Intex 28685E Handleiding

Intex Niet gecategoriseerd 28685E

Lees hieronder de 📖 handleiding in het Nederlandse voor Intex 28685E (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 217 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/5

269

(269PO) SOLAR HEATER MAT ENGLISH 4.875” X 7.25” 08/19/2016

SAVE THESE INSTRUCTIONS

Page 1 269-*PO-R0-1708

READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT

INTEX® OWNER'S MANUAL

SOLAR HEATER MAT

REF. NO. DESCRIPTION

QTY.

SPARE PART NO.

Solar heater mat 1 11956

Bypass valve 1 11954

Elbow joint 2 11953

Hose seal 5 10134

Hose clamp 5 11489

Hose 1 11955

Adaptor A (For 1-1/4” hose only) 1 10849

Adaptor B (For 1-1/2” hose only) 1 10722

5*7

1 2

NOTE: Drawings for illustration purpose only. May not reﬂect actual product. Not to scale.

• To reduce the risk of injury, do not permit children to use this product. Always supervise

children and those with disabilities.

• Assembly and disassembly by adults only. This product is not a toy.

• Never allow anyone to step, stand, sit or jump on this product.

• Turn the pump oﬀ before installing, servicing, cleaning or adjusting this product.

• Do not block the outlet of this product while the pump is running.

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR

DEATH.

WARNING

269

(269PO) SOLAR HEATER MAT ENGLISH 4.875” X 7.25” 08/19/2016

General

• This product is for use with storable pools only. Do not use with permanently-installed

pools.

• Solar heater mat size (ﬂat, before ﬁll): 47” X 47” (1.2 m X 1.2 m). Surface area: 11 ft

2 (1m2).

• Suitable for above ground pools up to 8,000 gal (30,280 L).

• Compatible with ﬁlter pump up to 1/3HP or pump ﬂow rate less than 2,000 gal/hr

(7,570 L/hr).

• Increases the pool water temperature by approximately 5-9

oF (3-5o C) depending on

weather and ambient conditions.

Setup instructions

These instructions assume that the pool and ﬁltration system are already assembled, and

there is a pool water return (pool water inlet) hose attached.

1. Unroll and place the solar mat on the selected area where it will receive the maximum sun

exposure. See Fig 1.

2. Position the solar mat between the pool water return hose and the ﬁlter pump outlet, after

the water is ﬁltered.

3. Place the bypass valve over the 2 openings on the solar mat. Ensure the sign “A” marked

on the elbow joint (3) matches the sign “A” on the solar mat opening. Secure the bypass

valve (2) assembly to the solar mat with hose clamps

(5). Ensure all the elbow joints and

hose clamps are securely tightened. See Fig 2.

4. Attach one end of the short hose

(6) to the remaining opening on the bypass valve

(2) and

secure the hose with a hose clamp (5). See Fig 3.

5. Before disconnecting any hoses, turn oﬀ the ﬁltration system and close or cover all pool

inlet and outlets to prevent water from ﬂowing out.

SAVE THESE INSTRUCTIONS

Page 2

47”(1.2 m)

Site Preparation and Requirement

• Select an area that receives maximum direct sunlight for better performance. Face the

solar heater mat in the direction of the sun’s natural path.

• The selected area shall be free of sharp objects, stones and debris that can puncture the

product, and away from traﬃc. Keep all pets away from this product.

• Clear all grass and other vegetation from the selected area as grass and vegetation under

the product will die and may cause odor and slime to develop. Certain types of grass such

as St. Augustine and Bermuda, may grow through the product. Grass growing through the

product it is not a manufacture defect.

• Extend the life of the product, place a tarp or mat on the ground beneath the solar heater

mat.

• Do not place the product on the roof or any structure, or above the water level of the pool.

269

(269PO) SOLAR HEATER MAT ENGLISH 4.875” X 7.25” 08/19/2016

Connection to 1-1/4”(32 mm) hose with clamp

1. Disconnect the pool water return hose from the pump outlet.

2. Connect the other end of the short hose

(6) to the pump outlet. Secure the hose with hose

clamps (5). See Fig 4.

3. Connect the other end of the pool water return hose to the solar heater mat outlet. Secure

the hose with hose clamp

(5) . See Fig 5. Make sure all the hose clamps are securely

tightened.

Connection to 1-1/2”(38 mm) hose with adaptor

1. Disconnect the pool water return hose from the pump outlet.

2. Connect the adaptor A

(7) to the pump outlet and attach the other end of the short hose

(6)

to the adaptor A. Secure the hose with hose clamp

(5). See Fig 6.

3. Attach the adaptor B

(8) to the solar heater mat outlet; then connect the other end of the

pool water return hose to the adaptor B

(8). Ensure the hose clamp (5) and hose nuts are

securely tightened. See Fig 7.

SAVE THESE INSTRUCTIONS

Page 3

Product specificaties

Merk:	Intex
Categorie:	Niet gecategoriseerd
Model:	28685E
Kleur van het product:	Zwart
Breedte:	1219 mm
Diepte:	1219 mm
Gewicht verpakking:	2744 g
Breedte verpakking:	222 mm
Diepte verpakking:	317 mm
Hoogte verpakking:	171 mm
Vorm:	Vierkant
Materiaal:	PVC
Type product:	Zonnescherm