JBL LSR708i Handleiding

JBL Monitor LSR708i

Lees hieronder de πŸ“– handleiding in het Nederlandse voor JBL LSR708i (10 pagina's) in de categorie Monitor. Deze handleiding was nuttig voor 53 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/10
Set Up Instructions
7 Series β€œi” Set Up Instructions

7 Models 2SeriesInstalled SetUpPage  8/1/16 
In preparation for set up you will need:
ο‚· One of more JBL 7 Series β€œi” model speakers
ο‚· A recommended Harman Crown Power Amplifier
OR Harman BSS Soudweb London processor AND an amplifier with suitable power
ο‚· Mounting hardware
ο‚· Speaker Wire
ο‚· Balanced line level input cables
ο‚· Female XLR to β€œphoenix” adaptors if needed
ο‚· A computer with Windows 7 operating system and to which you have administrative privileges and access to the
internet and HiQnet Audio Architect Software installed or London Architect Software installed.
ο‚· Category 5e Cable
ο‚· An Ethernet switch if more than one Crown DCi power amplifier is used.
ο‚· Small flat Head screwdriver
ο‚· Phillips screwdriver
Support:
JBL Customer Support is available Monday through Friday 8:00am - 5:00pm Pacific Coast Time in the U.S.A.
+1 (800.852.5776), www.jblproservice.com
Audio Architect Software with Crown Amplifiers, please contact Crown Customer Support at +1 (800) 342-6939
Monday through Thursday 9:00am - 7:00pm, Friday: 9:00am - 5:00pm Eastern Standard Time in the U.S.A.
www.crownaudio.com/techsupport
London Architect Software with BSS Soundweb London processors, please contact BSS Customer Support at +1
(800) 931-2357 during the hours of 8:00am - 5:00pm Mountain Time in the U.S.A www.bssaudio.com/en-US/support
Outside the USA: Contact the HARMAN Professional Distributor in your area. A complete list of HARMAN
international distributors is provided on our U.S.A. website: www.jblpro.com
Installation and Mounting of Speakers
7 Series β€œi” model enclosures are reinforced to allow safe mounting and include mounting points on the top,
bottom and rear panel of the speaker. Speaker dimensional drawings, location of mounting points, and
mounting hardware requirements can be found at the end of this document, The speakers can be installed
using readily available mounting brackets. A range of brackets are available from Adaptive Technologies
Group 1635 E. Burnette Street, Signal Hill, California, USA 90755 Telephone: +1 (562) 273-4239 
design@adapttechgroup.comwww.adapttechgroup.com Bracket models can be found at the end of this
document.
Caution: When installing speakers, observe safe mounting practices and recommendations provided by
mounting hardware manufacturer. Do not modify the speaker enclosure.
Amplifier and Power Requirements
The 708i and 705i models require use of an external power amplifier capable of delivering 300 watts per channel and
also Harman Professional digital signal processing. The following Harman Crown Audio power amplifiers include the
required Harman Digital Signal Processing and are recommended:
7 Series β€œi” Set Up Instructions

7 Models 3SeriesInstalled SetUpPage  8/1/16 
β€’ DCi 2|300N 2 channel power amplifier
β€’ DCi 4|300N 4 channel power amplifier
β€’ DCi 8|300N 8 channel power amplifier
A DCi 8|300 power amplifier supplies power for up to eight speakers,
or up to four bi-amplified speakers or any combination of single and
bi-amplified speakers. A detailed owner’s manual can be downloaded
at www.crownaudio.com Crown DCi β€œN” networked models include
the required digital signal processing for 7 Series speaker tuning
profiles and also additional filters that can be used as room eq.
Additionally, these amplifiers accept digital signals via HARMAN BLU
link audio protocol. If you wish to use an amplifier other than the
Crown DCi Networked models specified above, you must also use a
HARMAN BSS Soundwebβ„’ London Signal Processor. Information
about BSS Soundweb London Processors and accessories is
available at www.bssaudio.com
The Crown DCi models incorporate internal fans that are engaged full-
time ensure the operating temperature of the power amp does not
exceed specified thermal conditions. It is preferable to locate power
amplifiers outside the listening area.
Connections and Wiring
Speaker Inputs:
The 708i and 705i can be powered using a single amplifier channel or bi-amplified using separate amplifier channels
for the low frequency and high frequency drivers. The speakers are supplied with β€œphoenix” type Euro-block wiring
plugs installed. Remove and connect speaker wire to EITHER the plug inserted in the connector labeled Single Wire
OR the plug inserted in the connector labeled Bi-Amplified. When operating the speaker using the Single Wire
connection, the supplied plug must remain inserted in the Bi-Amplified connector. Removing this plug will prevent
single wire operation. Replacement plugs can be obtained by contacting JBL Customer Service at
www.jblpro.com/support.
Dedicated DSP device files are required for single wire and bi-amplified operation. These are available for download
at www.jblpro.com/7series.
The speakers should be connected to the power amplifier using two conductor speaker wire. We recommend the
use of high quality 12-gauge oxygen-free copper stranded wire, readily available from electronics retailers. Using 12-
gauge wire, the speaker can be placed up to 100 feet from the power amplifier.
Crown Amplifier Inputs
Signal sources should be connected to Crown power amplifiers using
balanced line level cables. Crown Power amplifiers feature balanced
analog inputs using β€œphoenix” type connectors. For use with XLR,
balanced ¼” TRS and other connectors, adaptors should be used.
Crown recommends using pre-built or professionally wired balanced
cables (two-conductor plus shield). Balanced wiring provides better
rejection of unwanted noise and hum; however, unbalanced line may
also be used. Use 6-pin plug-in cable ends at the amp input connectors.
A male connector is supplied for each input of your model of amplifier.
Additional connectors are available from Crown (P/N 5024623). Figure
3 shows connector pin assignments for balanced wiring and Figure 4


Product specificaties

Merk: JBL
Categorie: Monitor
Model: LSR708i

Heb je hulp nodig?

Als je hulp nodig hebt met JBL LSR708i stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Monitor JBL

Handleiding Monitor

Nieuwste handleidingen voor Monitor