JBL DSP4086 Handleiding

JBL Receiver DSP4086

Lees hieronder de ๐Ÿ“– handleiding in het Nederlandse voor JBL DSP4086 (10 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/10
JBL DSP Ampli๏ฌer DSP4086
EN
FR
ZH-CH
ID
JP
KO
RU
ES
Owner's Manual
Manual de propietario
Mode dโ€™emploi
ษŠษญษคษจษœษจษžษซษฌษœษจ๎€ƒษฉษจษฅษถษกษจษœษšษฌษŸษฅษน
ๆฌฝไจชไฉ›โฑƒ
Panduan Pengguna
ใ€Šไช”้“กๅƒ‡ๅ‰…
์นบํ‘ทํ•ž๏˜“์ปฒ์ก“์ปช
EN
1
THANK YOU FOR YOUR PURCHASE . . .
Your product has been designed to provide you the performance and ease of operation you expect from JBL. Take time
to read this manual before operating or installing your ampli๏ฌer. This manual describes general installation guidelines and
operation instructions. Please note that proper installation of mobile audio components requires quali๏ฌed experience with
mechanical and electrical procedures. If you do not have the knowledge and tools to perform this installation, we strongly
recommend consulting an authorized JBL dealer about your installation options.
TABLE OF CONTENTS
PRODUCT DESCRIPTION
ยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยท
2
WHAT'S IN THE BOX
ยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยท
2
INSTALLATION AND WIRING
ยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยท
2
SETTING THE SOUND
ยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยท
4
SPECIFICATIONS
ยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยท
6
TROUBLESHOOTING
ยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยท
6
EN
EN
JBL DSP Ampli๏ฌer DSP4086
2
Power and Ground Connections
โ€ข Connect the power wire to the positive terminal Power: +12V
of the vehicleโ€™s battery. Make sure the fuse and fuse holder are
within 18โ€ (457mm) of the battery.
โ€ข Connect the wire to the negative terminal of Ground: GND
the vehicleโ€™s battery, or to the vehicleโ€™s chassis near the battery
with a screw. If possible, remove any paint from the NOTE:
chassis for best contact. It is recommended to use a star
washer below the ring connector for a secure connection.
โ€ข Connect the remote turn-on wire to the โ€œRemote Remote-In:
Outโ€ lead of the source unit, if using low-level signal inputs with
an aftermarket stereo. If you are using high-level signal NOTE:
inputs (your vehicleโ€™s speaker wires), you can choose to have
the 12-volt DC offset feature turn the ampli๏ฌer on when you
turn on the vehicle power, or the audio-sensing feature turn on
the ampli๏ฌer when it detects audio signal. In either case, you
will not have to connect the remote turn-on wire and can tape
or cap it off to prevent the introduction of noise.
โ€ข Connect the remote-out wire to external devices Remote-Out:
that require 12V turn-on after the JBL DSP Ampli๏ฌer. This
connection will allow turn-on of 12V devices after the ampli๏ฌer
wakes from turn-on by 12V remote-in, DC offset or audio
signal sensing input.
Power/Protect indicators
The power light will illuminate in green when the ampli๏ฌer is getting
power and playing. The light will illuminate in red if the amp enters
protect mode in the event of conditions such as over/under voltage,
short circuit, ampli๏ฌer output circuit failure, or excessive heat.
REMOTE
INPUT
LEVEL
LO HI HI2 REM D C AUDI O
TURN-ON
MODE
PC
SPEAKER OUT PUT CHANNELS POWER
REM O UT GN D
GND
GND
12V
12V
12V
REM I N
PRT
PWR
AUDIO
INPUT 8+1+ 2+ 3+ 4 + 5+ 6 + 7+
8-1- 2- 3-
4 - 5 -
6 - 7-
Chassis ground (-)
Remote turn-on
(blue) to stereo
REM out
Battery
Fuse holder, 40A fuse
18" (46cm)
PRODUCT DESCRIPTION
The JBL DSP Ampli๏ฌer is an audio processor for ๏ฌne-tuning of
aftermarket audio systems. It is a self-contained audio system
with 6-channel audio inputs, 8-channel powered audio outputs,
an easy-to-use tuning interface a novice can understand, and
detailed tuning capabilities to satisfy even experienced installers.
With a USB connection to access the tuning interface using a
Windows PC, you can control fully variable crossovers, selectable
0-to-48 dB slopes, time delay, 31-band parametric or graphic EQ
adjustment, assignable input-to-output mixer with input channel
summing, channel gain, master volume control, clipping indicator
to ensure the audio output is not distorted, and ability to save up
to 10 presets.
WHAT'S IN THE BOX
1X
4X
4X 4X 1X
6X
1X
1X
1X
4X
1X
1X
2X 1X
INSTALLATION AND WIRING
IMPORTANT: Disconnect the vehicleโ€™s negative (โ€“) battery
terminal before beginning the installation.
โ€ข Wear protective eyewear when using tools.
โ€ข Choose a safe mounting location. Check clearances on both
sides of the location. Be sure that screws will not puncture
brake or fuel lines or wiring harnesses, and that wire routing will
not interfere with vehicle operation. Use caution when drilling
or cutting.
โ€ข When making electrical connections, make sure they are
secure and properly insulated.
โ€ข Do not mount the ampli๏ฌer with the heat sink facing downward,
as this interferes with cooling.
โ€ข Using the ampli๏ฌer as a template, mark the locations of the
holes on the mounting surface.
โ€ข Drill pilot holes in the mounting surface.
โ€ข Attach the ampli๏ฌer to the mounting surface with the included
sheet metal screws and washers.


Product specificaties

Merk: JBL
Categorie: Receiver
Model: DSP4086

Heb je hulp nodig?

Als je hulp nodig hebt met JBL DSP4086 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver JBL

Handleiding Receiver

Nieuwste handleidingen voor Receiver