InSinkErator Lia Handleiding

InSinkErator Kraan Lia

Lees hieronder de 📖 handleiding in het Nederlandse voor InSinkErator Lia (8 pagina's) in de categorie Kraan. Deze handleiding was nuttig voor 5 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
F-4N1U-3
F-4N1J-3
F-4N1L-3
The Emerson logo is a trademark and a service mark of Emerson Electric Co.
InSinkErator may make improvements and/or changes in the specifications at any time, in its sole discretion,
without notice or obligation, and further reserves the right to change or discontinue models.
©2020 InSinkErator, InSinkErator a business unit of Emerson Electric Co. All Rights Reserved.
45585-ISE REV A
Installation, Care & Use
ALL-IN-ONE TAP
Multitap -
4N1 Touch
Parex Industries Ltd.
5 Tolich Place, Henderson
Auckland, New Zealand 0610
Sales/Service Tel: 0800 200 510
Email: info.parex@ .co.nzwhirlpool
www.insinkerator.co.nz
InSinkErator
471 Mountain Highway
Bayswater Vic 3153, Australia
Sales/Service Tel: 1300 136 205
Email: sales@insinkerator.com.au
www.insinkerator.com.au
InSinkErator
Emerson Electric Co.
1250 International Drive
Mount Pleasant, WI. 53177
USA
Sales/Service Tel: 800-558-5700
www.insinkerator.com
HOT! This system can dispense near boiling water. Care and
supervision should be taken to avoid scalding.
CAUTION
!
Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
Notice is used to address practices not related to
personal injury.
NOTICE
!
!
WARNING: To reduce the risk associated with choking: Do
not allow children under 3 years of age to have access to
small parts during the installation of this product.
WARNING: Electric Shock Hazard. To reduce the risk
of electric shock, do not immerse or expose the product,
flexible cord or plug to rain, moisture or any liquid or when
standing in or on damp or wet surfaces. If any electrical
product falls into water, UNPLUG it immediately. DO NOT
REACH INTO THE WATER. Important: Prior to reconnecting
to the power supply, the product should be inspected by a
qualified technician.
• Use the water heater only for its intended use as described in
its manual.
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use
of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children without
supervision.
• Do not operate this product if it has been or appears to be
damaged in any manner or after the product malfunctions, or
is dropped. Return the complete product immediately to your
retail dealer for inspection, and if necessary, adjustment or
repair.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
Save these Instructions.
IMPORTANT SAFETY INFORMATION
!
!
WARNING: Personal Injury/Property Damage. To reduce
the risk associated with hazardous voltage due to an
installer drilling through existing electric wiring in the area
of installation: Do not install near electric wiring or water
pipes which may be in path of a drilling tool when selecting
the position to mount the system bracket.
WARNING: Electric Shock Hazard Using an ungrounded
(no earth ground) or improperly connected appliance can
result in serious injury or death from electrical shock.
Important: Always arrange the power cord so that it cannot come in
contact with hot surfaces.
• Do not disconnect the product from the power supply by pulling on
the cord.
• The use of accessory attachments other than those recommended
by the manufacturer may cause safety hazards.
!*
!
!
!
!
!
CAUTION: Personal Injury/Property Damage. This tank is
a non-pressurised tank. DO NOT modify this system. DO NOT
close vent tube or connect other types of taps or valves to
the tank. Use only the InSinkErator tap supplied. Use only
parts provided. Contact an authorised InSinkErator Service
agent for repairs or replacement components.
CAUTION: Personal Injury. If hot water discharges from the
tap while not in use , lower the water temperature of the hot
water tank. If the discharge should then continue, turnoff
and unplug the tank.
NOTICE: Property Damage. To reduce the risk associated
with property damage due to water leakage or flooding, and
to ensure optimal performance:
WARNING: To reduce the risk associated with the
ingestion of contaminants: Do not use with water that is
microbiologically unsafe or of unknown quality without
adequate disinfection before or after the system.
WARNING: Fire Hazard. To minimise possibility of fire, DO
NOT store flammable items such as rags, paper or aerosol
cans near the tank. DO NOT store or use petrol or other
flammable vapours and liquids in the vicinity of this or any
other appliance.
WARNING: Leak Hazard. Regularly inspect tap and
plumbing fittings for leaks, which can cause property
damage and could result in personal injury.
• Read and follow all instructions before installation and
use of this system.
• Installation and use MUST comply with all state and local
plumbing codes.
