JL Audio 1200 Handleiding
JL Audio
Auto versterker
1200
Lees hieronder de 📖 handleiding in het Nederlandse voor JL Audio 1200 (13 pagina's) in de categorie Auto versterker. Deze handleiding was nuttig voor 50 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/13
OWNER’S MANUAL
1200 W CLASS-D MONOBLOCK SUBWOOFER AMPLIFIER
1200/1v3
Thank you for purchasing a JLAudio amplifier
for your automotive sound system.
Your amplifier has been designed and manufactured to exacting
standards in order to ensure years of musical enjoyment in your
vehicle. For maximum performance and extended warranty
coverage, we highly recommend that you have your new amplifier
installed by an authorized JLAudio dealer. Your authorized
dealer has the training, expertise and installation equipment
to ensure optimum performance from this product. Should you
decide to install the amplifier yourself, please take the time
to read this manual thoroughly so as to familiarize yourself
with its installation requirements and setup procedures.
If you have any questions regarding the instructions in this
manual or any aspect of your amplifier’s operation, please
contact your authorized JLAudio dealer for assistance. If you
need further assistance, please call the JLAudio Technical
Support Department at (954) 443-1100 during business hours.
2 | JL Audio - 1200/1v3 Owner’s Manual 3
Infrasonic Filter
Defeat Switch
(pg. 10)
Preamp Output
Filter Slope
Selector
(pg. 9)
Input Sensitivity
Control
(pg. 7)
Selects Output Filter
Cutoff Frequency
(pg. 10)
Selects Infrasonic
Filter Cutoff
Frequency
(pg. 10)
Selects Low-Pass
Filter Frequency for
Amplifier Channel
(pg. 8)
Parametric EQ
"Q" (Bandwidth
Selection Control
(pg. 10)
Positive
Subwoofer
Outputs
(pg. 11)
Input Voltage
Range Selector
(pg. 7)
Preamp Output
Mode Selector
(pg. 9)
Amplifier Low-Pass
Filter Slope
Selection / Defeat
(pg. 8)
Reverses Polarity
of Amp Output
(pg. 12)
Left and Right
Preamp Output Jacks
(pg. 9)
Left and Right
Input Jacks
(pg. 7)
Bass EQ
Defeat Switch
(pg. 9)
Jack for
Remote Bass
Control Knob
(pg. 10)
Selects Low-Pass
or High-Pass Mode
for Output Filter
(pg. 10)
Remote Turn-On
Connector
(pg. 6)
Chassis Ground
Connector
(pg. 5)
+12 V Power
Connector
(pg. 5)
Parametric EQ
Center Frequency
Selection Control
(pg. 10)
Parametric EQ
Boost Control
(pg. 10)
Negative
Subwoofer
Outputs
(pg. 11)
+12VDC Ground Remote
Low/High
Cooling Efficiency Considerations:
Your JLAudio amplifier employs an
advanced type of heat management, called
RealSink™. This feature takes advantage of
convection and radiation effects to remove
heat from the amplifier circuitry. For optimum
cooling performance, the vertical heat sinks
located at the back of the amplifier should be
exposed to as large a volume of air as possible.
Enclosing the amplifier in a small, poorly
ventilated chamber can lead to excessive heat
build-up and degraded performance. If an
installation calls for an enclosure around the
amplifier, we recommend that this enclosure
be ventilated with the aid of a fan. In normal
applications, fan-cooling is not necessary, but
you still need to follow some basic guidelines:
• Amplifier mounted vertically with heat sink fins
pointing up: Optimum
• Amplifier mounted horizontally,
right side up: Good
• Amplifier mounted horizontally, but upside
down: Fair (not recommended if there is
less than 1 inch (2.5 cm) clearance above the
amplifier heat sinks)
• Amplifier mounted vertically with heat sink fins
pointing laterally: Fair
• Amplifier mounted vertically with heat sink fins
pointing down: Poor (not recommended)
If mounting the amplifier under a seat,
make sure there is at least 1 inch (2.5 cm) of
space above the amplifier’s outer shell to permit
proper cooling.
Safety Considerations:
Your amplifier needs to be installed in a dry,
well-ventilated environment and in a manner
which does not interfere with your vehicle’s safety
equipment (air bags, seat belt systems, ABS brake
systems, etc.). You should also take the time to
securely mount the amplifier using appropriate
hardware so that it does not come loose in the
event of a collision or a sudden jolt to the vehicle.
Stupid Mistakes to Avoid:
• Check before drilling any holes in your vehicle
to make sure that you will not be drilling
through a gas tank, brake line, wiring harness or
other vital vehicle system.
• Do not run system wiring outside or underneath
the vehicle. This is an extremely dangerous
practice which can result in severe damage to
your vehicle and person.
• Protect all system wires from sharp metal
edges and wear by carefully routing them,
tying them down and using grommets and
loom where appropriate.
• Do not mount the amplifier in the engine
compartment, under the vehicle, on the roof
or in any other area that will expose the
amplifier circuitry to the elements.
