Indesit IWDE 7125 B (UK) Handleiding

Indesit Was-droog combinaties IWDE 7125 B (UK)

Lees hieronder de 📖 handleiding in het Nederlandse voor Indesit IWDE 7125 B (UK) (16 pagina's) in de categorie Was-droog combinaties. Deze handleiding was nuttig voor 55 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/16
GB
1
! This symbol reminds you to read this booklet.
Contents
Installation, 2-3-4-5
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 6
Cutting off the water or electricity supply
Cleaning the Washer-dryer
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 7
General safety
Disposal
Description of the Washer-dryer, 8-9
Control panel
Display
How to run a wash cycle or a drying cycle, 10
Wash cycles and options, 11
Table of wash cycles
Wash options
Detergents and laundry, 12
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 13-14
Product Guarantee and Repair Information, 15
IWDE 7125
Instructions for use
WASHER-DRYER
English,1
GB
2
GB
Installation
! Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction
manual accompanies the washer-dryer to inform
the new owner as to its operation and features.
! Read these instructions carefully: they contain
vital information on installation, use and safety.
Unpacking and levelling
Unpacking
1. Unpack the washer-dryer.
2. Check whether the washer-dryer has been
damaged during transport. If this is the case, do
not install it and contact your retailer.
3. Remove the pro-4
tective screws and the
rubber bush with the
respective spacer, si-
tuated on the rear of the
appliance (see also the
installation leaflet).
4. Seal the gaps using the plastic plugs provided.
5. Keep all the parts: you will need them again if
the washer-dryer needs to be moved to another
location.
! Packaging materials are not children’s toys.
Levelling
Your machine may make a considerable amount
of noise if the two front feet have not been adju-
sted correctly.
1. Install the washer-dryer on a flat sturdy floor,
without resting it up against walls, furniture ca-
binets or other.
2. If the floor is not per-
fectly level, compensate
for any unevenness by
tightening or loosening
the adjustable front feet
(see figure); the angle
of inclination, measu-
red according to the
worktop, must not ex-
ceed 2°.
Levelling your appliance
correctly will provide it with stability and avoid
any vibrations, noise and shifting during ope-
ration. If it is placed on a fitted or loose carpet,
adjust the feet in such a way as to allow enough
room for ventilation beneath the washer-dryer.
Electric and water connections
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it to
a cold water tap using
a 3/4 gas threaded
connection (see figure).
Before performing the
connection, allow the
water to run freely until
it is perfectly clear.
2. Connect the other
end of the water inlet
hose to the washer-
dryer, screwing it onto
the appliance’s cold
water inlet, situated on
the top right-hand side
on the rear of the ap-
pliance (see figure).
3. Make sure there are no kinks or bends in the
hose.
! The water pressure at the tap must be within
the values indicated in the Technical details
table (on the page 5).
! If the water inlet hose is not long enough,
contact a specialist store or an authorised
serviceman.
! Ensure that the supply taps are allowing wa-
ter through. Old taps may seize in the closed
position and thus prevent water reaching the
machine.
GB
3
Connecting the drain hose
Connect the drain
hose, without bending
it, to a draining duct or
a wall drain situated
between 65 and 100
cm from the floor;
The drain hose may
be connected to an
under-sink trap. Be-
fore connecting the
drain hose from the
machine ensure that
any blanks or remo-
vable ends have been
taken off the spigot.
If it is placed over the
edge of a basin or sink
be sure the free end of
the hose should not
be underwater.
! We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length. Ensure that if the drain
hose is pushed into a standpipe, that the end does
not go down more than 15cms (6 inches). If the hose
is pushed down too far, this may cause the machine
to self -syphon ie. continuously empty as it is filling.
Electric connection
Before plugging the appliance into the mains
socket, make sure that:
• the socket is earthed and in compliance with
the applicable law;
• the socket is able to sustain the appliance’s
maximum power load indicated on the Technical
Data Plate fixed on the machine;
65 - 100 cm
Where it connects to
the waste water pipe
cut end off spigot or
remove the blanking cap
• the supply voltage is included within the values
indicated on the Technical Data Plate fixed on
the machine.
• the socket is compatible with the washer-
dryer’s plug. If this is not the case, replace the
socket or the plug.
Your appliance is now supplied with a 13 amp fu-
sed plug it can be plugged into a 13 amp socket
for immediate use. Before using the appliance
please read the instructions below.
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be
used, and the fuse cover re-fitted. If the fuse
cover is lost, the plug must not be used until a
replacement is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of
the correct colour as indicated by the coloured
marking or the colour that is embossed in words
on the base of the plug. Replacements can be
obtained directly from your nearest Service Depot.
Removing the plug:
If your appliance has a non-rewireable moulded
plug and you should wish to re-route the mains
cable through partitions, units etc., please en-
sure that either:
the plug is replaced by a fused 13 ampere rewi-
reable plug bearing the BSI mark of approval.
or:
the mains cable is wired directly into a 13 amp
cable outlet, controlled by a switch, (in complian-
ce with BS 5733) which is accessible without
moving the appliance.
Disposing of the plug:
Ensure that before disposing of the plug itself,
you make the pins unusable so that it cannot be
accidentally inserted into a socket.
Instructions for connecting cable to an alterna-
tive plug:
Important: the wires in the mains lead are co-
loured in accordance with the following code:
Green & Yellow Earth
Blue Neutral
Brown Live


Product specificaties

Merk: Indesit
Categorie: Was-droog combinaties
Model: IWDE 7125 B (UK)

Heb je hulp nodig?

Als je hulp nodig hebt met Indesit IWDE 7125 B (UK) stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Was-droog combinaties Indesit

Handleiding Was-droog combinaties

Nieuwste handleidingen voor Was-droog combinaties