIDE
700W 5-Channel Class D Marine System
Amplier with Integrated DSP
with
1234
5 6 7
Thank you for purchasing a JL Audio amplifier for your marine sound system.
Your amplifier has been designed and manufactured to exacting standards in order to ensure years of musical
enjoyment in your vessel. For maximum performance, we highly recommend that you have your new amplifier installed
by an authorized JL Audio dealer. Your authorized dealer has the training, expertise and installation equipment to ensure
optimum performance from this product. Should you decide to install the amplifier yourself, please take the time to read
this manual thoroughly to familiarize yourself with its installation requirements and setup procedures.
If you have any questions regarding the instructions in this manual or any aspect of your amplifier’s operation, please
contact your authorized JL Audio dealer for assistance. If you need further assistance, please contact the JL Audio
Technical Support Department at technical@jlaudio.com/support.
Installation Applications
This amplifier is designed for operation with 12 volt DC, negative-ground electrical systems. Using this product in vessels
with positive ground and/or voltages other than 12V DC may result in damage to the product and will void the warranty.
This product is not certified or approved for use in aircraft.
Planning Your Installation
It is important that you take the time to read this manual thoroughly and that you plan your installation carefully. It is
very easy to damage electrical systems in modern vessels. Never assume that you have found appropriate wires without
consulting a reliable wiring diagram or without analyzing using proper test equipment. If you are uncomfortable or
unfamiliar with diagrams or testing methods, please enlist the services of your authorized JL Audio dealer to perform
the installation. Your authorized dealer has the training, expertise and installation equipment to ensure optimum
performance from this product.
The following are some considerations that you must take into account when planning
your installation.
Safety Considerations
• Install your amplifier in a dry, well-ventilated location that does not interfere with factory installed systems.
• This product should never be submerged under water or subjected to high-pressure water spray.
• Do not install where it will be directly exposed to the elements, or in the engine compartment, or in any areas of
extreme heat. Areas exposed to a heater or hot air should also be avoided.
• When selecting a mounting location, consider the orientation of the amplifier and its associated connections.
If possible, position the amplifier vertically, with all connections pointing downward. Wiring and cables
should be routed to direct potential condensation and moisture away from the amplifier.
• Securely mount the amplifier so that it does not come loose in the event of a collision or sudden jolt, or as a result
of repeated vibrations during normal operation.
• Check before drilling to make sure that you will not be drilling into an exterior panel/hull, fuel tank, fuel line,
wiring harness, or other vital system.
• Do not run system wiring outside or underneath the vessel. This is an extremely dangerous practice, which can
result in severe damage/injury.
• Protect all system wires from sharp edges by carefully routing them, tying them down and using grommets and
loom, where appropriate.
• Secure all wiring as needed, using cable ties or wire clamps to protect them from moving parts and sharp edges.
1 Power Connector
The MV700/5i’s “+12 VDC” and “Ground” connections are designed to accept up to 4 AWG copper wire. Note: Copper Clad
Aluminum (CCA) wire is not recommended. Tinned copper power wire is the best choice for marine installations. 4 AWG is the
minimum copper wire size for this amplifier.
To connect the power, ground and remote turn-on wires to the amplifier, back out the set screws on the connector using
the supplied hex wrenches. Strip back 3/8 inch (10 mm) of insulation from the end of each wire and insert the bare wire
into the receptacle on the power connector plug, seating it firmly so that no bare wire is exposed. While holding each
wire in place, tighten each set screw firmly, taking care not to strip the head of the screw. Install the power connector by
plugging it into the amplifier’s power connector receptacle, pushing firmly.
A. +12 VDC: Run copper wire from the positive (+12V) battery post to the amplifier mounting location. If additional