PROTECT YOUR HEARING!
We value you as a long-term customer. For
that reason, we urge you to practice restraint in
the operation of this product so as not to damage
your hearing and that of others in your vehicle.
Studies have shown that continuous exposure to
high sound pressure levels can lead to permanent
(irreparable) hearing loss. This and all other
high-power amplifiers are capable of producing
such high sound pressure levels when connected
to a speaker system. Please limit your continuous
exposure to high volume levels.
While driving, operate your audio system in
a manner that still allows you to hear necessary
noises to operate your vehicle safely (horns,
sirens, etc.).
SERIAL NUMBER
In the event that your amplifier requires
service or is ever stolen, you will need to
have a record of the product’s serial number.
Please take the time to enter that number in
the space provided below. The serial number
can be found on the bottom panel of the
amplifier and on the amplifier packaging.
Serial Number:
INSTALLATION APPLICATIONS
This amplifier is designed for operation in
vehicles with 12V, negative-ground electrical
systems. Use of this product in vehicles with
positive ground and/or voltages other than 12V
may result in damage to the product and will void
the warranty.
This product is not certified or approved for
use in aircraft.
Do not attempt to “bridge” the outputs of this
amplifier with the outputs of a second amplifier,
including an identical one.
PLANNING YOUR INSTALLATION
It is important that you take the time to read
this manual and that you plan out your
installation carefully. The following are some
considerations that you must take into account
when planning your installation.
4 | JL Audio - 1200/1v3 Owner’s Manual 5
POWER CONNECTIONS
Before installing the amplifier,
disconnect the negative (ground) wire
from the vehicle’s battery. This will prevent
accidental damage to the system, the vehicle
and your person during installation.
+12VDC Ground Remote
Preamp Output Section Infrasonic Filter “Q” Center Freq. Boost (dB) Amp LP Filter
Advanced
Bass
Control
Amplifier Input Section Subwoofer Output
MONO OUTPUT ONLY
Left Output Right Output Left Ch. Right Ch.Filter Freq. (Hz) Filter Freq. (Hz)Infrasonic Freq. (Hz) Remote Bass Port
Full Range | Amp Filter | Out Filter
Output Mode Filter Slope Mode Mode | Slope Input Voltage Input Sens.
Output Polarity
12dB | 24dB
Filter Mode
LP | HP
Bass EQ
Off | On
Off | 12dB | 24dB Low | High
Normal|Reversed
Off | On
40
45
55
65
85
120
200 15
18
25
30
40
50
60 40
45
55
65
80
100
200
0.5
0.7
1.1
1.6
2.7
4.3 20
25
35
45
55
70
80 0
+4
+10
+13
+15
120 0 /1v3
Monoblock Subwoofer Amplifier
+12V Battery Connection
You will need to connect a power wire to
the vehicle’s positive battery terminal, using an
appropriate power ring or specialized battery
terminal connector, such as the JLAudio
XB-BTU or XD-BTS. This connection must
be tight and corrosion-free to ensure proper
connectivity. This wire MUST be fused
appropriately for safety. Any power wires run
through metal barriers (such as firewalls), must
be protected with a high quality insulating
grommet to prevent damage to the insulation
of the wire. Failure to do so may result in a
dangerous short circuit.
Power Wire Requirements
The 1200/1v3’s “+12 VDC” and “Ground”
connections are designed to accept 4 AWG
power wire. 2 AWG or 1/0 AWG pure copper
wire is recommended for any power wire run
longer than 72 inches (180 cm). This larger
wire should be reduced to 4 AWG using a
distribution block within 36 wire inches (90
cm) of the amplifier’s “+12 VDC” connector.
For runs shorter than 72 inches, 4 AWG
pure copper power wire is acceptable.
If you are installing the 1200/1v3 with other
amplifiers and wish to use a single main power
wire, use 1/0 AWG pure copper wire as a main
power wire. This 1/0 AWG power wire should
terminate into a fused distribution block mounted
as close to the amplifiers as possible and should
connect to the 1200/1v3 with 4 AWG pure copper
power wire.
Please note that lower AWG numbers mean
bigger wire and vice-versa (1/0 AWG is the largest,
2 AWG is smaller, then 4 AWG, then 8 AWG, etc.).
IMPORTANT
!
We do not recommend the use of “copper-
clad aluminum wire” or “CCA” wire because
this wire is significantly less conductive than
pure copper wire. Only use pure copper power
wire, such as JLAudio’s Premium Power Wire.
Tinned copper wire (silver color) is acceptable
as the tin-plating is only a very minor
component of the wire.
Fuse Requirements
The installation of a fuse on the main power
wire, within 18 wire inches (45 cm) of the positive
battery terminal is vital to protect the wire and
the vehicle from fire in the event of a collision
or short-circuit. The fuse value at each power
wire should be just high enough for all of the
equipment being run from that power wire. Do
not use a fuse with a value that far exceeds the
total fuse rating of the electronics connected to
the wire.
