Induction Dynamics S2.LR Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Induction Dynamics S2.LR (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
H
A
N
D
C
R
A
F
T
E
D
I
N
A
M
E
R
I
C
A
H
A
N
D
C
R
A
F
T
E
D
I
N
A
M
E
R
I
C
A
FREESTANDING SPEAKERS
OWNER’S MANUAL
Rev 07.01.2019
urin Exceence™ Manufacturin Exceence™
Man
nce
™ Manufacturin Exceence™
Manufacturin Ex
Exceence
™ Manufacturin Exceence™
Manufact
Manufacturin Exceence
™
Manufacturin Excee
Manufacturin Exceence
™ Manufacturin Exceence™
urin Exceence
™ Manufacturin Exceence™
Man
nce
™ Manufacturin Exceence™
Manufacturin Ex
Exceence
™
Manufacturin Exceence
™
Manufact
FREESTANDING SPEAKERS
Please read the following instructions carefully before installing your Induction Dynamics ÂŽ freestanding speakers. If you have
any questions regarding installation that are not answered in the following directions, please contact your local sound contractor
or the Induction DynamicsÂŽ/MSE AudioÂŽ technical support team. Contact information can be found on the back of the manual.
General Information
Your speakers and amplier come in a high quality nish that is both attractive and durable. To clean, use a soft, damp cloth. If
your drivers become dusty, dust them with a paintbrush or a brush vacuum attachment. Do not use a strong or abrasive cleaner.
The grille is covered in acoustic cloth. To keep your grille clear of debris, we recommend you use a lint roller (like you would use
on clothes).
Do not use bass or loudness contour controls. Induction Dynamics’ subwoofers produce very low frequencies without these
controls. Use of these controls will make the bass sound “boomy”, obscure higher frequencies, and possibly cause damage
due to excessive cone excursion.
Amplifer location: The A2 amplier is best located in an equipment rack or shelving with other audio and video equipment. It is
not recommended for placement behind walls or other limited access locations, where service may be restricted.
Carpet spikes are not required for these speakers. However, they have been provided if you would prefer to use them. Should
you choose to do so, lay the speaker on its back side, then screw the carpet spikes into the threaded holes under the base of
each speaker.
Speaker Wiring: Use approved wire designed for in-wall or exposed use, as appropriate for your installation. For freestanding
speakers, we recommend using high-quality speaker wire that is 12 gauge or lower, with easily visible polarity coding to make
your connections. The following chart identies minimum gauge requirements for various lengths. See your local dealer or
installation contractor for more information.
Length in Feet
Up to 18’
Up to 29’
Up to 51’
AWG Size & Stranding
14 Gauge (19/27)
12 Gauge (65/30)
10 Gauge (105/30)
Wire Length / Minimum Gauge
Requirements
Subwoofer Connection
The jumpers should be removed and the switch set to “Three-way + Subwoofer”. Connect the lower binding posts on the back
of the ID1 or ID1.15 to the A2 subwoofer amplier in series using reverse polarity (red to black and black to red). Below are
diagrams showing alternative methods of connecting the subwoofers, to achieve the in-series, reverse-polarity connections.
Power Connection
Connect the A2 amplier to a 120 volt, single phase, 60 Hz, grounded power supply using the power cord provided. For best
results, use a dedicated power circuit for your amplication equipment.


Product specificaties

Merk: Induction Dynamics
Categorie: Speaker
Model: S2.LR

Heb je hulp nodig?

Als je hulp nodig hebt met Induction Dynamics S2.LR stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker Induction Dynamics

Handleiding Speaker

Nieuwste handleidingen voor Speaker