Illustra IFS16-M10-BT03 Handleiding

Illustra Bewakingscamera IFS16-M10-BT03

Lees hieronder de 📖 handleiding in het Nederlandse voor Illustra IFS16-M10-BT03 (3 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 41 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

Camera Installation

First, attach a mounting plate or mounting arm to the surface that you

want to attach the camera. See applicable mounts in the table below:

Mount Product Code

Description on label

IBPN-M-IS12-0

Flex Multi-sensor Ceiling bracket

IBWS-M-ISWB-0

Flex Multi-sensor Wall bracket

IBCR-M-ISWT-0

Flex Multi-sensor In-Ceiling bracket

IBJB-M-ISWB-0

Flex Multi-sensor Junction bracket

Figure 4

Q S Guick tart uide

( - -8200 1938 01_B0)

Illustra Flex Gen 2 Multi Sensor Dome Camera

In the box

 Multi Sensor Dome 4 x camera sensor modules 1 x and

 1 x Torx wrench

 1 x Quick Start Guide

 2 x Moisture absorbers and absorber guide

 1 x Test monitor cable

 1 x Waterproof cap and Gasket

Installation tools

 Torx wrench

 Screw driver

Note: The camera should only be installed by qualied installer Na . o

user serviceable parts inside. Refer servicing to qualied personnel.

Before you start or install, refer to and read all important Safety related ‘ ’

information provided in the user’s manual at

https://illustracameras.com/cameras/

Camera Parts: Figure 1

Figure 1

Quick reference

 Default IP: 192.168.1.168 (DHCP enabled)

 Default Username / Password: admin / admin

 When you rst log into the camera you must change Note:

the password. Click the ‘Change Password’ button and enter

a new password as per the on screen password guidelines.

 Power: DC12V / PoE IEEE .3at PoE+ 802

Camera sensor modules assembly

1. Use the Torx wrench to remove the four screws on the camera

dome (Figure 1) and remove the dome from the camera base.

2. Take the four sensor modules out of their boxes and assemble

them on to the sensor module block (Figure 2).

Note: First, align the sensor module block arrow guide with the

base's arrow guide and gently press the sensor module into the

base until it is completely seated.

Figure 2

Camera buttons

Figure 3

Reset Button: Pressing and holding the ‘Reset’ button for 5 seconds

returns the camera to its factory default settings.

Test Monitor Cable Port and Video Select Switch: Connecting the

Test Monitor Cable to this port and to a video monitor lets installers

inspect and align each camera module. Use the ‘Video Select Switch’ to

select the camera.

Camera Installation (continued)

1. To install a camera mount see the mounting Quick Start Guide

at https://illustracameras.com/accessories/.

2. Hold the camera base up to the mount and place all cables

through the cable hole on the camera mount.

3. Align the two metal pins on the top of the camera base with the

two holes on the mount and rotate the camera base so that the

camera base sits into the mount.

Note: The dge on the camera base (Figure 5) aligns with the bri

‘lock’ and ‘unlock’ bridges on the mount.

Figure 5

4. To securely attach the camera base to the mount you must

insert the two mounting screws provided with the mount into the

two holes on the camera base (Figure 3) .

5. Adjust the four camera modules (Figure 6) on to the four

magnetics on the camera base to ensure the best view.

Note: Align the four camera modules as per one of the three

example shown in Figure 6.

Note: Ensure that the camera modules are level with the dome

and that the base guide is resting flat on the magnetic track.

Web GUI (continued)

Figure 10

5. Channel Select button VLC Plug-in only: Selects one of three –

camera streams for web GUI display. Each sensor supports Note:

up to three streams.

6. Camera Controls:

 PTZ Control / Preset Not supported in web GUI.–

 Speaker Control and MIC Supported.–

 Alarm Input / Relay Out - Supported.

7. Motion Detection indicator. Motion –

8. Camera Time - Displays the camera time.

Camera Installation (continued)

Figure 6

Note: Ensure that the camera module angle does not exceed 60

degrees. See Figure 7.

