Jensen VX7071 Handleiding

Jensen Navigator VX7071

Lees hieronder de πŸ“– handleiding in het Nederlandse voor Jensen VX7071 (4 pagina's) in de categorie Navigator. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
What s in the Box’
The following items are supplied
with the VX702 :1
β€’ VX702 Head Unit1
β€’ Trim Ring
β€’ Hardware
β€’ Power/Speaker Output Harness
β€’ Remote Control
β€’ External Microphone
β€’ GPS Antenna
β€’ Installation Guide
Tools and Supplies
The following tools and supplies
are needed to install the head unit:
β€’ Torx type, ξ˜‚ at-head and Philips
screwdrivers
β€’ Wire cutters and strippers
β€’ Tools to remove existing radio (screw
driver, socket wrench set or other
tools)
β€’ Electrical tape
β€’ Crimping tool
β€’ Volt meter/test light
β€’ Crimp connections
β€’ 18 gauge wire for power connections
β€’ 16 – 18 gauge speaker wire
VX7021
Installation / Quick Start Guide
Complete operation manuals are
online at www.jensenmobile.com
Note: There is no operation manual in this package
2
Disconnect the Battery
β€’ To prevent a short circuit, be sure t the ignition and remove the negative (-) battery cable prior to installation. o turn off
NOTE: If
the is to installed in a car head unit be equipped with an on-board drive or navigation computer, do not disconnect the
battery cable conditions, cable. If the is disconnected, computer memory may be lost. Under these the use extra
caution during installation to avoid causing a short circuit.
Replacing the Fuse
β€’ When replacing the vehicles adio fuse always use the proper rated replacement fuse. Using a fuse with an improper ratingr
could damage the unit and cause a fi re.
ISO-DIN Installation
The is designed to t into a 2.0 DIN dashboard opening. The unit has threaded holes in the chassis side panels which may head unit fi
be used with the original factory mounting brackets of some oyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to T
mount the radio to the dashboard. Please consult with your local car stereo specialty shop for assistance on this type of
installation.
NOTE: It is the end-users responsibility to install and operate this unit in a manner in accordance with local, state and federal
laws. The PARKING BRAKE wire MUST BE CONNECTED as directed in the manual.
Using the Cosmetic Trim Ring
A cosmetic trim ring is supplied with the head unit for installation
ξ˜‚ exibility. This unit will ξ˜„ t into most import dashes with little or no
modiξ˜„ cation to the dash board/cavity. Some US domestic vehicle
dashes will accept a Double-DIN chassis, but there is usually a
small gap between the radio and dash piece after installation is
complete. In this case, use the trim ring to conceal any gaps that
may be present.
1. Remove the existing factory radio from the dashboard or
center console mounting. Save all hardware and brackets as
they will be used to mount the new radio.
2. Remove the factory mounting brackets and hardware from the
existing radio and attach them to the new radio.
CAUTION! Do not exceed M5 X 6MM screw size. Longer
screws may damage components inside the chassis.
3. Place the radio in front of the dashboard opening so the wiring
can be brought through the . Follow thedash opening
wiring diagram carefully and make certain all connections are
secure and insulated with wire nuts or electrical tape. After
completing the wiring connections, plug the connector into
the mating socket on the rear of the chassis Turn the. unit
ON to confi rm operation (vehicle ignition switch must be
β€œON”). If the unit does not operate, re-check all wiring until the
problem is corrected.
4. Mount the new radio assembly to the dashboard or center
console using the reverse procedure in step 1 above.
CAUTION! Be careful not to damage the car wiring.
NOTE: For proper operation of the CD/DVD player, the chassis must be mounted within 30Β° of horizontal. Make sure the
unit is mounted within this limitation.
The recommended Interface SWC is the PAC control adapter SWI-RC steering wheel .
SWI-RC installation hints:
1. Set "Radio Select Switch" et the SWI-RC to position 7 Pioneer/Sony/Other .. S - " "
2. " "Programming - Use the Other radio function mapping order for Jensen branded head units.
3. When programming the SWI-RC, if a function is not supported (or not desired), then the function be skipped as perMUST
the PAC SWI-RC instructions.
4. The SWC functions also be programmed in the correct order per the PAC SWI-RC radio function mapping orderMUST
instructions.
S W C Readyteering heel ontrol (SWC)
Wiring Diagram
CAUTION! IMPORTANT: Incorrect wiring connections can damage the unit. Follow the wiring instructions
carefully, or have the installation handled by an experienced technician.
Need Help? For technical assistance, call the Jensen customer support line at 1-8 .88-921-4088
Note: Some vehicles may not support all SWC functions. Professional Installation is recommended.
3
RIGHT FRONT SPEAKER (-)
RIGHT REAR SPEAKER (+)
RIGHT REAR SPEAKER (-)
LEFT REAR SPEAKER (+)
LEFT REAR SPEAKER (-)
BATTERY 12V (+)
GROUND (-)
ACC / IGNITION (+)
TFT DIMMER (+)
POWER ANTENNA / AMP (+)
PARKING BRAKE (-)
REVERSE (+)
3.5mm FEMALE CONN.
LEFT FRONT SPEAKER (+)
BLACK
YELLOW
RED
PINK
GREEN/WHITE
BLUE
GRAY/BLACK
GRAY
GREEN/BLACK
GREEN
PURPLE/BLACK
ORANGE
PURPLE
SWC
WHITE/BLACK
WHITE
LEFT FRONT SPEAKER ( )-
RIGHT FRONT SPEAKER ( )+
Yellow RCA - Rear Camera In
SiriusXMBlack DIN Cable -
Black Female 3.5mm - BT Microphone
Black 1mm Wire - BT Antenna


Product specificaties

Merk: Jensen
Categorie: Navigator
Model: VX7071

Heb je hulp nodig?

Als je hulp nodig hebt met Jensen VX7071 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Navigator Jensen

Handleiding Navigator

Nieuwste handleidingen voor Navigator