amplifiers are being installed, run the appropriate gauge copper wire for the combined, maximum current draw, and
install a fused distribution block near the amplifiers.
B. An appropriate fuse or ignition-protected circuit breaker (sold separately) at the main power wire(s) is vital for vessel
safety. This must be installed within 7 inches (18 cm) of the battery post connection or in compliance with marine
industry standards. If this is the only device connected to this main wire, use a 60 A value. Do not install the fuse or
close the circuit breaker until the power wire has been securely connected to the amplifier and all other connections
have been made.
C. Ground: This connection should be made to the NEGATIVE battery post. Alternatively, an appropriately equipped and
positioned DC ground bus bar near the battery may be used. All ground connections (source unit and amplifiers)
should be made at the same location.
D. Remote: This connection should be made to the source unit’s positive (+12V) remote turn-on output. If your source
unit does not have a dedicated remote turn-on output, the amplifier’s remote turn-on connection can be connected
to +12V via a switch that derives power from an ignition-switched circuit.
2 Input Section
Eight female RCA jacks feed a differential-balanced input section, providing a high degree of input flexibility, and retaining
superior noise rejection. This type of input architecture also allows the MV700/5i to cleanly accept any analog audio signal
up to 16 VRMS, without using a line-output converter.
3 Pre-Outs
Six female, RCA jacks deliver line-level, analog audio outputs (Max 4 V RMS) that are compatible with most types of
aftermarket equipment. These are configured with the TüN ™ Software Interface.
Product Description
The MV700/5i is a five-channel, Class D marine system amplifier equipped with NexD2™, the second generation of JL Audio’s
high-speed switching technology. It is engineered to deliver reference-grade audio amplification with outstanding efficiency
while also incorporating unprecedented processing power. Instead of traditional analog processing controlled by knobs
and switches, MVi amplifiers feature an integrated DSP (Digital Signal Processor). The amplifier and its integrated DSP are
configured using an external device (PC, Tablet or Phone), with the appropriate JL Audio TüN™ application installed. (See
What is TüN? section for more info.)
What is Included
(1) Amplifier (4) Mounting Screws
(1) Power Connector (1) 2.5 mm Hex Wrench
(2) Speaker Output Harnesses (1) 3 mm Hex Wrench
(1) Subwoofer Output Harness (1) Connection Guide
(1) USB A/B Cable (6 ft./1.8 m)
Cooling Efficiency Considerations
The outer shell of your JL Audio amplifier is designed to remove heat from the amplifier circuitry. For optimum cooling
performance, this outer shell should be exposed to as large a volume of air as possible. Enclosing the amplifier in a
small, poorly ventilated chamber can lead to excessive heat build-up and degraded performance. If an installation calls
for an enclosure around the amplifier, we recommend that this enclosure be ventilated with the aid of a fan. In normal
applications, fan-cooling is not necessary. When mounting the amplifier in an enclosed compartment, make sure there is at
least 1 inch (2.5 cm) of space above the amplifier’s outer shell to permit proper cooling.
Mounting Considerations
MV amplifiers are equipped with keyhole style
mounting holes to simplify installations in confined
spaces or vertical-mount applications. Mounting screws
may be preinstalled, allowing amplifier connections
to be made prior to securing in its final location. See
diagram at right.
When selecting the installation location, consider
the mounting orientation of the amplifier and its
associated connections. If possible, position the
amplifier vertically, with all connections pointing
downward. Wiring and cables should be routed to
direct potential condensation and moisture away
from the amplifier. When installed in this manner, the
amplifier achieves an IPX2 water-resistance rating.
4 Speaker Output Harnesses
Connect the speaker output leads to the corresponding speaker wires. These harnesses and their companion cables are
equipped with water-resistant connectors for maximum connection integrity in marine environments.
5 JLid-COMM
Connect optional accessories (MVi-HUB, M-DRC-50, VXi-BTC, MVi-DRCADAPT, etc.) to this port.
6 USB
This USB A/B port permits connection to a computer for configuration and tuning, using TüN™ Software.
7 Reset Buttons