Figure 7

Camera Installation (continued)

6. Use the Torx wrench to securely attach the dome cover to the

camera base.

7. Remove the outer protective lm from the dome cover to

complete the installation.

Camera cable port connections

See the camera cable port connections in Figure 8.

Figure 8

Figure 8: Camera cable port descriptions

1. Connect the DC12V power cable to the power cable port Power:

on the camera.

‘ ’OR

Network: Connect the camera's network cable to an 802.3at

PoE+ switch.

2. Audio Output: Connect the audio output device cable to the

‘Audio Output’ camera cable port on the camera.

3. Audio Input: Connect the audio input device cable to the ‘Audio

Input’ camera cable port on the camera.

4. Alarm Output: Connect the alarm output device cable to the blue

and grey cables on the camera ‘Alarm/Out’ cable.

5. Alarm Input: Connect the alarm input device cable to the yellow

and white cables on the camera ‘Alarm/In’ cable.

Web GUI

Note: Use IE10 (or above) or Chrome to access the camera web GUI.

See the web GUI screen layout in Figure 9 and the descriptions below. ir

Web GUI (continued)

Figure 9

1. Live video display – This is the cameras live video stream.

2. Setup button – Provides access to the conguration GUI.

( . Video/Network/Events/Records/Security Congurations). E.g

3. Select Viewer –Select individual video streams or Quad (VLC

plug-in only).

4. Live Viewer Select one option: VLC plug-in or HTML (MJPEG). –

See Figure 10.

Warnings

 This product is intended for professional installation, please follow

local wiring regulations.

 Do not install where children are likely to have access.

 Be sure to use only the standard adapter that is specied in the

specication sheet. Using any other adapter could cause re,

electrical shock, or damage to the product.

 Incorrectly connecting the power supply or replacing battery may

cause explosion, re, electric shock, or damage to the product.

 Do not connect multiple cameras to a single adapter. Exceeding

the capacity may cause abnormal heat generation or re.

 Securely plug the power cord into the power receptacle. Insecure

connection may cause re.

 When installing the camera, fasten it securely and rmly.

 Do not place conductive objects (e.g. screw drivers, coins, metal

things, etc.) or containers lled with water on top of the camera.

Doing so may cause personal injury due to re, electric shock, or

falling objects.

 To prevent damage which may result in re or electric shock

hazard, do not expose this appliance to rain or moisture.

JOHNSON CONTROLS, TYCO and ILLUSTRA are trademarks and/or registered

trademarks. Unauthorized use is strictly prohibited.

Product specificaties

Merk:	Illustra
Categorie:	Bewakingscamera
Model:	IFS16-M10-BT03

Heb je hulp nodig?

Als je hulp nodig hebt met Illustra IFS16-M10-BT03 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Bewakingscamera Illustra

Illustra IPS02-B15-OI03 Handleiding

9 Juli 2023

Illustra IES02MFBNWIYB Handleiding

9 Juli 2023

Illustra IPS02-B12-OI03 Handleiding

9 Juli 2023

Illustra IES02B1BNWIYB Handleiding

7 Juli 2023

Illustra IFS16-M10-BT03 Handleiding

7 Juli 2023

Illustra IPS05-B16-OI03 Handleiding

7 Juli 2023

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

Axis Q1800-LE-3 Handleiding

23 December 2024

Honeywell HC35WE5R3 Handleiding

20 December 2024

Honeywell Performance H4W8PER2V Handleiding

20 December 2024

Hikvision DS-2CE12KF3T-LS Handleiding

18 December 2024

Hikvision DS-2CE78D0T-LXTS/A Handleiding

18 December 2024

TP Link VIGI C450 Handleiding

18 December 2024

Hikvision DS-2CE76U0T-LPF Handleiding

18 December 2024

Hikvision DS-2CE78U0T-LF Handleiding

18 December 2024

Hikvision DS-2CE16U0T-LPF Handleiding

18 December 2024

Hikvision DS-2CE72KF3T-LSYE Handleiding

18 December 2024