This appliance must be earthed (grounded). This steaming
hot water tank is equipped with a cord that has a grounding
conductor and earth ground pin. The plug must be connected
to an appropriate outlet that is properly installed and earthed
(grounded) in accordance with all local codes and ordinances.
Do not modify the plug provided with the appliance – if it will
not fit the outlet, have a proper outlet installed by a qualified
electrician. Check with a qualified electrician or tradesman if
you are in doubt as to whether the steaming hot water tank is
properly earthed (grounded).
A steaming hot water tank, like any water heater, has a limited
life and will eventually fail. To avoid possible property damage
and personal injury, this steaming hot water tank should be
regularly examined for leakage and/or corrosion and replaced
when necessary. A drain pan, plumbed to an appropriate
drain or outfitted with a leak detector, should be used in those
applications where any leakage could cause property damage.
IMPORTANT SAFETY INFORMATION
2 3
• Drill, Dedicated control valve, Phillips screwdriver, Pencil,
Tape measure, Level, Tube Cutter
WHAT YOU NEED TO GET STARTED
Equipment Required:
• Anchors for plasterboard, Basin wrench,
Teflon tape, Hole Saw, Hole Punch
Equipment You May Need:
SYSTEM REQUIREMENTS (HOT WATER TANK, FILTRATION SYSTEM AND TAP):
ADDITIONAL CONSIDERATION WHEN UTILISING FILTRATION SYSTEM:
• Make sure that all electrical, plumbing and connections conform to local codes.
• A standard, earthed (grounded) electrical outlet, with continuous supplied power, is required under the sink for the tank.
• This outlet must be fused and should not be controlled by the same wall switch that operates the disposer, unless you have a
SinkTop Switch™ from InSinkErator
®. Fuse/circuit breaker required is 10 amp for 230 or 220-240 volt and 15 amp for 120 volt.
• In Australia and New Zealand, all plumbing and electrical work must be completed by a qualified tradesperson. The installation
must conform to AS/NZS3500.4 and AS/NZS3000.
• Do not install the filter on hot water supply lines. The maximum operating water temperature of this system is 38°C (100°F).
Attach the filter to the cold water supply only.
• The hot water supply should not exceed 65ºC (149ºF)
• It is recommended that a dedicated control valve be installed on the cold water line supplying water to the filter system.
• To prevent damage or unit not operating properly, the water pressure must be between 210 kPa –860 kPa (2.1 bar - 8.6 bar; 30
psi - 125 psi). Ambient (room) temperature between 4°C (40°F) and 43°C (110°F).
• Do not install if water pressure exceeds 860 kPa (125 psi). If your water pressure exceeds 550 kPa (80 psi), you must install
a pressure limiting valve. In Australia and New Zealand, a Watermark certified AS/NZS2845.1 350 kPa (50 psi) set pressure
limiting valve and dual check valve must be used.
• The use of a water filter should NOT result in the water pressure dropping below 210 kPa (30 psi).
• Do not install where water hammer conditions occur. If water hammer conditions exist you must install a water hammer
arrester.
• The flexible vent and outlet tubes must be correctly connected to the tap supplied by the manufacturer. They must not be
obstructed or connected to a normal type tap or any other type.
• Protect from freezing, shut off water supply, remove filter cartridge, drain hot water tank and tubing when temperatures are
expected to drop below 4°C (40°F).
• Do not use a torch or other high temperature sources near system, cartridges, plastic fittings or plastic plumbing.
• Do not install near water pipes which will be in path of a drilling tool when selecting the position to mount components.
• Mount system in such a position as to prevent it from being struck by other items used in the area of installation.
• Ensure that the location and fasteners will support the weight of the system when installed and full of water.
• When mounting components, screws provided are for use in wood studs or cabinets only. Use wall anchors (not supplied) for
installation into plasterboard.
• Ensure all tubing and fittings are secure and free of leaks.
• Do not install using rigid piping. System intended for use with plastic water lines (such as PEX tubing, PE tubing, PP tubing).
• Do not install this system if any of the quick connect collets are missing from the filter head or Quick Connectors. Contact an
authorized InSinkErator Service agent if collets are missing from any fittings.
• Important: Do not allow the unit to continuously boil.
• Regularly inspect the system. If there are signs of water leakage, turn off the water supply and contact an authorised
InSinkErator Service agent.
• A drain pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in those applications where any
leakage could cause property damage.