Use a small pin to perform the following:
(A) Factory Reset (wipe memory, reboot amp) - Press and hold the button for 7 seconds. All user settings will be
erased and the amplifier will revert to its factory settings!
(B) Reboot Amplifier - Press and release the button. Previous user settings will be retained.
LED Status/Condition Reporting
LEDs located on the chassis top and connection panel are used to communicate amplier status and condition. Refer to the
table below for the location and meaning for each behavior.
LED / Location Behavior Status/Condition›
LED / Amplier Top
Flashing Blue Critical Voltage (too low)
Flashing Red Critical Temperature (too hot)
Flashing Yellow Excessive Output Current (low impedance/short)
Upper Left LED / JLid-COMM Port
Green Detecting JLid™ Device
Blue JLid™ Connection Success
Yellow Invalid JLid™ Device
Flashing Red Excessive Current on JLid Port
Upper Right LED / JLid-COMM Port
Flashing Red
Critical Voltage/Temperature
Excessive Remote Output Current
Green Active Connection with TüN™ Software
Limited Warranty – Marine Amplifiers (USA)
JL Audio warrants this product to be free of defects in materials and workmanship for a period of two (2) years
from the original date of purchase. This warranty is not transferable and applies only to the original purchaser
from an authorized JL Audio dealer. Should service be necessary under this warranty for any reason due to
manufacturing defect or malfunction, JL Audio will (at its discretion), repair or replace the defective product with
new or remanufactured product at no charge. Damage caused by the following is not covered under warranty:
accident, misuse, abuse, product modification or neglect, failure to follow installation instructions, unauthorized
repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential
damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident
or normal wear and tear is not covered under warranty.
Products installed as original equipment by boat manufacturers are covered by the boat manufacturer’s
warranty, not JL Audio, Inc.
Warranty is void if the product’s serial number has been removed or defaced.
Any applicable implied warranties are limited in duration to the period of the express warranty
as provided herein beginning with the date of the original purchase at retail, and no warranties,
whether express or implied, shall apply to this product thereafter. Some states do not allow
limitations on implied warranties, therefore these exclusions may not apply to you. This warranty
gives you specific legal rights, and you may also have other rights, which vary from state to state.
If you need service on your JL AUDIO product:
All warranty returns should be sent to JL Audio ’s Amplifier Service Facility freight-prepaid through an authorized
JL Audio dealer and must be accompanied by proof of purchase (a copy of the original sales receipt). Direct
returns from consumers or non-authorized dealers will be refused unless specifically authorized by JL Audio with
a valid return authorization number. Warranty expiration on products returned without proof of purchase will be
determined from the manufacturing date code. Coverage may be invalidated as this date is previous to purchase
date. Non-defective items received will be returned freight-collect. Customer is responsible for shipping charges
and insurance in sending the product to JL Audio. Freight damage on returns is not covered under warranty.
For Service Information in the U.S.A. please call
JL Audio Customer Service:
(954) 443-1100 9:00 AM – 5:30 PM (Eastern Time Zone)
JL Audio, Inc.
10369 North Commerce Pkwy. Miramar, FL 33025
(Do not send product for repair to this address)
International Warranties:
Products purchased outside the United States of America are covered only
by that country’s distributor and not by JL Audio, Inc.
MV700/5i_MAN_071519
Connections
Power Connector
Connection DescriptionWire Capacity
+12 VDC (+) 2 AWG Positive (+12V) Battery Connection
Ground (–) 2 AWG Negative (GND) Battery Connection
Remote 18 to 10 AWG Positive (+12V) Remote Turn-On Input from Source Unit
Input Section
Label RCA Jack Description
CH. 1 Black RCA Channel 1 Signal Input
CH. 2 Red RCA Channel 2 Signal Input
CH. 3 Black RCA Channel 3 Signal Input
CH. 4 Red RCA Channel 4 Signal Input
CH. 5 Black RCA Channel 5 Signal Input
CH. 6 Red RCA Channel 6 Signal Input
CH. 7 Black RCA Channel 7 Signal Input
CH. 8 Red RCA Channel 8 Signal Input
Pre-Outs (with independent DSP)
Label RCA Jack Description
P. 1 Black RCA Preamp Signal Output 1