If only the 1200/1v3 is being run from that
power wire, we recommend a 100A fuse be
used. MaxiFuse™ (big plastic-body fuse) or ANL
(large blade-type) fuses are recommended.
If other amplifiers are also being powered
from a main power wire and all the amplifiers
together exceed 100 amps in total fuse rating,
we recommend the use of an ANL (large-blade)
fuse and holder at the battery plus a fused
distribution block near the amplifiers. Each
amplifier must be fused independently at the
outputs of the fused power distribution block.
We recommend appropriately rated MaxiFuse™
fuses and a JLAudio fused distribution block.
Please consult with your JLAudio
dealer to make sure that the wire, fuse
holder and fuse ratings are appropriate
for your system’s needs. The safety of
your installation depends on appropriate
power connections and fuse protection.
PRODUCT DESCRIPTION
The JLAudio 1200/1v3 is a monoblock
subwoofer amplifier utilizing proprietary and
patented Class D technology. Its frequency
response is limited to the range below 250 Hz. It
is not designed for driving midrange speakers or
tweeters. Every aspect of its operation has been
optimized for low-frequency amplification.
For detailed specifications, please refer to
Appendix B (page 15).
TYPICAL INSTALLATION SEQUENCE
The following represents the sequence for
a typical amplifier installation, using an
aftermarket source unit or OEM Interface
processor (like the CleanSweep® CL441dsp).
Additional steps and different procedures may
be required in some applications. If you have
any questions, please contact your authorized
JL Audio dealer for assistance.
1) Disconnect the negative battery post
connection and secure the disconnected cable
to prevent accidental re-connection during
installation. This step is not optional!
2) Run power wire from the battery location to
the amplifier mounting location, taking care
to route it in such a way that it will not be
damaged and will not interfere with vehicle
operation. 2 AWG or larger is recommended
for wire runs greater than 72 inches (180
cm) in length. This 2 AWG wire needs
to be reduced to 4 AWG within 36 wire
inches of the amplifier using a distribution
block. Use a 1/0 AWG or 1/0 AWG main
power wire with a fused power distribution
block when additional amplifiers are being
installed with the 1200/1v3 and are being
powered from the same main power wire.
3) Connect power wire to the positive battery
post. Fuse the wire with an appropriate fuse
block (and connectors) within 18 inches (45
cm) wire length of the positive battery post.
This fuse is essential to protect the vehicle.
Do not install the fuse until the power wire
has been connected to the amplifier.
4) Run signal cables (RCA cables) and remote
turn-on wire from the source unit or interface
processor to the amplifier mounting location.
5) Run speaker wire from the speaker systems to
the amplifier mounting location.
6) Find a good, solid, bare metal grounding
point close to the amplifier and connect the
negative power wire to it using appropriate
hardware. Use minimum 4 AWG power wire,
no longer than 36 inches (90 cm). In some
vehicles, it may be necessary to upgrade the
battery’s ground wire as well. (See page 6 for
important notice).
7) Securely mount the amplifier using
appropriate hardware.
8) Connect the remote turn-on wire and the
positive and negative power wires to the
amplifier’s power connector plug. Then insert
the power connector plug into the amplifier’s
power connector receptacle, pushing firmly.
9) Connect the RCA input cables
to the amplifier.
10) Connect the speaker wires to the speaker
connector plug and insert the plug firmly into
the speaker connector receptacle.
11) Carefully review the amplifier’s control
settings to make sure that they are set
according to the needs of the system.
12) Install power wire fuse (100A for a
single 1200/1v3) and reconnect the negative
battery post terminal.
13) Turn on the source unit at a low level
to double-check that the amplifier is
configured correctly. Resist the temptation
to crank it up until you have verified the
control settings.
14) Make necessary adjustments to the input
sensitivity controls to obtain the right
overall output and the desired balance
in the system. See Appendix A (pages 14)
for the recommended input sensitivity
setting method.
15) Enjoy the fruits of your labor with your
favorite music.
Product specificaties
| Merk: | JL Audio |
| Categorie: | Auto versterker |
| Model: | 1200 |
Heb je hulp nodig?
Als je hulp nodig hebt met JL Audio 1200 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Auto versterker JL Audio
24 Juni 2023
24 Juni 2023
24 Juni 2023
24 Juni 2023
24 Juni 2023
24 Juni 2023
24 Juni 2023
24 Juni 2023
24 Juni 2023
24 Juni 2023
Handleiding Auto versterker
- Auto versterker JVC
- Auto versterker Kenwood
- Auto versterker Pioneer
- Auto versterker Auna
- Auto versterker Autotek
- Auto versterker Hifonics
- Auto versterker Macrom
- Auto versterker Marquant
- Auto versterker Phoenix Gold
Nieuwste handleidingen voor Auto versterker
19 Oktober 2023
19 Oktober 2023
19 Oktober 2023
19 Oktober 2023
19 Oktober 2023
19 Oktober 2023
19 Oktober 2023
19 Oktober 2023
19 Oktober 2023
19 Oktober 2023