JBL GT5-A604 Handleiding

JBL Receiver GT5-A604

Lees hieronder de 📖 handleiding in het Nederlandse voor JBL GT5-A604 (4 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 6 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

GT5-A604

OWNER’S MANUAL

A B C D E F

2-1/8"

54mm

9-1/4"

235mm

12"

305mm

2x4x 1x

Installation Warnings and Tips

• Disconnect the negative (–) lead from your vehicle’s

battery.

• At the installation sites, locate and make a note of

all fuel lines, hydraulic brake lines, vacuum lines

and electrical wiring. Use extreme caution when

cutting or drilling in and around these areas.

• Choose a safe mounting location away from moisture.

• Make sure there is sufficient air circulation at the

mounting location for the amplifier to cool itself.

• Mount the amplifier, using the supplied hardware.

Specifications

• 60W RMS x 4 @ 4 ohms and 1% THD + N*≤

• 80W RMS x 4 @ 2 ohms, 14.4V supply and

≤1% THD + N*

• 160W RMS x 2 @ 4 ohms, 14.4V supply and

≤1% THD + N*

• Total peak power: 640 watts

• Frequency response: 10Hz – 100kHz (–3dB)*

• Maximum input signal: 6V*

• Maximum sensitivity: 200mV*

• THD + N: 0.05%

• Signal-to-noise ratio: 85dBA

(reference 1W into 4 ohms)*

• Signal-to-noise ratio: 102dBA

(reference rated power into 4 ohms)

* CEA-2006A-compliant

0Speaker Output Connectors

• Connect the speakers to these terminals,

observing proper polarity:

• Four-channel operation: Connect the front

left speaker to the Front L+ and L– terminals,

and the front right speaker to the Front R+ and

R– terminals. Repeat for rear speakers, using

the Rear L+ and L– terminals, and the Rear R+

and R– terminals.

• Three-channel operation: Connect the stereo

speakers to the Front terminals, as above.

Connect the single speaker into which the

amplifier’s rear channels will be bridged to the

Rear R+ and Rear L– terminals.

• Two-channel (bridged) operation: Connect one

speaker to the Front R+ and Front L– termi-

nals. Connect the other speaker to the Rear

R+ and Rear L– terminals.

• Minimum speaker impedance for stereo opera-

tion is 2 ohms. Minimum speaker impedance for

bridged operation is 4 ohms.

1Fuses

• Replace only with the same type and rating.

2Power Input Connectors

• +12V: Connect to the positive terminal of the

vehicle’s battery. 8 AWG wire is recommended.

Install an appropriate fuse holder and fuse (40A

minimum) within 18 inches of the battery. Make

sure the wire is not damaged or pinched during

installation. Install protective grommets when

routing wires through the firewall or other sheet

metal.

• GND: Connect to the vehicle’s chassis. Refer to

the picture below.

• REM: Connect to the “Remote Out” lead from

the source unit or to a source of switched

12V+ (ACC).

3Aux Output Connectors (RCA)

• Summed, nonfiltered pass-through output.

Front right and rear right inputs are combined

and sent to the right AUX output. Front left

and rear left inputs are combined and sent

to the left AUX output. Connect to the input

of an additional subwoofer amplifier.

4Front Input Connectors (RCA)

• Connect to the front RCA outputs from the

source unit or signal processor.

5Front Input-Level Control

• Used to match the front input level of the

amplifier to the output level of the source unit.

• See Ffor the adjustment procedure.

6Front Crossover-Frequency Control

• 12dB/octave crossover, variable from

32Hz to 320Hz.

• See Gfor the adjustment procedure.

7Front Crossover-Filter Selector

• LP: Select for subwoofer(s).

• FLAT: Select for full-range speakers when

no subwoofer will be used in the system.

• HP: Select for midrange speakers or

full-range speakers when a subwoofer is

used in the system.

8Power On LED

• Illuminated when the amplifier is on.

9Protect LED

• Illuminated under any of the following fault

conditions: battery over/under voltage, short

circuit in speaker wires, amplifier is too hot,

amplifier’s output circuit has failed (DC voltage

present in the amplifier’s output).

ARear Bass-Boost Control

• Provides up to 6dB of boost at 50Hz. Set

the Bass-Boost control according to your

preference, being careful not to apply enough

boost to damage the speaker(s).

BRear Crossover-Frequency Control

• 12dB/octave crossover, variable from

32Hz to 320Hz.

• See adjustment procedure in G.

CRear Crossover-Filter Selector

• LP: Select for subwoofer(s).

• FLAT: Select for full-range speakers when

no subwoofer will be used in the system.

• HP: Select for midrange speakers or

full-range speakers when a subwoofer is

used in the system.

DRear Input-Level Control

• Used to match the rear input level of the

amplifier to the output level of the source unit.

• See Ffor the adjustment procedure.

ERear Input Connectors (RCA)

• Connect to rear RCA outputs from the source

unit or signal processor.

FSetting Input Level

ATurn all Input-Level controls counterclockwise

to 6V (minimum).

BWith a dynamic music track playing, turn head

unit’s volume control to the 3/4 position.

CTurn Front Input-Level control clockwise until

the music is so loud that it no longer sounds

clear (distortion is present in the output).

DTurn Front-Input-Level control counterclock-

wise gradually, just until the music sounds

clear, once again.

EFront-level input is now adjusted correctly

FAdjust Rear Input-Level control so that the

level of the rear speakers is proportionate to

the level of the front speakers, according to

your preference.

GSetting the Crossover

ACrossover setting for 5" or larger full-range

speakers when no subwoofer is included in

the system.

BCrossover setting for midrange and/or

full-range speakers when a subwoofer

is included in the system.

CCrossover setting for subwoofers.

Note: Acceptable frequency ranges indicated

in gray.

GT5-A604 CAR AUDIO POWER AMPLIFIER OWNER’S MANUAL

Factory Bolt Ring Connector

Ground Wire

Note: Remove any paint

below ring connector.

Star Washer

This product is designed for mobile applications and is not

intended for connection to the mains.

A valid serial number is required for warranty coverage.

Features, specifications and appearance are subject to change

without notice.

Product specificaties

Merk:	JBL
Categorie:	Receiver
Model:	GT5-A604
Kleur van het product:	Zwart
Gemiddeld vermogen:	320 W
Uitgangsvermogen:	640 W
Signaal/ruis-verhouding:	85 dB
Afmetingen (B x D x H):	235 x 54 x 305 mm