P. 2 Red RCA Preamp Signal Output 2
P. 3 Black RCA Preamp Signal Output 3
P. 4 Red RCA Preamp Signal Output 4
P. 5 Black RCA Preamp Signal Output 5
P. 6 Red RCA Preamp Signal Output 6
Connections
Speaker Outputs
Label Wire Color Description
A
White (+) Positive Speaker Output Ch. 1&2 Bridged (+)
White/Black (–) Negative Speaker Output
B
Gray (+) Positive Speaker Output
Gray/Black (–) Negative Speaker Output Ch. 1&2 Bridged (–)
C
Green (+) Positive Speaker Output Ch. 3&4 Bridged (+)
Green/Black (–) Negative Speaker Output
D
Purple (+) Positive Speaker Output
Purple/Black (–) Negative Speaker Output Ch. 3&4 Bridged (–)
SUB
Brown (+) Positive Subwoofer Output
Brown/White (–) Negative Subwoofer Output
Data Connections
Label Type Description/Use
JLid-COMM RJ45 Jack Optional accessory connections (MVi-HUB, VXi-BTC, etc)
USB USB A/B Port Computer connection to congure TüN™ Software Interface
Reset
Button - A Factory Reset (wipe memory, reboot amp) - Press and hold
for 7 seconds.
Button - B Reboot Amp - Press and release.
Specifications
Amplier Specications
Amplier Topology 2nd-Gen NexD™ High Speed Class D
Power Supply Type Unregulated MOSFET Switching
Operating Voltage 10 - 15V DC
Min. Copper Power/GND Wire 4 AWG
Recommended Fuse 60 A
Standby Current Draw 2.5 mA
Rated RMS Power @ 14.4V,
<1% THD+N
Main @ 4 Ω
75W x 4
Main @ 2 Ω
100W x 4
Main @ 4 Ω Bridged
200W x 2
Sub @ 4 Ω
180W x 1
Sub @ 3 Ω
240W x 1
Sub @ 2 Ω
300W x 1
Rated RMS Power @ 12.5V,
<1% THD+N
Main @ 4 Ω
60W x 4
Main @ 2 Ω
90W x 4
Main @ 4 Ω Bridged
180W x 2
Sub @ 4 Ω
180W x 1
Sub @ 3 Ω
240W x 1
Sub @ 2 Ω
300W x 1
Frequency Response Main: 12 Hz - 24 kHz (+0, -1dB)
Sub: 12 Hz - 1 kHz (+0, -1dB)
Damping Factor Main: >100 / 50 Hz @ 4 Ω, >50 / 50 Hz @ 2 Ω
Sub: >100 / 50 Hz @ 4 Ω, >50 / 50 Hz @ 2 Ω
IP Rating IPX2 (when mounted vertically with
connections pointed downward)
DSP Specications
Processor AKM AK7738, processing at 24 bit/48 kHz
Analog Inputs
Type Line-Level, Dierential-Balanced
Number of Channels 8, via chassis-mounted female RCA jacks
Input Voltage Range 250 mV - 16 V RMS
S/N Ratio,
(A-weighted, 20 kHz
noise bandwidth)
Main: 99 dB (Referred to rated power),
80 dB (Referred to 1 W)
Sub: 99 dB (Referred to rated power),
72 dB (Referred to 1 W)
Analog
Preouts
Type 6 Line-Level, via chassis-mounted female RCA jacks
Max Output Level 4 V RMS
Dimensions
L x W x H 13.96 in x 6.93 in x 2.05 in / 355 mm x 176 mm x 52 mm
What is TüN?
TüN™ is software that you use to configure, tune and control
your MVi amplifier, and other JL Audio DSP products. TüN™
automatically recognizes what it is connected to, and allows you
to make adjustments with a clear interface specifically set up for
that product. TüN™ is available for download for free in a variety of
applications, for computers and most handheld devices. For more
information, visit: jlaudio.com/tun
For Windows® PC or Mac® computers, TüN™ connects via
USB and offers complete control and command of the entire
MVi feature set from the comfort of your desk or driver’s seat.
Software also runs in demo mode, without connected amplifiers,
for offline setup or demo purposes. Test drive it for free!
For iPad or Android tablets. Enjoy the full-featured TüN™ software
experience on your tablet, with the freedom of a wireless connection
via Bluetooth®. Requires VXi-BTC Bluetooth® Communicator.
Wireless connection and streamlined options, for fast and simple
amplifier setup. Download TüN™ Express for iPhone, iPad and Android
phones & tablets. Requires VXi-BTC Bluetooth® Communicator.
Wiring Diagram - MV700/5i
Attached to Amp
Included
Not Included
Standard CAT5 Network Cable
SPEAKER
OUTPUTS
CH. 1 - Ch. 1 Signal Input
CH. 2 - Ch. 2 Signal Input
+12 VDC - Positive (+12V) Battery Connection
Ground - Negative (–) Ground Connection
Remote - Positive (+12V) Turn-On Input From Source Unit
JLid-COMM - Optional Digital Remote Controller, Network Hub or
Bluetooth® Communicator Connection (Sold Separately)
USB A/B Cable -
To Computer with TüN™ software installed
ANALOG
INPUTS
CH. 3 - Ch. 3 Signal Input
CH. 4 - Ch. 4 Signal Input
CH. 5 - Ch. 5 Signal Input
CH. 6 - Ch. 6 Signal Input
CH. 7 - Ch. 7 Signal Input
CH. 8 - Ch. 8 Signal Input
ANALOG
PREAMP
OUTPUTS
P. 2 - Preamp Signal Output 2
P. 1 - Preamp Signal Output 1
P. 4 - Preamp Signal Output 4
P. 3 - Preamp Signal Output 3
P. 6 - Preamp Signal Output 6
P. 5 - Preamp Signal Output 5
D - To Speaker(s): (+ and –)
B - To Speaker(s): (+ and –)
C - To Speaker(s): (+ and –)
A - To Speaker(s): (+ and –)
SUB - To Subwoofer(s): (+ and –)

