Jamo 8A2 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Jamo 8A2 (9 pagina's) in de categorie Luidsprekersysteem. Deze handleiding was nuttig voor 68 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/9
1
Indoor/Outdoor
1A2, 3A2, 3S, 3T, 8A2
2
Congratulations on your purchase of
Jamo Indoor/Outdoor speakers.
Package content.
Speaker (2) Port plug “i” (4) Allen wrench (1)
Assembled bracket (2) Thumb screw “j” (4) Manual (1)
Screw plug “g” (8) Covers “k” (4)
Bracket.
The brackets comes pre-assembled. If disassembling the bracket for paint-
ing, re-assemble it as follow: Place the curved bracket (a) between the wall
bracket (b) and wall bracket cover (c) as shown in fig. 1. Insert two 1” allen
bolts (d) through wall bracket into wall bracket cover and tighten with the
supplied allen wrench. Insert two ½” allen bolts (e) into each side of wall
bracket and tighten towards curved bracket.
Mounting of bracket.
The bracket can be mounted for horizontal or vertical placement of the
speaker. Mount the bracket with four screws (not included) appropriate for
the surface the bracket is mounted to (wood, brick, concrete or other). Take
into account the weight of the speaker (specications on back). A hole (f) in
the middle of the bracket allows for running the speaker wire through the
bracket if so desired. Cover the screws with four screw plugs (g) fig. 2.
Mounting of port plugs.
If the front of the speaker is exposed to rain directly entering the bass reex
ports (under the grill), the ports should be closed to avoid lling the
speaker with water. High moisture is not a problem. Remove the grill (h)
from the speaker and insert two port plugs (i) into the bass ports. Re-install
the grill. The speaker will reproduce less bass with the ports closed.
Fig. 1
b
c
d
e
a
d
e
f
Congratulations on your purchase of
Jamo Indoor/Outdoor speakers
Package content
Speaker (2) Port plug “i” (4) Allen wrench (1)
Assembled bracket (2) Thumb screw “j” (4) Manual (1)
Screw plug “g” (8) Covers “k” (4)
Bracket
The brackets comes pre-assembled. If disassembling the bracket for paint-ing, re-assemble it
as follow: Place the curved bracket (a) between the wall bracket (b) and wall bracket cover
(c) as shown in g. 1. Insert two 1” allen bolts (d) through wall bracket into wall bracket cover
and tighten with the supplied allen wrench. Insert two ½” allen bolts (e) into each side of wall
bracket and tighten towards curved bracket.
Mounting of bracket
The bracket can be mounted for horizontal or vertical placement of the speaker. Mount the
bracket with four screws (not included) appropriate for the surface the bracket is mounted to
(wood, brick, concrete or other). Take into account the weight of the speaker (specications on
back). A hole (f ) in the middle of the bracket allows for running the speaker wire through the
bracket if so desired. Cover the screws with four screw plugs (g) g. 2.
Mounting of port plugs
If the front of the speaker is exposed to rain directly entering the bass reex ports (under the
grill), the ports should be closed to avoid lling the speaker with water. High moisture is not a
problem. Remove the grill (h) from the speaker and insert two port plugs (i) into the bass ports.
Re-install the grill. The speaker will reproduce less bass with the ports closed.
Fig. 1
3
k
k
j
j
h
i
i
g
g
l
Connecting speaker wires
Loosen speaker terminals by turning counter clockwise. Strip ½”/12 mm in-sulation o each
wire. Twist strands on each wire to form “solid” wire.
Insert one wire into each terminal and tighten terminal by turning clockwise. Make sure posi-
tive (+) is to red terminal and negative (-) to black terminal for correct phasing.
Adjustment of I/O 3T
This model is for 70V or 100V line installation. This is mainly used in com-mercial installations
with many speakers and requires an amplier with matching transformer outputs. A switch
located next to the terminals al-lows for adjustments of the level of the speaker in 10W, 5W,
2.5W and 1.25W settings. Adjust the switch to the desired level on each speaker.
Mounting of speaker
Place the speaker inside the curved bracket as shown in g. 2 and insert thumb screws (j)
through each end of the curved bracket into the speaker.
Adjust the speaker to the desired angle and tighten the thumb screws.
In-stall the covers (k) over the thumb screws. The curved bracket can be
ad-justed in the wall bracket by loosening the two ½” allen bolts (e) and
re-tighten them after adjustment.
Fig. 2
Painting
The speaker and bracket can be painted. Spray painting is recommended. Paint all parts before
assembling. Remove the grill from the speaker before painting and cover the front bae (l) of
the speaker. Apply many thin coats instead of a few thick coats to avoid the paint running or
clogging the grill holes. Re-install grill after painting.
Product specificaties
| Merk: | Jamo |
| Categorie: | Luidsprekersysteem |
| Model: | 8A2 |
Heb je hulp nodig?
Als je hulp nodig hebt met Jamo 8A2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Luidsprekersysteem Jamo
1 Juli 2023
1 Juli 2023
1 Juli 2023
1 Juli 2023
1 Juli 2023
1 Juli 2023
1 Juli 2023
1 Juli 2023
1 Juli 2023
Handleiding Luidsprekersysteem
- Luidsprekersysteem Sony
- Luidsprekersysteem Samsung
- Luidsprekersysteem Panasonic
- Luidsprekersysteem AEG
- Luidsprekersysteem Grundig
- Luidsprekersysteem JBL
- Luidsprekersysteem Onkyo
- Luidsprekersysteem Pioneer
- Luidsprekersysteem Toshiba
- Luidsprekersysteem Yamaha
- Luidsprekersysteem American Audio
- Luidsprekersysteem Auna
- Luidsprekersysteem BW
- Luidsprekersysteem Harman Kardon
- Luidsprekersysteem Humax
- Luidsprekersysteem Ion
- Luidsprekersysteem Paradigm
- Luidsprekersysteem Sonos
- Luidsprekersysteem Tevion
Nieuwste handleidingen voor Luidsprekersysteem
14 Augustus 2023
14 Augustus 2023
9 Februari 2023
2 Maart 2023
2 Maart 2023
2 Maart 2023
31 Januari 2023
9 Februari 2023
2 Maart 2023
9 Februari 2023