Jensen XDA94RB Handleiding

Jensen Niet gecategoriseerd XDA94RB

Lees hieronder de 📖 handleiding in het Nederlandse voor Jensen XDA94RB (18 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 63 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/18

INSTALLATION / OWNER’S MANUAL

XDA91RB, 92RB, 94RB

XDA SERIES

Preparation

Please read entire manual before installation. Due to the technical nature

of amplifiers, it is highly recommended that your amplifier is installed by a

professional installer or an authorized dealer.

Before You Start

• Disconnect negative battery terminal. (consult a qualified technician for

instructions)

• Avoid installing the amplifier where it would be subject to high temperatures, such

as from direct sunlight, or where it would be subject to dust, dirt or excessive

vibration.

• Use extreme caution when drilling holes to avoid damaging fuel lines or existing

vehicle wiring.

• All amplifier installations require power, signal and speaker wires (not included).

• An amplifier installation kit (sold separately) is highly recommended to facilitate

the installation. Consult your dealer for recommendations.

Mounting Location

• Choose a mounting location for the amplifier. Suggested locations include under a

seat or in the trunk.

• The amplifier can be mounted horizontal (recommended) or vertical. For optimum

performance, make sure to provide at least 1" of space around all sides. Do not

mount the amplifier under carpets or where airflow is restricted.

• Do not install the amplifier where it may be exposed to moisture.

• The optimum mounting location varies between vehicles. Remember to test all

amplifier functions before completing the final mounting procedure.

TYPICAL

MOUNTING

METHOD

XDA SERIES

NOTE:

Be sure to follow specific instructions included with your amplifier installation kit

(not included with this amplifier). The information below should be used as a general

guideline only.

Power Wire (+12V)

• Disconnect negative battery terminal before proceeding. Consult a qualified

technician for instructions if you are unsure.

• Plan wire routing before cutting any wires to length. Begin by routing the power

+12V wire from the battery to the amplifier location. Use a grommet when running

wires through the firewall or metal openings. Avoid running the power wire near

existing vehicle wiring to prevent induced noise from entering the audio system.

• Use extreme caution when drilling holes to avoid damaging fuel lines or existing

vehicle wiring.

• The +12V wire MUST be fused within 18" of the battery for protection of the vehicle’s

electrical system.

Ground Wire (GND)

• The amplifier ground wire should be as short as possible (no more than 36" or

1 meter). Choose a clean unpainted section of metal or the vehicle chassis when

attaching the ground connection. Be sure to clean the area of any dirt or grease.

Remote Turn-on Wire (REM)

• The remote turn-on wire connects to the head unit's amplifier turn-on lead or

power antenna output.

Speaker Wires

• Choose adequate gauge speaker wire depending on your exact amplifier/speaker

combination. Be sure to observe polarity when connecting.

• Do not ground any speaker wires or connect any speaker wires together.

Input Signal

• The amplifier's input signal connects to the head unit's low level (RCA) or high level

(speaker wire) outputs.

• Low level input signals deliver the best performance. If unavailable, use the high

level inputs - when interfacing with factory head unit for instance.

Power / Protect Indicators

• Colored LED indicators illuminate from the plastic power terminal.

• The blue LED illuminates during normal operation ( ) and the red POWER

LED indicator is visible when the amplifier detects a fault ( ).PROTECT

CAUTION

• Do not use both low and high level inputs at the same time. Connect only one or the

other.

• Keep low level inputs away from any power wires to avoid engine noise.

• Never run any wires underneath or outside the vehicle.

Connection Descriptions

Product specificaties

Merk:	Jensen
Categorie:	Niet gecategoriseerd
Model:	XDA94RB

Heb je hulp nodig?

Als je hulp nodig hebt met Jensen XDA94RB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Jensen

Jensen CAR701-4 Handleiding

24 Oktober 2024

Jensen JC7DM Handleiding

8 December 2023

Jensen CD4720 Handleiding

11 Juni 2023

Jensen VM9116 Handleiding

16 Mei 2023

Jensen VM9224 Handleiding

10 Mei 2023

Jensen VM9115 Handleiding

7 Mei 2023

Jensen SD1411 Handleiding

24 April 2023

Jensen UV10 Handleiding

14 April 2023

Jensen CD2610 Handleiding

2 April 2023

Jensen CD6112 Handleiding

25 Maart 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Electrolux STA9 Handleiding

23 November 2024

Electrolux UMP3 Handleiding

23 November 2024

Electrolux ZS70GL Handleiding

23 November 2024

Bosch HEZ8TK36UC Handleiding

23 November 2024

Bosch HEZ8ZZ36UC Handleiding

23 November 2024

Bosch HDZIT301 Handleiding

23 November 2024

Bosch HEZBS301 Handleiding

23 November 2024

LG LX-330 Handleiding

23 November 2024

Stamos S-PLASMA 60U Handleiding

23 November 2024

Bosch KSZ2AVU00 Handleiding

22 November 2024