Infiniton TEC-80 Handleiding

Infiniton Ketel & boiler TEC-80

Lees hieronder de 📖 handleiding in het Nederlandse voor Infiniton TEC-80 (57 pagina's) in de categorie Ketel & boiler. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/57

The diagram above is just for reference. Please take the

appearance of the actual product as the standard.

Instruction Manual

For Model: TEC-50

TEC-80

TEC-100

The installation and maintenance has to be carried out by qualified professionals or authorized

technicians.

The manufacturer shall not be held responsible for any damage or malfunction caused by

wrong installation or failing to comply with following instructions included in this pamphlet.

TABLE OF CONTENTS

TITLE PAGE

1.Cautions ...........................................................................................................................(2)

2.Product introduction .........................................................................................................(3)

3.Unit installation .................................................................................................................(5)

4.Methods of using ..............................................................................................................(7)

5.Maintenance.....................................................................................................................(7)

6.Troubleshooting................................................................................................................(8)

7.Produce information with EU regulation ...........................................................................(9)

●

General Remark

The water heater is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instructions concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the heater.

The wall in which the electrical water heater is installed must be able to bear the load more than

two times of the heater filled fully with water without distortion and cracks. Otherwise, other

strengthening measures must be adopted.

The supply socket must be earthed reliably. The installation height of the supply socket must not

be lower than 1.8m. The rated current of the socket must not be lower than 16A. The socket and

plug must be kept dry to prevent electrical leakage. If the flexible power supply cord is damaged, the

special supply cord provided by the manufacturer must be selected, and replaced by the professional

maintenance personnel.

The maximum inlet water pressure is 0.5MPa; the minimum inlet water pressure is 0.1MPa, if this

is necessary for the correct operation of the appliance.

When using the heater for the first time (or the first use after maintenance), the heater can not be

switched on until it has been filled fully with water. When filling the water, at least one of the outlet

valves at the outlet of the heater must be opened to exhaust the air. This valve can be closed after

the heater has been filled fully with water.

The pressure relief valve attached with the heater must be installed at the cold water inlet of this

heater, and make sure it is not exposed in the foggy. The water may be outflowed from pressure

relief valve, so the outflow pipe must open wide in the air. In order to drain away the water inside

the inner container, it can be drained away from the pressure release valve. Twist the thread screw

of the pressure release valve off, and lift the drain handle upwards(See Fig.1) . The drainage pipe

connected to the pressure release hole must be kept sloping downwards and in a frost-free

environment. The water may drip from the discharge pipe of the pressure-relief device and that this

pipe must be left open to the atmosphere.

During heating, there may be drops of water dripping from the pressure release hole of the

pressure relief valve, this is a normal phenomenon. The pressure release hole shall not be blocked

under no circumstances, otherwise, the heater may get damaged, even resulting in accidents. If

there is a large amount of water leak, please contact customer care center for repair.

The pressure relief valve need to be checked and cleaned regularly, so as to make sure it will not

be blocked.

Since the water temperature inside the heater can reach up to 75 , the hot water must not be ℃

exposed to human bodies when it is initially used. Adjust the water temperature to a suitable

temperature to avoid scalding.

If any parts and components of this electrical water heater are damaged please contact customer

care center for repair.

Before installing this water heater,check and confirm that the earthing on the supply socket is

reliably grounded. Otherwise, the electrical water heater can not be installed and used. Do not use

extension boards. Incorrect installation and use of this electrical water heater may result in serious

injuries and loss of property.

Special Cautions

1. CAUTIONS

Product specificaties

Merk:	Infiniton
Categorie:	Ketel & boiler
Model:	TEC-80
Kleur van het product:	Wit
Ingebouwd display:	Ja
Breedte:	450 mm
Diepte:	450 mm
Hoogte:	796 mm
Geluidsniveau:	15 dB
Energie-efficiëntieklasse:	C
Jaarlijks energieverbruik:	1420 kWu
Soort:	Tank (wateropslag)
Internationale veiligheidscode (IP):	IPX4
LED-indicatoren:	Ja
Aan/uitschakelaar:	Nee
Capaciteit watertank:	80 l
Ondersteuning voor plaatsing:	Verticaal
Instelbare thermostaat:	Ja
Temperatuur (max):	75 °C
Maximaal vermogen:	2000 W
AC-ingangsspanning:	220 - 240 V
Verwamingslocatie:	Binnen
Boiler systeem:	Solo-boilersysteem
Warmwatercapaciteit:	- l/min
Ontstekings type:	Elektronisch