JBL MS-A5001 Handleiding

JBL Receiver MS-A5001

Lees hieronder de 📖 handleiding in het Nederlandse voor JBL MS-A5001 (14 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/14

User GUide

Ms-A5001

Digital signal processing ampliﬁer

123 4





 





  





40 A

2X40A

2 x 40A

1 x 80A





















  









9 10

1 Input-Level Control

This control is used to match

the input sensitivity to the signal

voltage for proper analog-to-

digital conversion. See page 7 for

details. DO NOT use this control

to set the relative output level of

amplifier channels!

2 Input Signal Selector

Lo/Hi/Hi2 sets input voltage and

impedance range. See page 7 for

details.

Audio Inputs

Use RCA audio cables for

preamp-level connections or

attach the included RCA to bare

wire adapters for speaker-level

input connections.

Pass-Through Outputs

Input channel 1 sends signals to

Output 1. Input channel 2 sends

signals to Output 2. The

MS-A5001’s filter settings do not

affect these channels.

5 Onboard Fuses

2 x 40A ATC type.

Display Panel

Displays the amplifier’s settings.

User Controls

These controls allow you to adjust

the amplifier’s settings. See page

9 for details.

8 +12V Power Input

Connects to your vehicle’s battery

with a 80A fuse within 18 inches

(45.7cm) of the battery’s positive

terminal.

9 Remote Turn-On Input

Connects switched +5V to

+12V. Note: The MS-A5001 also

includes signal-sensing turn-on.

You may choose the turn-on

method during setup. See pages

5 and 9-10 for details.

10 Chassis Ground Input

Connect to a paint-free spot on

the vehicle chassis.

Speaker Outputs

Two mono speaker outputs.

These outputs send the same

output signal (in parallel) for

the added convenience of

connecting multiple subwoof-

ers. Be sure to account for

parallel resistance connections

when you determine the load on

the MS-A5001’s output. Do not

connect loads below a total of

two ohms.

Ms-A5001 FeATUres

FCC REGULATIONS

Caution:

Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user's authority to

operate the equipment.

Compliance statement:

1: This device is veriﬁed to comply with Part 15 of the FCC Rules. Operation subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

2: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not

occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

•

Ms-A5001

diGiTAL siGNAL-PrOCessiNG AMPLiFier

PLeAse reAd THis BeFOre YOU BeGiN!

JBL® MS-series amplifiers include many features not found on conventional car-audio amplifiers. As a result, the setup

procedure for JBL MS-series amplifiers is different from that of conventional car-audio amplifiers. The following

overview of features and functions will help you plan a great system and make the best use of the MS-A5001’s

innovative features.

About the digital signal processing (DSP) included in MS-series amplifiers:

All of the signal processing in MS-series amplifiers is digital. Digital signal processing, along with the amplifiers’ intuitive

controls and display, make precise setup easy. Only the input-level controls are analog.

Will I lose my settings if I disconnect the amplifier or the car’s battery?

No. The MS-A5001 stores all of the DSP settings in nonvolatile memory, so you will not lose any settings if power

is removed.

Why are the input-level controls analog?

In order to provide the best signal-to-noise ratio and to maximize the resolution of the digital-to-analog conversion,

the maximum input-signal level to the analog-to-digital (A/D) converters must be precisely set. The control that sets

the level must be an analog control. The included setup CD and the procedure described in this manual make setting

the level simple and precise. Once you set the input-level control, do not use the control to “tune” the system. Use the

digital output-level control to adjust the relative level between amplifier channels to tune the system.

Product specificaties

Merk:	JBL
Categorie:	Receiver
Model:	MS-A5001
Kleur van het product:	Black, White
Ingebouwd display:	Ja
Gewicht:	2500 g
Breedte:	210 mm
Diepte:	70 mm
Hoogte:	183 mm
Connectiviteitstechnologie:	Bedraad
DC voltage input:	12 V
Bedoeld voor:	Auto
Audio-uitgangskanalen:	1.0 kanalen
Frequentiebereik:	20 - 270 Hz
Signaal/ruis-verhouding:	106 dB
Totale harmonische vervorming (THD):	- procent
Input sensitiviteit:	100 mV
Piekvermogen per kanaal:	- W
Speakers connectiviteit type:	RCA
RMS vermogen uitvoer per kanaal (4 Ohm):	500 W
RMS vermogen uitvoer per kanaal (2 Ohm):	500 W