Infinity Kappa One Handleiding

Infinity Receiver Kappa One

Lees hieronder de 📖 handleiding in het Nederlandse voor Infinity Kappa One (4 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

K A P P A

KAPPA

® ONE



A B C D



4x 1x

¡





   

 

Installation Warnings and Tips

•Disconnect the negative (–) lead from your vehicle’s battery.

•Attheinstallationsites,locateandmakeanoteofallfuel

lines, hydraulic brake lines, vacuum lines and electrical

wiring. Use extreme caution when cutting or drilling in and

around these areas.

•Chooseasafemountinglocationawayfrommoisture.

•Makesurethereissufcientaircirculationatthemount-

ing location for the ampliﬁer to cool itself.

•Mounttheamplier,usingthesuppliedhardware.

Speciﬁcations

•500WRMSx1channel@4ohms

–1% THD + N*

•800WRMSx1channel@2ohms

–1% THD + N*

•Total peak power: 1600W

•Frequency response: 20Hz – 320Hz 3dB)(–

•Maximuminputsignal:6V*

•Maximumsensitivity:200mV*

•THD + N: 0.05%

•Signal-to-noise ratio: 85dBA (reference to 1 watt)*

•Signal-to-noise ratio: 109dBA (reference to rated power)

* CEA-2006A-compliant

0 Speaker Output Connectors

 •Connectthespeakerstotheseterminals,observing

proper polarity. Gold screws indicate +, and silver

screws indicate – .

 •Minimumspeakerimpedanceis2ohms.

1 Fuses

 •Replaceonlywiththesametypeandrating.

2 Power Input Connectors

 •+12V:Connecttothepositiveterminalofthevehicle’s

battery. Install an appropriate fuse holder and fuse

(120Aminimum)within18”(457mm)ofthebattery.

Makesurethewireisnotdamagedorpinchedduring

installation. Install protective grommets when routing

wires through the ﬁrewall or other sheet metal.

 •GND:Connecttothevehicle’schassis.Refertothe

illustration below.

 •REM:Connecttothe“RemoteOut”leadfromthe

source unit or to a source of switched +12V(ACC).

4 AWG Adapter

•Forpowerwirelongerthan4’(1.2m),4AWGwireis

recommended. Use the adapter to make the connection

according to the illustration below.

3 DBO: Variable Subsonic High-Pass

Filter With Variable Boost (Q)

 •Forwoofersintuned(vented)enclosures,setthe

frequency control to a value 10Hz below the enclo-

sure’s resonance (tuned) frequency.

 •Forwoofersinsealedboxes,setthecontroltoany

value you prefer between 30Hz and 50Hz.

 •SettheBoostcontrolaccordingtoyourpreference,

being careful not to apply enough boost to damage

your woofer(s).

ADBOBoostcontrolprovidesupto12dBofboost,

slightly above the high-pass ﬁlter’s frequency.

See above for appropriate settings.

BDBOHigh-PassFilterFrequencycontrol,variable

between 10Hz and 80Hz. See above for appropri-

ate settings.

4 Crossover-Frequency Control

 •12dB/octavecrossover,variablefrom32Hzto320Hz.

See  for the adjustment procedure.

 Input Level Control

 •Usedtomatchtheinputleveloftheamplierto

the output level of the source unit. See A for the

adjustment procedure.

 Input Connectors

 •Connecttofrontoutputsfromthesourceunitor

signal processor.

 Aux Output Connectors

 •Nonlteredpass-throughoutput.Connecttothe

input of an additional subwoofer ampliﬁer.

 Protect LED

 •Illuminatedunderanyofthefollowingfault

conditions: battery over/under voltage; short

circuit in speaker wires; ampliﬁer is too hot;

ampliﬁer’s output circuit has failed (DC voltage

present in the ampliﬁer’s output).

 Power On LEDs

 •Illuminatedwhentheamplierison.

A Setting Input Level

ATurnInputLevelcontrolcounterclockwiseto6V.

With a dynamic music track playing, turn the head B

unit’svolumecontroltothe3/4position.

Turn Input Level control clockwise until the bass C

output is proportionate to the output of the high-

frequency speakers, according to your preference.

Input level is now adjusted correctly.D

 Setting the Crossover

Crossover setting for subwoofers.A

Acceptable frequency ranges indicated in gray.Note:

Factory Bolt Ring Connector

Ground Wire

Note: Remove any paint

below ring connector.

Star Washer

This product is designed for mobile applications and is not intended

for connection to the mains.

A valid serial number is required for warranty coverage.

Features, speciﬁcations and appearance are subject to change

without notice.

ENGLISH

Product specificaties

Merk:	Infinity
Categorie:	Receiver
Model:	Kappa One
Kleur van het product:	Zwart, zilver
Breedte:	179 mm
Diepte:	44 mm
Hoogte:	329 mm
Connectiviteitstechnologie:	Bedraad
Audio-ingang (L, R):	2
Audio-uitgangskanalen:	1.0 kanalen
Frequentiebereik:	20 - 320 Hz
Signaal/ruis-verhouding:	112 dB
Totale harmonische vervorming (THD):	- procent
Piekvermogen per kanaal:	1600 W
Versterker klasse:	D
RMS vermogen uitvoer per kanaal (4 Ohm):	500 W
RMS vermogen uitvoer per kanaal (2 Ohm):	800 W