Product specificaties

Merk: JL Audio
Categorie: Receiver
Model: MV700/5i

Heb je hulp nodig?

Als je hulp nodig hebt met JL Audio MV700/5i stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Receiver JL Audio

JL Audio

JL Audio XDM800/8-24V Handleiding

9 Juli 2024
JL Audio

JL Audio XDM600/6-24V Handleiding

9 Juli 2024
JL Audio

JL Audio MHD600/4-24V Handleiding

9 Januari 2024
JL Audio

JL Audio MHD900/5-24V Handleiding

9 Januari 2024
JL Audio

JL Audio M800/8-24V Handleiding

9 Januari 2024
JL Audio

JL Audio MX500/1 Handleiding

6 Juni 2023
JL Audio

JL Audio XD600/6v2 Handleiding

9 Mei 2023
JL Audio

JL Audio XDM300/1 Handleiding

9 Mei 2023
JL Audio

JL Audio XDM600/1 Handleiding

7 Mei 2023
JL Audio

JL Audio XD200/2v2 Handleiding

2 Mei 2023

Handleiding Receiver

Nieuwste handleidingen voor Receiver

Henry Engineering

Henry Engineering AES DIGITAL DA 2X4 Handleiding

21 November 2024
Deaf Bonce

Deaf Bonce Machete MLA-70.2XS Handleiding

20 November 2024
QSC

QSC PowerLight 9.0 Handleiding

20 November 2024
Ashly

Ashly FX-125.4 Handleiding

20 November 2024
JBL

JBL Power P80.2 Handleiding

20 November 2024
JBL

JBL Power Px600.2 Handleiding

20 November 2024
JBL

JBL Power P-4020 Handleiding

20 November 2024
JBL

JBL Power P180.2 Handleiding

20 November 2024
JBL

JBL Power BPx1100.1 Handleiding

20 November 2024
JBL

JBL Power BPx500.1 Handleiding

20 November 2024