Indesit IDL 5055 SK.2 Handleiding

Indesit Vaatwassers IDL 5055 SK.2

Lees hieronder de πŸ“– handleiding in het Nederlandse voor Indesit IDL 5055 SK.2 (56 pagina's) in de categorie Vaatwassers. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/56
English,1
Suomi, 45 Dansk, 34
Norsk, 12
NOE N SV
FI
DA
Svenka, 23
DISHWASHER
Contents
Installation, 2-3
Positioning and levelling
Connecting the water and electricity supplies
Technical data
Description of the appliance, 4
Overall view
Control panel
Loading the racks, 5
Lower rack
Cutlery basket
Upper rack
Start-up and use, 6
Starting the dishwasher
Loading the detergent
Washing options*
Wash cycles, 7
Wash cycle table
Rinse aid and refined salt, 8
Loading the rinse aid
Loading the refined salt
Care and maintenance, 9
Shutting off the water and electricity supplies
Cleaning the dishwasher
Preventing unpleasant odours
Cleaning the sprayer arms
Cleaning the filters
Leaving the machine unused for extended periods
Precautions and advice, 10
General safety
Disposal
Saving energy and respecting the environment
Troubleshooting, 11
Instruction booklet
IDL 5055
2
EN
 Keep this instruction manual in a safe place for
future reference. If the appliance is sold, given away
or moved, please ensure the manual is kept with the
machine, so that the new owner may benefit from the
advice contained within it.
 Please read this instruction manual carefully: it
contains important information regarding the safe
installation, use and maintenance of the appliance.
 If the appliance must be moved at any time, keep
it in an upright position; if absolutely necessary, it
may be tilted onto its back.
Positioning and levelling
1. Remove the appliance from all packaging and
check that it has not been damaged during
transportation.
If it has been damaged, contact the retailer and do
not proceed any further with the installation process.
2. Check the dishwasher by placing it so that its
sides or back panel are in contact with the adjacent
cabinets or even with the wall. This appliance can
also be recessed under a single worktop* (
see the
Assembly instruction sheet
).
3. Position the dishwasher on a level and sturdy floor.
If the floor is uneven, the front feet of the appliance
may be adjusted until it reaches a horizontal position
(the angle of inclination must not exceed 2 degrees).
If the appliance is levelled correctly, it will be more
stable and much less likely to move or cause
vibrations and noise while it is operating.
Connecting the water and electricity
supplies
 Connection to the water and electricity supplies
should only be performed by a qualified technician.
 The dishwasher should not stand on top of the
water hoses or the electricity supply cable.
The water inlet (A) and outlet (B) hoses and the
electricity supply cable may be positioned towards
the right or the left in order to achieve the best
possible installation (
see figure
).
Connecting the water inlet hose
β€’ To a suitable cold water connection point: before
attaching the hose, run the water until it is
perfectly clear so that any impurities that may be
present in the water do not clog the appliance;
after performing this operation, screw the inlet
hose tightly onto a tap with a ΒΎ gas threaded
connection.
β€’ To a suitable hot water connection point: your
dishwasher may be provided with hot water from
the mains supply (if you have a central heating
system with radiators) provided that it does not
exceed a temperature of 60Β°C.
Screw the hose to the tap as described for
connection to a cold water supply.
 If the inlet hose is not long enough, contact a
specialist store or an authorised technician (
see
Assistance
).
 The water pressure must be within the values
indicated in the Technical data table (
see below
).
 The hose should not be bent or compressed.
Anti-flooding protection
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the
water supply in the event of anomalies or leaks from
inside the appliance.
- is provided with a
Water Stop
* safety device, in
other words it has a water inlet hose that consists of
a transparent hose on the outside and a red hose on
the inside: both the hoses can withstand extremely
high pressure. If the internal hose breaks, the
external hose becomes a bright red colour and
carries the water instead, thus avoiding any leakage.
 It is very important to check the external hose
regularly: if it is a bright red colour, it must be
replaced by an authorised technician as soon as
possible (
see Assistance
).
* Only available in selected models.
148
12083
121168
100
60
A
B
Installation
3
EN
Connecting the water outlet hose
Connect the outlet hose (without bending it) to a
drain duct with a minimum diameter of 4 cm.
Alternatively, rest it over a sink or tub; the free end
of the hose should not remain immersed in water.
The special plastic
elbow* makes it easier to
find the best layout: fix
the elbow to the wall
securely in order to
prevent the outlet hose
from moving and spilling
the dirty water.
The part of the hose
marked with the letter A
should be between 40 and 100 cm above the ground
(
see figure
).
 We advise against the use of hose extensions.
Electrical connection
Before inserting the plug into the electrical socket,
make sure that:
β€’ the socket is earthed and complies with current
regulations;
β€’ the socket can withstand the maximum load of
the appliance, which is indicated on the data
plate located on the inside of the door (
see
Description of the appliance
);
β€’ the power supply voltage falls within the values
indicated on the data plate on the inside of the
door;
β€’ the socket is compatible with the plug of the
appliance. If this is not the case, ask an
authorised technician to replace the plug (
see
Assistance
); do not use extension cables or
multiple sockets.
 Once the appliance has been installed, the power
supply cable and the electrical socket should be
easily accessible.
 The cable should not be bent or compressed.
 The cable should be checked regularly and
replaced by authorised technicians only (
see
Assistance
).
 The Company shall not be held responsible for any
incidents that occur if these regulations are not
observed.
Advice regarding the first wash cycle
After the appliance has been installed, immediately
before running the first wash cycle, completely fill
the salt dispenser with water and add approximately
2 kg of salt (
see Rinse aid and refined salt
). The
water may overflow: this is normal and is not a
cause for concern. It is also normal that the LOW
SALT* indicator light continues to flash for a few
cycles after the salt has been loaded.
A
* Only available in selected models.
Dimensions
width 60 cm
height 85 cm
depth 60 cm
Capacity 12 standard place-settings
Water supply
pressure
30 Kpa Γ· 1Mpa (0.3 Γ· 10 bar)
4,3psi – 145 psi
Power supply
voltage See appliance data plate
Total absorbed
power See appliance data plate
Fuse See appliance data plate
This dishwasher conforms to
the following European
Community Directives:
-73/23/EEC dated 19/02/73
(Low Voltage) and subsequent
modifications
-89/336/EEC dated 03/05/89
(Electromagnetic Compatibility)
and subsequent modifications
-97/17/EC (Labelling)
2002/96/EC (WEEE)
Technical data


Product specificaties

Merk: Indesit
Categorie: Vaatwassers
Model: IDL 5055 SK.2

Heb je hulp nodig?

Als je hulp nodig hebt met Indesit IDL 5055 SK.2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Vaatwassers Indesit

Handleiding Vaatwassers

Nieuwste handleidingen voor Vaatwassers