• If you suspect elevated levels of chlorine in your water, or your water has a rusty appearance before the installation of this unit,
use of our water filtration system is recommended.
• This product contains stainless steel. The manufacturer cannot guarantee against rusty water because of the number of factors
that are involved beyond the manufacturer’s control. However, the sudden appearance of rusty water discharged from the hot
water tap may indicate the need for service or replacement of this product.
• Moving parts inside the tank causing a rattling noise is normal.
• For questions or concerns, please contact an authorised InSinkErator Service agent (see back page for contact information).
• The disposable filter cartridge MUST be replaced every 6 months, at the rated capacity or sooner if a noticeable reduction in
flow rate occurs.
• Failure to replace the disposable filter cartridge at recommended intervals may lead to reduced filter performance and cracks in
the filter housing, causing water leakage or flooding.
• Protect from freezing, remove filter cartridge when temperatures are expected to drop below 4°C (40°F).
• Do not install systems in areas where ambient temperatures may go above 43°C (110°F).
• Do not install in direct sunlight or outdoors.
!
• Please refer to the Installation, Care & Use manual packaged with your hot water tank and filtration system for additional
Important Safety Information and installation instructions.
For your satisfaction and safety, read all instructions, cautions and warnings before installing or using this tap.
• This particular unit is not for commercial/industrial use.
WHAT YOU SHOULD KNOW BEFORE YOU BEGIN
Tap Components
13
14
11
12
15
16
20
18
19
17
22
21
4
6
5
2
3
8
9
10
7
1
BA
OUT
IN
23 24
25
26
28
27
+
29
1. Tap
2. Main Tap Cold/Hot Water Inlet Tubes
3. Short Copper Tube - Not Labeled
4. Wire From Tap to Solenoid Valve
5. Wire From Tap to Battery
6. Clear Vent Tube
7. Copper Tubes Labeled A and B
8. White Aspirator Tube
9. Tank Outlet Tube with Check Valve
10. Plastic Tube, 1.2 M (47") Long
11. Small Rubber O-Ring
12. Plastic Brace
13. Large Rubber O-Ring
14. Metal Ring
15. Mounting Ring
16. Mounting Screws (3)
17. Mounting Screws for Solenoid Valve Assembly (4)
18. Union Quick Connect
19. “T” Fitting - Quick Connect
20. Solenoid Valve Assembly
21. 9-Volt Alkaline Battery
22. Battery Case and Wire Connection
23. Hot Water Tank
24. Filter Head and Cartridge
25. Y - Quick Connector and Plug
26. Mounting Screws For Tank and Filter (4)
27. Connector 12.7 mm to 9.5 mm (1/2" to 3/8")
28. Pressure Limiter & Back Flow Preventor
29. Filter Tubes (2)
PARTS
Hot Water Tank and Filtration Components
4 5
IMPORTANT INSTALLATION INFORMATION
Notice Property Damage: Before installing this system be aware of the following requirements to avoid water leakage which could
cause property damage. After completing installation check the system to ensure these requirements are complied with.
Braided Tubes:
Quick Connections:
Plastic Tubing:
Maintain a minimum
tube bend of = 2.4” (60mm)
Ensure that the tubes are straight
near the quick connections. Avoid
side loading the quick connection.
Ensure that the tube is pushed all
the way into the quick connection.
Ensure tube is not kinked
or damaged.
Keep the tube straight near its
connection for 3/4” (19 mm)
Do not stretch the tubing to
make the connection
Regularly inspect all quick connections for leaks.
Turn off the water supply immediately if a leak
is detected or the connector appears damaged.
Replace the quick connector before turning the
water back on.
If cleaning any of the connection or tubing, use
only water.
1/4” OD Tubing: Minimum is 1” (25.4 mm)
3/8 OD Tubing: Minimum is 1.25” (31.8 mm)
Ensure the plastic tube with the
quick connection that is attached
to the hot water tank is straight for
1” (25.4 mm) above the connection.
ø min.
ø min.
X

Product specificaties

Merk: InSinkErator
Categorie: Kraan
Model: Lia

Heb je hulp nodig?

Als je hulp nodig hebt met InSinkErator Lia stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Kraan InSinkErator

InSinkErator

InSinkErator Juno Handleiding

3 Maart 2025
InSinkErator

InSinkErator Lia Handleiding

3 Maart 2025

Handleiding Kraan

Nieuwste handleidingen voor Kraan

Billi

Billi B-5000 Sparkling Handleiding

3 Maart 2025
Gessi

Gessi 20573 Handleiding

25 Februari 2025
IKEA

IKEA LUNDSKÄR 405.328.03 Handleiding

13 Februari 2025
IKEA

IKEA LUNDSKÄR 205.326.15 Handleiding

15 Januari 2025
Pfister

Pfister Kelen LG42-MF1K Handleiding

18 December 2024
Moen

Moen M-PRESS 8886 Handleiding

18 December 2024
Moen

Moen M-PRESS 8889 Handleiding

18 December 2024
Moen

Moen M-PRESS 8884 Handleiding

18 December 2024
Moen

Moen M-BITION 8917 Handleiding

18 December 2024
Moen

Moen M-BITION 8922 Handleiding

18 December 2024