Infinity Marine 6001A Handleiding

Infinity Receiver Marine 6001A

Lees hieronder de šŸ“– handleiding in het Nederlandse voor Infinity Marine 6001A (25 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/25
Marine 6001A
Marine 10001A Ampliļ¬ers
EN
DE
ES
IT
NL
FR
Ownerā€™s Manual
Mode dā€™emploi
Bedienungsanleitung
Manual de propietario
Manuale d'istruzioni
Gebruikershandleiding
INPUT
LEVEL
GAIN
FREQ
BASS
BOOST
PHASE
TURN-ON
MODE
HI2
HI1
LO
MAX
MIN
320Hz
32Hz
12dB
0dB
0Ā°
180Ā°
DC
REM
6001A
INPUT REMOTE
CONTROL
L
R
SUB
+-+-FUSE
30A 30A +12V REM GND PWR /PROT
MODE
PRIMARY
SECONDARY
PHASE
TURN-ON
MODE
DC
REM
INPUT
LEVEL
BASS
BOOST
FREQ
GAIN
HI2
12dB
0dB
320Hz
MAX
MIN
32Hz
HI1
LO
0Ā°
180Ā°
10001A
INPUT
L
R
PRIMAR Y OUT
SECONDARY IN SUB
+-+-
REMOTE
CONTROL FUS E
35A 35A 3 5A +12V REM GND PWR/ PROT
EN
Marine 6001A
Marine 10001A Ampliļ¬ers
ACCESSING CONNECTORS AND CONTROL
PANEL
1. Slide the panel cover down
2. Remove panel cover
10001A
MOUNTING THE AMP
10001A
Note: It is recommended that you make all wire connections
before permanently mounting the amp.
WHAT'S IN THE BOX
Marine 6001A
Marine 10001A
EN
EN
IMPORTANT: Disconnect the negative (ā€“) battery terminal of
the accessory battery before beginning the installation.
ā€¢ Always wear protective eyewear when using tools.
ā€¢ Choose a safe mounting location. Check clearances on both
sides of a planned mounting surface. Be sure that screws
or wires will not puncture the vessel hull, fuel lines, or wiring
harnesses, and that wire routing will not interfere with the safe
boat operation. Use caution when drilling or cutting in the
mounting area.
ā€¢ Choose a location that provides enough air circulation.
ā€¢ Do not mount the ampliļ¬er with the heat sink facing downward,
as this interferes with cooling.
ā€¢ Mount the ampliļ¬er so that it will not be damaged by the feet of
passengers or shifting cargo.
WIRING FOR POWER AND GROUND
At ampliļ¬er:
+12V REM GND
Fuse holder, fuse
Chassis ground (ā€“)
Remote turn-on to
aftermarket stereo REM out
(used only with low-level signal inputs)
Battery
18 (46cm)ā€
At ground location:
Ring Connector
Ground Wire
Star Washer
Factory Bolt
Note: Remove any paint
below ring connector
WIRING FOR INPUT SIGNAL
Low-level signals
INPUT
From stereo subwoofer
low-level outputs
DC
REM
TURN-ON
MODE
HI2
HI1
LO
INPUT
LEVEL
Note: when using low-level signals and remote turn-on lead, set the
" " " switch to " " and the "
switch to " ".
High-level signals
INPUT
Stereo front or rear
speaker wires
DC
REM
TURN -ON
MODE
HI2
HI1
LO
INPUT
LEVEL
Loosen
Screws
Insert
Wires
Tignten
Screws
Note: when using high-level signals, set the " "
switch to " " and the " " switch to " ". If no
sound plays, change the " " switch to " ".
CONNECTING TWO MARINE 10001A
AMPLIFIERS FOR EXTRA POWER
To connect two Marine 10001a ampliļ¬ers, use an RCA patch
cable to connect the ā€œ ā€ of the primary ampliļ¬er to PRIMARY OUT
the ā€œ ā€ of the secondary ampliļ¬er. Set the Primary/SECONDARY IN
Secondary switch to ā€œ ā€ on the primary ampliļ¬er, and to PRIMARY
ā€œ ā€ on the secondary ampliļ¬er.SECONDARY
PRIMARY OUT
SECONDARY IN
PRIMARY OUT
SECONDARY IN
PRIMARY
SECONDARY
MODE
AMP 1:
AMP 2:
PRIMARY
SECONDARY
MODE


Product specificaties

Merk: Infinity
Categorie: Receiver
Model: Marine 6001A

Heb je hulp nodig?

Als je hulp nodig hebt met Infinity Marine 6001A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Infinity

Handleiding Receiver

Nieuwste handleidingen voor Receiver