JL Audio JX360/4 Handleiding

JL Audio Receiver JX360/4

Lees hieronder de 📖 handleiding in het Nederlandse voor JL Audio JX360/4 (37 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/37

Thank you for purchasing a JL Audio amplifier for

your automotive sound system.

Your amplifier has been designed and manufactured to exacting

standards in order to ensure years of musical enjoyment in your vehicle.

For maximum performance, we highly recommend that you have

your new amplifier installed by an authorized JL Audio dealer. Your

authorized dealer has the training, expertise and installation equipment

to ensure optimum performance from this product. Should you

decide to install the amplifier yourself, please take the time

to read this manual thoroughly so as to familiarize yourself

with its installation requirements and setup procedures.

If you have any questions regarding the instructions in this

manual or any aspect of your amplifier’s operation, please contact your

authorized JL Audio dealer for assistance. If you need further assistance,

please call our Technical Support Department

at (954) 443-1100 during business hours.

owner’s manual

360W 4-Channel, Full-Range Amplifier

2 JL Audio

PROTECT YOUR HEARING!

We value you as a long-term customer. For

that reason, we urge you to practice restraint in

the operation of this product so as not to damage

your hearing and that of others in your vehicle.

Studies have shown that continuous exposure to

high sound pressure levels can lead to permanent

(irreparable) hearing loss. This and all other

high-power amplifiers are capable of producing

such high sound pressure levels when connected

to a speaker system. Please limit your continuous

exposure to high volume levels.

While driving, operate your audio system in

a manner that still allows you to hear necessary

noises to operate your vehicle safely (horns,

sirens, etc.).

SERIAL NUMBER

In the event that your amplifier requires

service or is ever stolen, you will need to have

a record of the product’s serial number. Please

take the time to enter that number in the space

provided below. The serial number can be found

on the bottom panel of the amplifier and on the

amplifier packaging.

Serial Number:

CH 1 & CH 2

Preamp

Input Jacks

(pg. 6)

CH 3 & CH 4

Preamp Input Jacks

(pg. 6)

Protection Status

Indicator

(pg. 11)

Power Status

Indicator

(pg. 11) High-Level

Input Jack

(pg. 6,7)

Input Mode

Selector

(pg. 7)

High-Level

Input Jack

(pg. 6,7)

Input

Sensitivity

Control

(pg. 8)

Filter Mode

Selector

(pg. 8)

Left & Right

Preamp Output Jacks

(pg. 9)

Filter

Frequency

Control

(pg. 8)

Input

Sensitivity

Control

(pg. 8)

Filter Mode

Selector

(pg. 8)

Filter

Frequency

Control

(pg. 8)

+12 VDC Ground Remote

CH. 3

(L) CH. 4

(R)

CH. 1

(L) CH. 2

(R )

BridgedBridged

Remote Turn-On

Connector

(pg. 6)

+12 V Power

Connector

(pg. 5)

Chassis Ground

Connector

(pg. 5)

CH 1 & CH 2

Speaker Outputs

(pg. 10)

CH 3 & CH 4

Speaker Outputs

(pg. 10)

4 JL Audio

product descrIptIon

The JL Audio JX360/4 is a four-channel,

full-range audio amplifier utilizing Class A/B

technology for all channels.

The JX360/4 can be operated with a wide

variety of source units and system configurations.

For detailed specifications, please refer to

Appendix B (page 13).

tYpIcal InstallatIon sequence

The following represents the sequence

for a typical amplifier installation, using an

aftermarket source unit or OEM Interface

product. Additional steps and different

procedures may be required in some applications.

If you have any questions, please contact your

authorized JL Audio dealer for assistance.

1) Disconnect the negative battery post

connection and secure the disconnected cable

to prevent accidental re-connection during

installation. This step is not optional.

2) Run 4 AWG power wire from the battery

location to the amplifier mounting location,

taking care to route it in such a way that it

will not be damaged and will not interfere

with vehicle operation. Use 2 AWG or larger

power wire and a power distribution block if

additional amplifiers are being installed with

the JX360/4.

3) Connect power wire to the positive battery

post. Fuse the wire with an appropriate fuse

block (and connectors) within 18 inches (45

cm) wire length of the positive battery post.

This fuse is essential to protect the vehicle.

Do not install the fuse until the power wire

has been securely connected to the amplifier.

4) Run signal cables and remote turn-on wire

from the source unit to the final amplifier

mounting location.

5) Run speaker cables from the speaker systems

to the amplifier mounting location.

6) Find a good, solid metal grounding point

close to the amplifier and connect the

negative power wire to it using appropriate

hardware. Use the same size power wire as the

wire connected to the “+12VDC” connection

(minimum 4 AWG), no longer than 36 inches

(90 cm) from the amplifier to the ground

connection point. In some vehicles, it may be

necessary to upgrade the battery ground wire.

(See page 5 for important notice).

Securely mount the amplifier using

appropriate hardware.

8) Connect the positive and negative power

wires to the amplifier.

9) Connect the remote turn-on wire

to the amplifier.

10) Connect the input cables to the amplifier.

11) Connect the speaker cables to the amplifier.

12) Carefully review the amplifier’s control

settings to make sure that they are set

according to the needs of the system.

13) Install the power wire fuse (50A for a

single JX360/4) and reconnect the negative

battery post terminal.

14) Turn on the source unit at a low level

to double-check that the amplifier is

configured correctly. Resist the temptation

to crank it up until you have verified the

control settings.

15) Make necessary adjustments to the input

sensitivity controls to obtain the right

overall output and the desired balance

in the system. See Appendix A (page 12)

for the recommended input sensitivity

setting method.

16) Enjoy the fruits of your labor with your

favorite music.

Product specificaties

Merk:	JL Audio
Categorie:	Receiver
Model:	JX360/4
Kleur van het product:	Zwart, zilver
Gewicht:	3450 g
Breedte:	391 mm
Diepte:	195 mm
Hoogte:	53 mm
Stroom:	50 A
Signaal/ruis-verhouding:	100 dB
Maximaal uitgangsvermogen (RMS):	320 W
Input sensitiviteit:	200 mV
Aantal versterker kanalen:	4 kanalen
RMS vermogen uitvoer per kanaal (4 Ohm):	220 W
RMS vermogen uitvoer per kanaal (2 Ohm):	320 W
Maximaal uitgangsvermogen per kanaal (4 Ohm):	280 W
Maximaal uitgangsvermogen per kanaal (2 Ohm):	360 W
Overbrugd uitgangsvermogen (max):	360 W
High-pass filterbereik:	50 - 200 Hz
Low-pass filterbereik:	50 - 200 Hz